Preparation of PbTiO3 thin films using an alkoxide-alkanolamine sol-gel system

The stable range of PbTiO₃ sol and the processing conditions of uniform thin films were investigated using a solution of titanium isopropoxide, three kinds of alkanolamines (monoethanolamine, diethanolamine, triethanolamine), lead acetate trihydrate and isopropanol. Depending on the sol state with various alkanolamine/alkoxide molar ratios, diethanolamine (DEA) was very effective in preparing uniform and dense oxide films through room-temperature reaction, owing to its superior stability during the hydrolysis and condensation reaction. Perovskite PbTiO₃ thin films were obtained on oxidized silicon wafer above 550 °C and completely pure films were obtained at 650 °C using DEA as a complexing agent. The dielectric constant and loss tangent of these thin films fired at 650 °C for 30 min were found to be 240 and 0.01 at 1 kHz, respectively.     

Significant reduction of medical costs by differentiation therapy with all-trans retinoic acid during remission induction of newly diagnosed patients with acute promyelocytic leukemia. The Japan Adult Leukemia Study Group

OBJECTIVE: For resuscitation of hemorrhagic hypovolemia, we compared the effectiveness of (1) isotonic lactated Ringer's solution (LRS), (2) 2400 mOsm of 7.5% NaCl:6% dextran 70 (HSD), and (3) 2400 mOsm of 7.9% sodium acetate:1.9% NaCl:6% dextran 70 (HAD). DESIGN: In six randomized, blinded experiments for each solution, conscious instrumented adult sheep were hemorrhaged by removing approximately 1.8 L (42 +/- 3 mL/kg) of blood, while maintaining the mean arterial pressure (MAP) at 50 mm Hg for 2 hours. METHODS: Test solutions were infused as needed to restore the cardiac index to baseline. RESULTS: Volume requirements with HAD (236 +/- 29 mL) and HSD (244 +/- 39 mL) were significantly less (p < 0.05) than LRS (3463 +/- 234 mL). Mean arterial pressure was normalized with HSD and LRS, but not with HAD, which resulted in MAPs of 20 to 25 mm Hg less than baseline resulting from a reduced peripheral resistance. Oxygen delivery, however, was significantly higher with HAD during the resuscitation period. Acid-base balance (pH) and oxygen consumption were normalized within 5 minutes of infusion only with HAD. CONCLUSIONS: Small-volume infusion with HAD resulting in "high-flow-low-pressure" resuscitation may offer unique hemodynamic and metabolic advantages for the initial treatment of hemorrhage from trauma.     

Correlated Quantum Phenomena of Spin–Orbit Coupled Perovskite Oxide Heterostructures: Cases of SrRuO3 and SrIrO3 Based Artificial Superlattices

Unexpected, yet useful functionalities emerge when two or more materials merge coherently. Artificial oxide superlattices realize atomic and crystal structures that are not available in nature, thus providing controllable correlated quantum phenomena. This review focuses on 4d and 5d perovskite oxide superlattices, in which the spin–orbit coupling plays a significant role compared with conventional 3d oxide superlattices. Modulations in crystal structures with octahedral distortion, phonon engineering, electronic structures, spin orderings, and dimensionality control are discussed for 4d oxide superlattices. Atomic and magnetic structures, J_eff = 1/2 pseudospin and charge fluctuations, and the integration of topology and correlation are discussed for 5d oxide superlattices. This review provides insights into how correlated quantum phenomena arise from the deliberate design of superlattice structures that give birth to novel functionalities.     

Implementation and characterization of flash-based hardware security primitives for cryptographic key generation

Hardware security primitives, also known as physical unclonable functions (PUFs), perform innovative roles to extract the randomness unique to specific hardware. This paper proposes a novel hardware security primitive using a commercial off-the-shelf flash memory chip that is an intrinsic part of most commercial Internet of Things (IoT) devices. First, we define a hardware security source model to describe a hardware-based fixed random bit generator for use in security applications, such as cryptographic key generation. Then, we propose a hardware security primitive with flash memory by exploiting the variability of tunneling electrons in the floating gate. In accordance with the requirements for robustness against the environment, timing variations, and random errors, we developed an adaptive extraction algorithm for the flash PUF. Experimental results show that the proposed flash PUF successfully generates a fixed random response, where the uniqueness is 49.1%, steadiness is 3.8%, uniformity is 50.2%, and min-entropy per bit is 0.87. Thus, our approach can be applied to security applications with reliability and satisfy high-entropy requirements, such as cryptographic key generation for IoT devices.     

Robust Geodesic Regression

International Journal of Computer Vision - This paper studies robust regression for data on Riemannian manifolds. Geodesic regression is the generalization of linear regression to a setting with a...     

Designing Metallic and Insulating Nanocrystal Heterostructures to Fabricate Highly Sensitive and Solution Processed Strain Gauges for Wearable Sensors

All‐solution processed, high‐performance wearable strain sensors are demonstrated using heterostructure nanocrystal (NC) solids. By incorporating insulating artificial atoms of CdSe quantum dot NCs into metallic artificial atoms of Au NC thin film matrix, metal–insulator heterostructures are designed. This hybrid structure results in a shift close to the percolation threshold, modifying the charge transport mechanism and enhancing sensitivity in accordance with the site percolation theory. The number of electrical pathways is also manipulated by creating nanocracks to further increase its sensitivity, inspired from the bond percolation theory. The combination of the two strategies achieves gauge factor up to 5045, the highest sensitivity recorded among NC‐based strain gauges. These strain sensors show high reliability, durability, frequency stability, and negligible hysteresis. The fundamental charge transport behavior of these NC solids is investigated and the combined site and bond percolation theory is developed to illuminate the origin of their enhanced sensitivity. Finally, all NC‐based and solution‐processed strain gauge sensor arrays are fabricated, which effectively measure the motion of each finger joint, the pulse of heart rate, and the movement of vocal cords of human. This work provides a pathway for designing low‐cost and high‐performance electronic skin or wearable devices.     

Effect of stents coated with a combination of sirolimus and alpha-lipoic acid in a porcine coronary restenosis model

The aim of this study was to evaluate antiproliferative sirolimus- and antioxidative alpha-lipoic acid (ALA)-eluting stents using biodegradable polymer [poly-l-lactic acid (PLA)] in a porcine coronary overstretch restenosis model. Forty coronary arteries of 20 pigs were randomized into four groups in which the coronary arteries had a bare metal stent (BMS, n = 10), ALA-eluting stent with PLA (AES, n = 10), sirolimus-eluting stent with PLA (SES, n = 10), or sirolimus- and ALA-eluting stent with PLA (SAS, n = 10). A histopathological analysis was performed 28 days after the stenting. The ALA and sirolimus released slowly over 30 days. There were no significant differences between groups in the injury or inflammation score; however, there were significant differences in the percent area of stenosis (56.2 ± 11.78 % in BMS vs. 51.5 ± 12.20 % in AES vs. 34.7 ± 7.23 % in SES vs. 28.7 ± 7.30 % in SAS, P < 0.0001) and fibrin score [1.0 (range 1.0–1.0) in BMS vs. 1.0 (range 1.0–1.0) in AES vs. 2.0 (range 2.0–2.0) in SES vs. 2.0 (range 2.0–2.0) in SAS, P < 0.0001] between the four groups. The percent area of stenosis based on micro-computed tomography corresponded with the restenosis rates based on histopathological stenosis in different proportions in the four groups (54.8 ± 7.88 % in BMS vs. 50.4 ± 14.87 % in AES vs. 34.5 ± 7.22 % in SES vs. 28.9 ± 7.22 % in SAS, P < 0.05). SAS showed a better neointimal inhibitory effect than BMS, AES, and SES at 1 month after stenting in a porcine coronary restenosis model. Therefore, SAS with PLA can be a useful drug combination for coronary stent coating to suppress neointimal hyperplasia.     

Microalgae-Based Biohybrid Microrobot for Accelerated Diabetic Wound Healing

A variety of wound healing platforms have been proposed to alleviate the hypoxic condition and/or to modulate the immune responses for the treatment of chronic wounds in diabetes. However, these platforms with the passive diffusion of therapeutic agents through the blood clot result in the relatively low delivery efficiency into the deep wound site. Here, a microalgae-based biohybrid microrobot for accelerated diabetic wound healing is developed. The biohybrid microrobot autonomously moves at velocity of 33.3 µm s⁻¹ and generates oxygen for the alleviation of hypoxic condition. In addition, the microrobot efficiently bound with inflammatory chemokines of interleukin-8 (IL-8) and monocyte chemoattractant protein-1 (MCP-1) for modulating the immune responses. The enhanced penetration of microrobot is corroborated by measuring fibrin clots in biomimetic wound using microfluidic devices and the enhanced retention of microrobot is confirmed in the real wounded mouse skin tissue. After deposition on the chronic wound in diabetic mice without wound dressing, the wounds treated with microrobots are completely healed after 9 days with the significant decrease of inflammatory cytokines below 31% of the control level and the upregulated angiogenesis above 20 times of CD31⁺ cells. These results confirm the feasibility of microrobots as a next-generation platform for diabetic wound healing.     

A Hemispherical Image Sensor Array Fabricated with Organic Photomemory Transistors

Hemispherical image sensors simplify lens designs, reduce optical aberrations, and improve image resolution for compact wide-field-of-view cameras. To achieve hemispherical image sensors, organic materials are promising candidates due to the following advantages: tunability of optoelectronic/spectral response and low-temperature low-cost processes. Here, a photolithographic process is developed to prepare a hemispherical image sensor array using organic thin film photomemory transistors with a density of 308 pixels per square centimeter. This design includes only one photomemory transistor as a single active pixel, in contrast to the conventional pixel architecture, consisting of select/readout/reset transistors and a photodiode. The organic photomemory transistor, comprising light-sensitive organic semiconductor and charge-trapping dielectric, is able to achieve a linear photoresponse (light intensity range, from 1 to 50 W m⁻²), along with a responsivity as high as 1.6 A W⁻¹ (wavelength = 465 nm) for a dark current of 0.24 A m⁻² (drain voltage = −1.5 V). These observed values represent the best responsivity for similar dark currents among all the reported hemispherical image sensor arrays to date. A transfer method was further developed that does not damage organic materials for hemispherical organic photomemory transistor arrays. These developed techniques are scalable and are amenable for other high-resolution 3D organic semiconductor devices.