MICROSCOPIC SPREADING CHARACTERISTICS OF NONPOLAR PERFLUOROPOLYETHER FILMS

The surface diffusion characteristics of nonpolar perfluoropolyether (PFPE) Z on carbon surfaces are investigated in two regimes, submonolayer and multilayer, for nano-thin films. For the submonolayer regime, the two-dimensional, cubic van der Waals equation of state is applied to determine the dependence of the surface diffusion coefficient on the film thickness, as experimental surface diffusion coefficients increase with increasing film thickness. For the multilayer regime, a conventional fluid mechanics analysis with position dependent viscosity and a van der Waals disjoining pressure gradient is applied to investigate the surface diffusion characteristics. The present theoretical analysis qualitatively agrees with the experimental results.     

Influence of mixing cycle on the degree of mixing of calcite‐filled polyethylene upon stretching

The mixing cycle‐dependent degree of dispersion and degree of mixing of a calcite (calcium carbonate) agglomerate in high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), and linear low‐density polyethylene (LLDPE) matrices upon stretching was investigated using three different techniques: mechanical property, morphological behavior, and image analyzer analyses. The mechanical properties analyzed in terms of the tensile strength and maximum elongation resulted in that the second mixing was the best for giving a better property for all systems except the LDPE system, which exhibited no significant difference between the second and third mixings. The morphological behavior of the three compounds were different, but no distinctive difference was observed to differentiate the degree of mixing from system to system. The number‐, weight‐, and z + 1‐average diameters of the air hole and the aspect ratio upon the stretching and mixing cycle were calculated to analyze the degree of mixing of the calcite‐filled composites. As a consequence, no difference in the average diameter of the air hole was obtained among the three systems, but the aspect ratios of the air hole varied significantly. Thus, the degree of dispersion and the degree of mixing may be influenced by the average calcite agglomerate size, the average diameter of the air hole, and the aspect ratio upon stretching and mixing cycles. Those factors would be formed by the difference in chemical characteristics upon various microstructures of polyethylene and its molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 311–321, 2003     

Measurement of minimum angle of resolution (MAR) in the stereoscopic display using the optotype of stereoscopic stimuli

In stereoscopic images, the crossing point of the viewing directions of the two eyes determines the perceived depth. Assuming that accommodation is affected by the positions of the crossing point, the effect of crossing point on minimum angle of resolution (MAR) was investigated. For 40 participants, MAR was measured by two‐alternative forced choice where Snellen optotype E of up and down directions were used as two kinds of stimuli. As the crossing point of the viewing direction of the left and right eyes moves farther from the sample display, the ability to identify the direction of letter E decreases at the optotype of the same line thickness. The change of MAR shows linear trends with respect to the optical power change that are the reciprocal of the distance from the participant to the crossing points located out of screen and on screen.     

Synthesis and physicochemical characterization of amphiphilic block copolymer self‐aggregates formed by poly(ethylene glycol)‐block‐poly(ϵ‐caprolactone)

Diblock copolymers with different poly(ε‐caprolactone) (PCL) block lengths were synthesized by ring‐opening polymerization of ε‐caprolactone in the presence of monomethoxy poly(ethylene glycol) (mPEG‐OH, MW 2000) as initiator. The self‐aggregation behaviors and microscopic characteristics of the diblock copolymer self‐aggregates, prepared by the diafiltration method, were investigated by using ¹H NMR, dynamic light scattering (DLS), and fluorescence spectroscopy. The PEG–PCL block copolymers formed the self‐aggregate in an aqueous environment by intra‐ and/or intermolecular association between hydrophobic PCL chains. The critical aggregation concentrations of the block copolymer self‐aggregate became lower with increasing hydrophobic PCL block length. On the other hand, reverse trends of mean hydrodynamic diameters were measured by DLS owing to the increasing bulkiness of the hydrophobic chains and hydrophobic interaction between the PCL microdomains. The partition equilibrium constants (K_v) of pyrene, measured by fluorescence spectroscopy, revealed that the inner core hydrophobicity of the nanoparticles increased with increasing PCL chain length. The aggregation number of PCL chain per one hydrophobic microdomain, investigated by the fluorescence quenching method using cetylpyridinium chloride as a quencher, revealed that 4–20 block copolymer chains were needed to form a hydrophobic microdomain, depending on PCL block length. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3520–3527, 2006     

Sulfonated polyimide and poly (ethylene glycol) diacrylate based semi‐interpenetrating polymer network membranes for fuel cells

Semi‐interpenetrating polymer network (semi‐IPN) membranes based on novel sulfonated polyimide (SPI) and poly (ethylene glycol) diacrylate (PEGDA) have been prepared for the fuel cell applications. SPI was synthesized from 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, and 2‐bis [4‐(4‐aminophenoxy) phenyl] hexafluoropropane. PEGDA was polymerized in the presence of SPI to synthesize semi‐IPN membranes of different ionic contents. These membranes were characterized by determining, ion exchange capacity, water uptake, water stability, proton conductivity, and thermal stability. The proton conductivity of the membranes increased with increasing PEGDA content in the order of 10^?1 S cm^?1 at 90°C. These interpenetrating network membranes showed higher water stability than the pure acid polyimide membrane. This study shows that semi‐IPN SPI membranes based on PEGDA which gives hydrophilic group and structural stability can be available candidates comparable to Nafion® 117 over 70°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and swelling behavior of biodegradable hydrogels based on α,β‐poly(N‐2‐hydroxyethyl‐DL‐aspartamide)

Biodegradable polymers and the hydrogels have been increasingly applied in a variety of biomedical fields and pharmaceutics. α,β‐Poly(N‐2‐hydroxyethyl‐DL ‐aspartamide), PHEA, one of poly(amino acid)s with hydroxyethyl pendants, are known to be biodegradable and biocompatible, and has been studied as an useful biomaterial, especially for drug delivery, via appropriate structural modification. In this work, hydrogels based on PHEA were prepared by two‐step reaction, that is, the crosslinking of polysuccinimide, the precursor polymer, with oligomeric PEG or PEI‐diamines and the following nucleophilic ring‐opening reaction by ethanolamine. Soft hydrogels possessing varying degrees of gel strength could be prepared easily, depending on the amount of different crosslinking reagents. The swelling degrees, which were in the range of 10–40 g–water/dry gel, increased somewhat at higher temperature, and also at alkaline pH of aqueous solution. A typical hydrogel remained almost unchanged for 1 week, at 37°C in phosphate buffer of pH 7.4, and then seemed to degrade slowly as time. A porous scaffold could be fabricated by the freeze drying of water‐swollen gel. The PHEA‐based hydrogels have potential for useful biomaterial applications including current drug delivery system. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3741–3746, 2003     

Preparation and characterization of maleic anhydride‐g‐polypropylene/diamine‐modified clay nanocomposites

Polypropylene (PP)/montmorillonite (MMT) nanocomposites were prepared by compounding maleic anhydride‐g‐polypropylene (MAPP) with MMT modified with α,ω‐diaminododecane. Structural characterization confirmed the formation of characteristic amide linkages and the intercalation of MAPP between the silicate layers. In particular, X‐ray diffraction patterns of the modified clay and MAPP/MMT composites showed 001 basal spacing enlargement as much as 1.49 nm. Thermogravimetric analysis revealed that the thermal decomposition of the composite took place at a slightly higher temperature than that of MAPP. The heat of fusion of the MAPP phase decreased, indicating that the crystallization of MAPP was suppressed by the clay layers. PP/MAPP/MMT composites showed a 20–35% higher tensile modulus and tensile strength compared to those corresponding to PP/MAPP. However, the elongation at break decreased drastically, even when the content of MMT was as low as 1.25–5 wt %. The relatively short chain length and loop structure of MAPP bound to the clay layers made the penetration of MAPP molecules into the PP homopolymer phase implausible and is thought to be responsible for the decreased elongation at break. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 307–311, 2005     

Durable antimicrobial treatment of cotton fabrics using N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride and polycarboxylic acids

N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride (HTCC), a water‐soluble chitosan quaternary ammonium derivative, was used as an antimicrobial agent for cotton fabrics. HTCC has a lower minimum inhibition concentration (MIC) against Staphylococcus aureus, Klebsiella pneumoniae, and Escherichia coli compared to that of chitosan; however, the imparted antimicrobial activity is lost on laundering. Thus crosslinking agents were utilized to obtain a durable antimicrobial treatment by immobilizing HTCC. Several crosslinkers such as dimethyloldihydroxyethylene urea (DMDHEU), butanetetracarboxylic acid (BTCA), and citric acid (CA) were used with HTCC to improve the laundering durability of HTCC treatment by covalent bond formation between the crosslinker, HTCC and cellulose. The polycarboxylic acid treatment was superior to the DMDHEU treatment in terms of prolonged antimicrobial activity of the treated cotton after successive laundering. Also, the cotton treated with HTCC and BTCA showed improved durable press properties without excessive deterioration in mechanical strength or whiteness when compared to the citric acid treatment. With the addition of only 0.1% HTCC to BTCA solutions, the treated fabrics showed durable antimicrobial activity up to 20 laundering cycles. The wrinkle recovery angle and strength retention of the treated fabrics were not adversely affected with the addition of HTCC. Therefore, BTCA can be used with HTCC in one bath to impart durability of antimicrobial activity along with durable press properties to cotton fabric. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1567–1572, 2003     

Physical and electroresponsive characteristics of the intercalated styrene‐acrylonitrile copolymer/clay nanocomposite under applied electric fields

Styrene‐acrylonitrile copolymer (SAN)/clay nanocomposites were synthesized through an emulsion copolymerization of styrene and acrylonitrile in the presence of sodium montmorillonite, and their physical properties and electroresponsiveness under an applied electric field were characterized. Thermogravimetric analysis (TGA) showed that the thermal stability of the synthesized polymer was sustained. X‐ray diffraction (XRD) analysis confirmed the insertion of SAN into the interlayers of clay, whose separation consequently increased, as compared to those of the pristine clay. Transmission electron microscopy (TEM) was used to observe the suspended state of clay. Dry‐base electrorheological (ER) fluids were prepared by mixing intercalated SAN nanocomposite particles into silicone oil. Typical ER behavior, i.e., enhancement of shear and yield stresses in the presence of an applied electric field, was observed using a rotational rheometer equipped with a high‐voltage generator. A universal yield stress scaling equation was also found to fit our experimental data well. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 821–827, 2003     

Robust person re-identification via graph convolution networks

Person re-identification (re-id) aims to identity the same person over multiple cameras; it has been successfully applied to various computer vision applications as a fundamental method. Owing to the development of deep learning, person re-id methods, which typically use triplet networks based on triplet loss, have demonstrated great success. However, the appearances of people are similar and hence difficult to distinguish in many cases. Therefore, we present a novel graph convolution network and enhances traditional triplet loss functions. Our method defines reference, positive, and negative features for triplet loss as three vertices of a graph, respectively, and adjusts their mutual distance through learning. The method adopts graph convolutions efficiently, thereby affording low computational costs. Experimental results demonstrate that our method is superior to the baseline on the Market-1501 dataset. The proposed GCN-based triplet loss considerably contributes to improve re-identification methods quantitatively and qualitatively.