Oxygen potential measurements of Am0.5Pu0.5O2−x by EMF method

The dependence of the oxygen potentials on oxygen non-stoichiometry and temperature of Am_0.5Pu_0.5O_2−x has been obtained by the electromotive force (EMF) method with the cell: (Pt) air |Zr(Ca)O_2−x| Am_0.5Pu_0.5O_2−x (Pt). The x value of Am_0.5Pu_0.5O_2−x was changed at 1333 K over 0.02 < x ? 0.25 by the coulomb titration method. The temperature dependence of the oxygen potential was also measured over the range of 1173-1333 K. It was found that the oxygen potential decreased from −80 to −360 kJ mol⁻¹ with increasing x from 0.021 to 0.22 at 1333 K and that it remained almost constant at −360 kJmol⁻¹ around x = 0.23. It was concluded that Am_0.5Pu_0.5O_2−x should be composed of the single fluorite-type phase over 0.02 < x ? 0.22 and the mixed phases of fluorite-type and (Am, Pu)₉O₁₆ at around x = 0.23.     

Microstructural analysis of the stir zone of Al alloy produced by friction stir spot welding

The present study applied friction spot joining (FSJ), which was recently developed as a lap joining technique of Al alloys, to two sheets of Al alloy 6061, 1 mm in thickness, and then examined the microstructural feature in the weld. The weld had the nugget-shaped stir zone around the exit hole of the probe, and the stir zone exhibited the equiaxed grain structure having finer grain size than that of the base material. The crystallographic texture analysis using electron backscattered diffraction method suggested that the material movement occurred along the rotating direction of the welding tool in the wide region including the stir zone. In the periphery of the nugget-shaped stir zone, which was characterized as the region having the finer grain size than that of the stir zone interior, any inclusions and precipitates were not found in the SEM scale. The weld was softened around the weld centre. The softening could be explained by dissolution and/or growth of the strengthening precipitates due to thermal cycle of FSJ.     

Determination of sucralose in foods by HPLC using pre-column derivatization

The development of a sensitive pre-column derivatization high-performance liquid chromatography (HPLC) method for determination of sucralose is reported. Sucralose is converted into a strongly ultraviolet (UV)-absorbing derivative, possessing strong absorption at 260 nm, by treatment with p-nitrobenzoyl chloride (PNBCl). Homogenized samples were dialyzed and washed with a Bond Elut ENV cartridge, then the eluate was evaporated to dryness and the residue was derivatized. Subsequently, the sucralose derivative was purified with hexane-ethyl actate (9:1) in a silica cartridge, and then the sucralose derivative was eluted with acetone. HPLC was performed on a phenyl column, using acetonitrile-water (73:27) as a mobile phase with UV detection (260 nm). The calibration curve was linear in the range of 1 microgram/mL to 50 micrograms/mL of sucralose. The recoveries of sucralose from eight kinds of foods spiked at the levels of 0.20 and 0.05 g/kg of sucralose were more than 76.2% with SD values in the range from 0.90% to 4.31%. The quantitative limit of the developed method was 0.005 g/kg for sucralose in samples.     

Improvement in mechanical properties of dental cast Ti-6Al-7Nb by thermochemical processing

Hydrogenation and dehydrogenation, that is, thermochemical processing (THP) and its variation with a post-heat treatment (THPH), are investigated in order to improve the balance of strength, elongation, and fatigue strength of cast Ti-6Al-7Nb and Ti-6Al-4V for dental applications. Microstructures of both cast alloys change from coarse Widmanst?tten α structure to super fine α structure with an average diameter of 3 μm by conducting THP or THPH. Tensile strength and fatigue limit of cast Ti-6Al-7Nb and Ti-6Al-4V increase by around 10 and 40 pct, respectively, as compared with those of both as-cast alloys. The balance of strength and ductility of cast Ti-6Al-7Nb is improved by conducting THPH as compared with the case where THP is conducted. This improvement is due to the plastic deformability of unstable β phase because the lattice constant of β phase in each alloy conducted with THPH is much greater than that of each as-cast alloy.     

Simultaneous three-dimensional step-height measurement and high-resolution tomographic imaging with a spectral interferometric microscope

A noncontact, nonmechanical scanning, wide-field spectral interference microscope is developed for simultaneous measurement of three-dimensional step-height of discontinuous objects and tomographic imaging. A superluminescent diode (SLD) is used as a broadband light source and a liquid-crystal Fabry-Perot interferometer (LC-FPI) as a frequency-scanning device. By means of changing the injection current to the SLD, the spectral profile of the SLD is equalized, and a constant light input to the interferometer is achieved over the entire frequency-scan range. The Fourier-transform technique is used to determine both the amplitude and the phase of spectral fringe signals. Three-dimensional height distribution of a discontinuous object is obtained from the phase information, whereas optically sectioned images of the object are obtained either from the amplitude information alone or from the combination of both the amplitude and phase information. Experimental results with submicrometer resolution are presented for both step-height measurement and tomographic sectioning.     

An integrated model for the design of end-of-aisle order picking system and the determination of unit load sizes of AGVs

In this paper, we deal with an assembly line production system in which an automated guided vehicle (AGV) delivers parts to each workstation of assembly lines from a miniload automated storage/retrieval system (AS/RS). Each assembly production line is characterized by a sequence of workstations linked together for the production of a given type of product. We consider simultaneously the design problem of miniload AS/RS and the problem of determining a unit load size of the AGV. First, a non-linear mathematical model is formulated under a proposed AGV dispatching policy. And then, we determine an appropriate sequence of lines of the vehicle visits. Finally, based on the characteristics of the objective function and feasible region of the decision variables, a heuristic solution procedure is developed to find a near optimal solution. To examine the validity of the model, an example problem is solved.     

Responses of maxillary sensilla styloconica inBombyx mori to glucosides fromOsmunda japonica,a nonhost plant

We isolated glucosides from the royal fern,Osmunda japonica, which elicit a deterrent response in larvae ofBombyx mori. These compounds were absent in taro (Colocasia antiquorum) and castor-oil plant (Ricinus communis) leaves and did not evoke responses of sensory cells in the lateral and medial sensilla styloconica ofSpodoptera litura. This glucoside extract of the royal fern leaves stimulates receptors generally associated with deterrent. It is also possible that this compound may act as a behavioral deterrent, and from actual feeding tests, it is suggested that this compound may prevent feeding in some monophagous insects, such asBombyx mori. The deterrent glucoside possesses a noncyclic aglycon.