Numerical and experimental study on the biofiltration of toluene vapor

We have solved both steady state and transient problems on the biofiltration of toluene vapor. The effect of inlet toluene concentration and inlet gas-flow rate on the removal rate of toluene and the elimination capacity of a lab-scale biofilter has been investigated. In this study, the effectiveness factor was a function of pollutant concentration. The dynamic solutions show good agreement with experimental results. At an inlet toluene concentration of 100 ppm, the diffusion of toluene into biofilm was obviously a rate determining step. Above 200 ppm, however, biofilm already showed full activity. The steady-state simulation confirmed that the change of elimination capacity obtained by increasing only inlet toluene concentration was the same as that obtained by increasing only flow rate of contaminated air. The maximum possible performance is about 20 g/m³h with no addition of nutrients.     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.     

Preparation and characterization of polypropylene/layered silicate nanocomposites using an antioxidant

Polypropylene (PP)/layered silicate nanocomposites were prepared via simple melt mixing of three components, PP, layered silicates modified with octadecylamine (C18-MMT) and antioxidant, to investigate the role of antioxidant. TEM and X-ray scattering results confirmed the intercalated state of silicates in PP/layered silicate nanocomposites with antioxidant. In rheological and mechanical study, the nanocomposites with antioxidant showed higher properties than those of the unfilled PP. The nanocomposite with 5 wt% C18-MMT and 0.5 phr antioxidant exhibited about 1.4 times higher tensile modulus and 1.3 times higher storage modulus than the unfilled PP. However, PP/C18-MMT without antioxidant showed lower rheological values owing to the thermal decomposition of PP and the poor compatibility between PP and C18-MMT. It could be concluded that antioxidants played an important role in enhancing the compatibility between PP and C18-MMT. According to the real time X-ray diffraction, the nanocomposite showed the weak ordering of PP crystals than the unfilled PP in the load-extension plateau region of elongation.     

Effects of Acetic Acid on the Crystallization Temperature of Sol–Gel-Derived MgO Nano-Powders and Thin Films

The influences of acetic acid addition to Mg-methoxide on the stability of the precursor and the crystallization behavior of sol–gel-derived MgO nano-powders and thin films were investigated using X-ray powder diffraction, transmission electron microscopy, Fourier-transformed infrared spectroscopy, and thermogravimetry. The addition of acetic acid enhanced the stability of the alkoxide against precipitation. Moreover, during postheat treatment of the gel powders treated with acetic acid, a significantly lowered crystallization temperature (250°C) was observed as compared to the untreated counterpart (350°C). The low-temperature crystallization of MgO, induced by the modification of Mg-methoxide with acetic acid, was related to the decomposition of organics at a lower temperature. These results could be explained in terms of the decrease of the O–R bond strength depending on the increase in the alkyl group size. MgO thin films having a high degree of crystallinity were successfully obtained from the Mg-methoxide treated with acetic acid at 300°C. The low-temperature crystallization of sol–gel-derived MgO thin films showed the feasibility for their application as a protective layer in alternative current plasma display panel cells.     

Wetting properties of polystyrene ionomers treated with plasma source ion implantation

The wetting properties of polystyrene‐based ionomers treated with plasma source ion implantation (PSII) were investigated by the measurement of water contact angles. When sulfonated ionomers were aged for a few days, the hydrophobic recovery for the ionomers became much slower than that for the nonionic polymers. However, when the samples were aged over 20 days, the water contact angle of the ionomers converged with that of the nonionic polymer. Thus, it was concluded that the ionic interaction between the ionic groups and the presence of ionic groups together resulted in the slow hydrophobic recovery and that the aging effect was significant for the ionomers. For the methacrylate ionomer of low ion content, on the other hand, it was found that the PSII treatment produced only a small change in hydrophobic recovery behavior. Thus, it was suggested that the low ionic content coupled with the small size of the ionic unit might cause changes only of a very insignificant degree in hydrophobic recovery behavior. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2500–2504, 2002     

Electrical properties of (Bi3.5La0.5)Ti3O12 thin-films prepared by liquid source misted chemical deposition

The ((Bi_3.5La_0.5)Ti₃O₁₂(BLT) thin-films used in this study were fabricated on a Pt(111)/SiO₂/Si(100) substrate by a Liquid Source Misted Chemical Deposition (LSMCD) technique. X-ray diffraction patterns showed that the BLT films were crystallized and no other phases were observed when annealed above 650 ‡C. Grain size and remnant polarizations increased with increase in the annealing temperature, while leakage current densities decreased. The remnant polarizations (Pr) increased from 2.0 to 4.8 and 19.0 μC/cm2 with increase in the annealing temperature from 650 to 700 and 750 ‡C, respectively. The BLT films annealed at 700 ‡C in O₂ showed a good fatigue resistance of reduced polarization by 10% after 10⁹ switching cycles when 9 V of bipolar voltage was applied at a frequency of 40 kHz.     

An analysis of muscles from ultrasound image using morphological information of fascia and thoracic vertebra

In this paper, we propose a new fully computerized image analysis method for measuring the thickness of muscles from ultrasound image obtained by muscle endurance test using morphological information of fascia and thoracic vertebra. Firstly, we divide the image into lumbar region and thoracolumbar region by the difference of density in image for measuring the thickness of muscles. In lumbar region, we notice that the intensity of fascia is relatively higher than other parts. Thus, we measure the thickness of muscles surrounding the fascia area. In the process, we apply median filter to candidate fascia areas for extracting candidate muscle layers between fascias. Then, the thickness of muscles we measure is that of the third layer. In thoracolumbar region, we apply region expansion method for classifying the region into subcutaneous fat part and part including thoracic vertebra. Then, we apply counting method and evolutionary computation search model to find the measuring location that is in between subcutaneous fat area and thoracic vertebra. In experiment, the proposed method is effective in measuring the thickness of muscles and avoids failures of previous studies. The performance of this approach is sufficiently comparable to that of medical experts.     

Case-based context ontology construction using fuzzy set theory for personalized service in a smart home environment

To provide context-based personalized services utilizing smart appliances in a smart home environment, we propose a framework for PersonAlized Service disCovery Using FuZZY-based CBR and Context Ontology (PASCUZZY). Basically, the PASCUZZY framework is implemented on case-based context ontology. To generate and manage the case instances on the case-based context ontology, we adopt the fuzzy set theory to transpose numerical-type context data sensed from the surrounding environment. The context is transposed to linguistic-type context instances on the context ontology. In addition, to formalize and manage the context and services as multi-attributed data, the context ontology was developed reflecting the structure of cases borrowed from case-based reasoning. Furthermore, we propose adaptation methods to adjust the generic fuzzy membership functions depending on the inhabitants’ context. It is performed by modifying the values of the membership number and/or modifying the numbers of the linguistic terms that are based on the inhabitants’ context to affect the membership numbers. The adapted membership functions return the personalized degree of memberships depending on the specialized context of a specific fuzzy variable. Inevitably, the number of cases on the case-based context ontology will be increased from time to time. We apply Ward’s method not only to reduce the search effort via a hierarchical clustering on the case-based context ontology but also to find the most similar service as a solution to the new context. To verify the superiority of the PASCUZZY framework, we perform two kinds of evaluations. First, we evaluate the effectiveness of the adaptation of the fuzzy membership functions. Second, we verify the effectiveness of the application of a clustering method to the case instances of the case-based context ontology to identify the most similar service. Results of the experiment verified the effectiveness and superiority of the PASCUZZY framework.     

Changes in pore properties of phenol formaldehyde-based carbon with carbonization and oxidation conditions

Porous carbon beads were prepared by carbonizing at 700 and 1000 °C under N₂ (NN-series) or CO₂ atmospheres (CO-series) and a subsequent oxidization with boiling nitric acid solution (13%, v/v) for 3 h (ANN- and ACO-series). BET surface area of both CO- and NN-series samples tends to increase with increasing carbonization temperature, but CO-series samples show higher BET surface areas (700 °C: 610 m²/g, 1000 °C: 780 m²/g) compared with those of NN-series samples (700 °C: 380 m²/g, 1000 °C: 580 m²/g). After acid oxidation, BET surface areas of NN-series samples increased from 580 to 650 m²/g, whereas those of CO-series samples decreased from 780 to 600 m²/g. On subsequent acid oxidation, acidic surface functional groups increased in both CO- and NN-series samples, but the CO-series samples tend to have much more acidic surface functional groups. Adsorption of halogenated methanes, such as tetra-, tri- and dichloromethanes, onto the samples of CO-, NN-, ACO- and ANN-series was thought to be driven initially by the basicity, but the acidic functional groups that could attract adsorbates via dipole-dipole interaction might hinder the adsorption of subsequently incoming adsorbates.     

Adhesion property of novel polyimides with 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride

Novel polyimides were synthesized from 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride (6FPPMDA) by a conventional two‐step process: the preparation of poly(amic acid) followed by solution imidization via refluxing in p‐chlorophenol. The diamines used for polyimide synthesis included bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide, bis(3‐aminophenyl)‐4‐trifluoromethylphenyl phosphine oxide, and bis(3‐aminophenyl)phenyl phosphine oxide. The synthesized polyimides were designed to have a molecular weight of 20,000 g/mol by off‐stoichiometry and were characterized by Fourier transform infrared, NMR, differential scanning calorimetry, and thermogravimetric analysis. In addition, their intrinsic viscosity, solubility, water absorption, and coefficient of thermal expansion (CTE) were also measured. The adhesion properties of the polyimides were evaluated via a T‐peel test with bare and silane/Cr‐coated Cu foils, and the failure surfaces were investigated with scanning electron microscopy. The 6FPPMDA‐based polyimides exhibited high glass‐transition temperatures (280–299°C), good thermal stability (>530°C in air), low water absorption (1.46–2.16 wt %), and fairly low CTEs (32–40 ppm/°C), in addition to good adhesion properties (83–88 g/mm) with silane/Cr‐coated Cu foils. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1801–1809, 2005