ANT-colony based disjoint set assortment in wireless sensor networks

Wireless Networks - Wireless sensor network (WSN) consists of small sized devices containing different sensors to monitor physical, environmental and medical conditions during surveillance of...     

Role of Nd-Ni on structural,spectral and dielectric properties of strontium-barium based nano-sized X-type ferrites

The influence of neodymium and nickel substitution on structural and dielectric parameters was investigated in strontium-barium X-type hexagonal ferrites having composition SrBaCu_2?xNi_xNd_yFe_28?yO₄₆ (x = 0, 0.2, 0.4, 0.6, 0.8, 1 and y = 0, 0.02, 0.04, 0.06, 0.08, 0.1). Sol-gel method was employed for synthesizing these hexagonal ferrites. The XRD plots of all studied materials which were annealed at 1250 °C show single phase characteristics. Lattice parameter ‘c’ increased as a consequence of larger radius of rare earth ion (Nd³⁺) as compared to (Fe³⁺), while lattice parameter ‘a’ showed very small variation. The cell volume was obtained in the range 2508.32–2523.75 (ų). The inclusion of Nd-Ni also affected X-ray density, bulk density and porosity. The FTIR spectroscopy indicated the particular absorption peaks of hexagonal ferrites and it was performed in the range of 500–700 cm^?1. On account of Nd-Ni doping, the dielectric constant, dielectric loss and AC-conductivity showed decreasing trend. The occupancy of Nd³⁺ ions at octahedral site impedes the valence alternation of Fe³⁺; therefore there was decrease in dielectric permittivity. Ac conductivity has been decreased from 9.14 to 6.49 (Ω cm)^?1 at frequency of 2.7 GHz. The Cole-Cole plots of synthesized materials noticeably revealed grain boundary contribution. The appearance of single semi-circle in impedance Cole-Cole graphs confirms the exceptional role of grain boundaries in the conduction process. The considerably lower dielectric parameters of investigated nano X-type ferrites propose their feasibility for high-frequency applications (phase shifters, dielectric resonators, stealth technology etc).     

Ballistic behavior of plain and reinforced concrete slabs under high velocity impact

This work presents a numerical simulation of ballistic penetration and high velocity impact behavior of plain and reinforced concrete slabs. In this paper, we focus on the comparison of the performance of the plain and reinforced concrete slabs of unconfined compressive strength 41 MPa under ballistic impact. The concrete slab has dimensions of 675 mm × 675 mm × 200 mm, and is meshed with 8-node hexahedron solid elements in the impact and outer zones. The ogive-nosed projectile is considered as rigid element that has a mass of 0.386 kg and a length of 152 mm. The applied velocities vary between 540 and 731 m/s. 6 mm of steel reinforcement bars were used in the reinforced concrete slabs. The constitutive material modeling of the concrete and steel reinforcement bars was performed using the Johnson-Holmquist-2 damage and the Johnson-Cook plasticity material models, respectively. The analysis was conducted using the commercial finite element package Abaqus/Explicit. Damage diameters and residual velocities obtained by the numerical model were compared with the experimental results and effect of steel reinforcement and projectile diameter were studies. The validation showed good agreement between the numerical and experimental results. The added steel reinforcements to the concrete samples were found efficient in terms of ballistic resistance comparing to the plain concrete sample.     

Evaluation of microbial toxins,trace elements and sensory properties of a high-theabrownins instant Pu-erh tea produced using Aspergillus tubingensis via submerged fermentation

Theabrownins (TB) are polymeric phenolic compounds associated with the multiple bioactivities of Pu-erh tea, a post-fermented Chinese dark tea. High-TB instant Pu-erh tea was produced via a novel submerged fermentation (SF) using Aspergillus tubingensis and compared with samples produced commercially via the conventional solid-state fermentation (SSF). Viable microorganisms and microbial toxins, especially aflatoxins B₁, G₁, B₂, G₂, cyclopiazonic acid, fumonisins B₁, B₂, B₃ and ochratoxin A, were below the detection limit in all samples. Fewer microbial metabolites were found in SF instant tea compared with the SSF teas. Based on an adult consuming 1 g of instant Pu-erh tea daily, the dietary intake of investigated elements was below the safe limits recommended by various authorities. Tasters viewed the instant tea infusions as very mild, smooth, mellow and full. This suggested that submerged fermentation using A. tubingensis offers a speedy and safe alternative to commercial production of instant Pu-erh tea.     

A Distributed Routing Method for Dynamic Multicasting

Single point, sender based control does not scale well for multicast delivery. For applications, such as group video or teleconferencing a low total cost multicast tree is required. In this article we present a destination driven algorithm to minimize the total tree cost of multicast tree in a dynamic situation for the whole session duration. In this heuristic approach we considered the staying duration of participants are available at the time of joining. The performance of our algorithm is analyzed through extensive simulation and evaluated against several other existing dynamic multicast routing and also against one well known near optimum heuristic algorithm used for solving Steiner tree problem. We have further tested our algorithm using erroneous information given by the joining participants. Simulation results show that its performance does not degrade that much even when the range of error is considerably high, which proves the robustness of our algorithm.     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

DESIGN AND IMPLEMENTATION OF STATE OBSERVERS IN REACTIVE DISTILLATION

This study demonstrates that state observers can be developed and applied to infer the composition profiles of reactive distillation columns from noise-contaminated temperature measurements. The design and implementation of a Kalman filter (KF) and a Luenberger observer (LO) are carried out, and their performances are quantitatively assessed. The reliability, accuracy, and robustness of the two designs method are examined and compared quantitatively. The design and implementation of a Luenberger observer are simpler and easier to carry out than those of a Kalman filter. On the other hand, a Kalman filter is found to be more robust to a noisy measurements, erroneous initial estimates, and model uncertainties. A Luenberger observer could be used for composition estimation of reactive distillation when an ideal model of the system can reasonably approximate the real system; otherwise, a Kalman filter is recommended to be applied in more practical situations.