Acidogenic fermentation of blended food‐waste in combination with primary sludge for the production of volatile fatty acids

The performance of a laboratory‐scale anaerobic acidogenic fermenter fed with a mixture of blended kitchen food‐waste and primary sludge from a sewage treatment plant was investigated for the production of volatile fatty acids (VFA). The operating variables for acidogenic fermentation were kitchen food‐waste content (10 and 25 wt %), hydraulic retention time (HRT: 1, 3 and 5 days), temperature (ambient: 18 ± 2 °C, and mesophilic: 35 ± 2 °C) and pH (varied from 5.2 to 6.7). The experimental results indicated that effluent VFA concentrations and VFA production rates were higher at ambient temperature than at mesophilic conditions. The net amount of VFA with 10 wt % food‐waste increased up to 920 mg dm^?3 with an increase of HRT, but contrasting results (a decrease of 2610 mg dm^?3) were found due to the conversion of VFA into biogas in the case of 25 wt % food‐waste, which increased significantly at HRT of 3–5 days. In terms of biogas composition (CO₂ and CH₄), the organic matter was converted into CO₂ through the oxidative pathway by facultative species at low temperature while mesophilic temperature and optimum pH (6.3–7.8) played a pivotal role in increasing rate of conversion of VFA into biogas by methanogenesis. Rates of VFA production and their conversion are dependent on the food‐waste content in the mixture. Yet, the higher concentration of food‐waste (25% compared with 10%) did not produce VFA proportionally due to the increased rate of conversion of VFA into gaseous products. The maximum VFA production rate (0.318 g VFA_produced g^?1 VS_fed day^?1) was achieved in the 10 wt % food‐waste at ambient temperature and at a 5‐day HRT. Copyright © 2005 Society of Chemical Industry     

A New Image Analysis Based Method for Measuring Electrospun Nanofiber Diameter

In this paper, a new image analysis based method for electrospun nanofiber diameter measurement has been presented. The method was tested by a simulated image with known characteristics and a real web. Mean (M) and standard deviation (STD) of fiber diameter obtained using this method for the simulated image were 15.02 and 4.80 pixels respectively, compared to the true values of 15.35 and 4.47 pixels. For the real web, applying the method resulted in M and STD of 324 and 50.4 nm which are extremely close to the values of 319 and 42 nm obtained using manual method. The results show that this approach is successful in making fast, accurate automated measurements of electrospun fiber diameters.     

An analytical method for the calculation of static characteristicsof linear step motors for control rod drives in nuclear reactors

An analytical method for calculating static characteristics of linear dc step motors (LSM) is described. These multiphase passive-armature motors are now being developed for control rod drives (CRD) in large nuclear reactors. The static characteristics of such LSM is defined by the variation of electromagnetic force with armature displacement and it determines motor performance in its standing and dynamic modes of operation. The proposed analytical technique for calculating this characteristic is based on the permeance analysis method applied to phase magnetic circuits of LSM. Reluctances of various parts of phase magnetic circuit is calculated analytically by assuming probable flux paths and by taking into account complex nature of magnetic field distribution in it. For given armature positions stator and armature iron saturations are taken into account by an efficient iterative algorithm which gives fast convergence. The method is validated by comparing theoretical results with experimental ones which shows satisfactory agreement for small stator currents and weak iron saturation     

Polymorphism of bacteriophage T7

For viruses made of nucleic acid and protein, the structure of the protein outer shell has, in the past, been found to be uniquely determined by the viral genome. However, here, non-denaturing agarose gel electrophoresis of bacteriophage T7 reveals two states of the mature T7 capsid; the conditions of growth are found to alter the population by T7 of these two electrophoretically defined states. Both states have been previously observed for a genetically altered T7 and they are observed here for wild-type T7. The average electrical surface charge density of a bacteriophage particle (delta) determines its state; the delta of particles in both states is negative. For a given condition of growth, the population of these two states is influenced by the extent to which the major T7 outer shell protein, p10A, is accompanied by its minor readthrough variant, p10B. Comparison of the two electrophoretic states reveals the following. (1) No difference in radius is present in the outer shell (+/-2%). (2) As the pH of electrophoresis is either increased or decreased from neutrality, the state becomes more highly populated for which delta is greater in magnitude (state 1). By changing the pH, some T7 particles are made to change state. (3) Particles in state 1 adsorb less quickly to host cells than do the particles in the alternative state (state 2). This latter observation suggests the hypothesis that state 1 evolved to reduce the probability of re-initiating an infection when conditions are not favorable for growth. This hypothesis is supported by the observation that, as conditions of growth become apparently more unfavorable, progeny increasingly populate state 1.     

Visceral leishmaniasis: II. Histiocyte ultrastructure in bone marrow associated with low level of parasitaemia and mimicking malignant histiocytosis

The ultrastructural features of histiocytes in the bone marrow (BM) were studied in a febrile, splenomegalic and pancytopenic Sudanese patient who was diagnosed by one of us as visceral leishmaniasis (VL) associated with low level of parasitaemia and mimicking malignant histiocytosis (MH). Serial thick (STS) and ultrathin (SUT) sections showed that the BM was hypercellular and markedly infiltrated by large histiocytes with prominent phagocytosis. A thorough examination of various ST and UT section revealed only a single, typical Leishman-Donovan body. At transmission electron microscopy (TEM) level, two principal types of histiocytic cells were identified: Type I, subdivided into two subtypes, were actively phagocytic histiocytes (PH) with large digestive vacuoles and primary lysosomes; type II were nonphagocytic histiocytes (nPH) with primary lysosomes only. The rate of PH to nPH ws 7:2 in plastic STS. The interaction between the PH and ingested cells is described. Both types of cell were morphologically similar to previously described malignant histiocytic cells. However, this study showed a better characterization of PH during VL.     

Consistent labeling of tracked objects in multiple cameras with overlapping fields of view

We address the issue of tracking moving objects in an environment covered by multiple uncalibrated cameras with overlapping fields of view, typical of most surveillance setups. In such a scenario, it is essential to establish correspondence between tracks of the same object, seen in different cameras, to recover complete information about the object. We call this the problem of consistent labeling of objects when seen in multiple cameras. We employ a novel approach of finding the limits of field of view (FOV) of each camera as visible in the other cameras. We show that, if the FOV lines are known, it is possible to disambiguate between multiple possibilities for correspondence. We present a method to automatically recover these lines by observing motion in the environment, Furthermore, once these lines are initialized, the homography between the views can also be recovered. We present results on indoor and outdoor sequences containing persons and vehicles.     

An overview of FDA medical device regulation as it relates to deep brain stimulation devices.

The United States Food and Drug Administration (FDA) is charged with assuring the safety and effectiveness of a variety of medical products and the FDA's Center for Devices and Radiological Health is responsible for premarket and postmarket regulation of medical devices. In this paper, we review--from device classification and clinical studies to the final marketing application--FDA's premarket requirements and postmarket requirements as they relate to deep brain stimulation devices.     

Synthesis and activation of Pt nanoparticles with controlled size for fuel cell electrocatalysts

Well-dispersed Pt nanoparticles with controlled size and narrow size distribution were prepared by polyalcohol reduction of platinum acetylacetonate, using oleylamine as a capping agent. The particle size was varied from 3.5 nm to 11.5 nm by decreasing the amount of oleylamine added in the synthesis. Size selection of the as-prepared particles by solvent fractionation yielded nearly monodispersed Pt particles. The as-prepared particles were loaded on a carbon support by physical deposition, but showed no electrocatalytic activity due to the oleylamine bound to the particle surface. The particles were activated for electrocatalysis after heating the particles in air at 185 °C for 5 h, conditions that gave no particle-sintering and no oxidation. Cyclic voltammetry showed that the particles after the heat treatment in air were electrocatalytically active for methanol oxidation. The smaller 3.5 nm and 4.0 nm Pt particles had a higher intrinsic activity for methanol oxidation, but a lower tolerance to CO poisoning, compared with 6.0 nm, 9.5 nm and 11.5 nm particles. CO-stripping results suggest that CO is more easily oxidized on larger Pt particles.