Resolution of a Five-Component Mixture of Quaternary Ammonium Surfactants on Silica Gel 60 <Emphasis Type="Italic">F</Emphasis><Subscript>254</Subscript> High Performance Thin Layer Chromatographic Plates

The mutual separation of a mixture of cetyltrimethyl ammonium chloride (CTAC), methyl trioctyl ammonium bromide (MTOB), dodecyltrimethyl ammonium chloride (DTAC), benzyltrimethyl ammonium chloride (BTAC) and tetrabutyl ammonium bromide (TBAB), was achieved on silica high performance thin layer chromatographic plates using dimethyl sulfoxide with aqueous sodium-l-tartrate dibasic dihydrate as the solvent system. The effect of concentration of sodium-l-tartrate dibasic dihydrate on the mobility of all the five quaternaries was examined. The limit of detection of CTAC, MTOB, DTAC, BTAC and TBAB was estimated as 0.6, 0.6, 0.3, 0.6 and 0.3 μg/zone, respectively. The method developed was utilized to identify these surfactants in different spiked water samples after their preliminary separation.     

Fully automated runtime enforcement of component-based systems with formal and sound recovery

International Journal on Software Tools for Technology Transfer - We introduce runtime enforcement of specifications on component-based systems (CBS) modeled in the behavior, interaction and...     

Mechanochemical degradation of poly(vinyl fluoride) by sodium hydroxide measured by microindentation

The degradation of the mechanical properties of deformed PVDF during its mechanochemical ageing in sodium hydroxide (soda) was followed by microindentation measurements, especially the local reduction of the elastic modulus and the hardness. This allows measurements on a local scale of the mechanical properties on the surface and in-depth as a function of the strain level and the ageing time. Microindentation tests with Berkovich indenter have been performed with a Nanoindenter XP^® (MTS). Measurements are made at penetration depth less than 2 μm for an applied load of 10 mN. During ageing in soda (Ph 14) at 90 °C up to 16 days, various deformations ε (0, 22 and 38%) are imposed on PVDF tensile specimen. For the first two imposed deformations (ε = 0 and ε = 22%), mechanical degradation is limited to some percent (less than 7%). For the greatest deformation (ε = 38%), mechanical degradation continues to decrease with ageing time (more than 21%). Microindentation tests show that a range of low deformations exists in which the mechanochemical degradation is limited and no limitation is observed for larger imposed deformation.     

A method for computation of surface roughness of digital elevation model terrains via multiscale analysis

In this paper, an algorithm to compute surface roughness of digital elevation model (DEM) terrains via multiscale analysis is proposed. The algorithm employs the lifting scheme to generate multiscale DEMs. At each scale, the areas of pixels that are modified are computed. Granulometric analysis is employed to compute the average area of curvature regions in the terrain, and the average roughness of the terrain due the distribution of curvature regions. The selected case studies of the algorithm implementation demonstrated that the proposed algorithm provides a surface roughness parameter that is realistic with respect to the amplitudes and frequencies of the terrain, invariant with respect to rotation and translation, and has intuitive meaning. The algorithm allows for a good quantification of a region’s convexity/concavity over varying scales, distinguishing between shallow and deep incisions of valleys and ridges of the terrain, and hence, provides an accurate surface roughness parameter.     

Calorimetric Assessment of Rates of Desorption

This paper concerns the further testing of a new double calorimeter. We earlier reported initial development of the calorimeter and thereafter inferred rates coefficients for adsorption of moisture under a “large pressure jump.” (The test materials were silica gel type A and water.) The paper presents a further check on the calorimeter by demonstrating that measured desorption and adsorption rates were compatible. A disappointing aspect was an unintended near step change in condenser pressure at the start of the experiment. The condenser design was deficient, and better drainage is needed in the future to maintain vapor in immediate contact with cold surfaces. Notwithstanding the lower than intended pressure driving force, the heat addition to the silica gel was measurable, following an exponential pattern against time with regression coefficient better than 99%. The rate coefficients that fitted each data set were broadly in line with coefficients reported for adsorption (within the limits of experimental error).     

A review of investigations on liquid fuel combustion in porous inert media

Utilization of a porous medium for combustion of liquid fuels is proved to be a promising approach for future applications. The porous medium burner for liquid fuels is more advantageous than the conventional open spray flame burner for several reasons; these include enhanced evaporation of droplet spray owing to regenerative combustion characteristics, low emission of pollutants, high combustion intensity with moderate turn-down ratio and compactness. This article provides a comprehensive picture of the global scenario of research and developments in combustion of liquid fuels within a porous medium that enable a researcher to determine the direction of further investigation. Accordingly, a glossary of the important terminology, the modeling approach, advances in numerical and experimental works and applications are included. The papers published in standard journals are reviewed and summarized with relevant comments and suggestions for future work.     

Compatibilization Effects of PE-g-MA on Mechanical,Thermal and Swelling Properties of High Density Polyethylene/Natural Rubber/Thermoplastic Tapioca Starch Blends

Effect of polyethylene grafted maleic anhydride (PE-g-MA) on mechanical, thermal and swelling characteristic of high density polyethylene (HDPE)/natural rubber (NR)/thermoplastic tapioca starch (TPS) blends were studied. The measurements from differential scanning calorimetric (DSC), dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA), proved the effectiveness of PE-g-MA as compatibilizer in improving the miscibility between HDPE/NR – TPS blends. A decrement in crystallinity index was found after adding PE-g-MA. It is due to restriction in mobility of the HDPE chains. In the presence of PE-g-MA, the blends have better thermal stability. On top of that, the storage modulus which is reflected to the blend stiffness also increased as indicated the improvement in HDPE/NR – TPS interaction.     

Palladium nanoparticles as reusable catalyst for the synthesis of N-aryl sulfonamides under mild reaction conditions

An efficient palladium nanoparticles-catalyzed N-arylation of sulfonamides and sulfonyl azides is described. This procedure serves as an active protocol for intermolecular C–N bond formation using Pd(OAc)₂ in PEG-400 under air. Aryl bromides and triflates react at 35°C, while aryl chlorides require heating to 50°C and give the desired products only in low yields. This reaction proceeds smoothly in acceptable yields using low catalyst loading.     

Degradation of PCBs in a marine sediment treated with ionizing and UV radiation

Radiolytic (electron beam) and photolytic (ultraviolet, UV) dechlorination of polychlorinated biphenyls (PCBs) in a marine sediment are described. Samples of a PCB-laden marine sediment, Standard Reference Material (SRM) 1944, NewYork/New Jersey Waterway Sediment, have been mixed with aqueous alcohol solutions and irradiated with an electron beam or photolyzed. Additives, such as alcohol, enhance the radiolytic yield and PCB dechlorination. In the electron beam irradiated samples, the concentrations of 29 PCB congeners decrease with irradiation dose. At the highest dose (500 kGy), the total concentration of PCBs is decreased by 83%. Photolysis leads to little dechlorination, but photolysis with added triethylamine leads to dechlorination (about 60%). It is likely that photolysis under optimal conditions (other additives, exposure time) may be as effective as electron beam radiolysis for the dechlorination of PCBs in sediment.