Nitrogen transformations and fate of other parameters in columnar denitrification

Soil columns were used as denitrifying reactors in the laboratory where the feed solutions were composed of nitrified solution and kitchen waste. Five different carbon (expressed as methanol) to nitrogen ratios ranging from 2:1 to 6:1 were applied to twenty soil columns. Transformation of nitrogen compounds and fate of associated parameters during denitrification were investigated. A high degree of denitrification was obtained for C:N ratios of 4:1 or higher. Rate of application was not a significant factor in this study. Most of the TKN present in the feed solutions escaped the denitrification reactors. Production of total alkalinity during denitrification was found to be somewhat lower than the values reported in the literature. In some cases the column effluents contained higher solids concentrations than in the influent.     

Stability of imperfect conical shells with helical reinforcement

The article explains a method of numerical calculation of the stability of imperfect conical shells with helical reinforcement under uniform external pressure. It also investigates the effect of the amplitude of local initial imperfections on the critical loads.Translated from Problemy Prochnosti, No. 12, pp. 67–69, December, 1991.     

Towards new indicators for the prediction of solid waste anaerobic digestion properties.

The biochemical composition can be seen as a good indicator of both the biodegradability and the methane potential of a given waste. The work presented here is an attempt to elaborate a typology of wastes and to compare it to the anaerobic degradation characteristics. The first data indicate that there is a link between the ligno-cellulosic content of the waste and the biodegradability. When dealing with application to anaerobic digestion processes, having a tool to predict the ability of the waste to be degraded could be of the greatest interest for preventing failures, estimating biogas production, methane content, or for the management of co-digestion processes.     

Vibratory drier for the chemical industry

Modern designs are examined, and technical data presented for vibratory electric and convection driers, driers with infra-red sources, and steam driers.     

Autocorrelation model-based identification method for ARMA systems in noise

A novel method for parameter estimation of minimum-phase autoregressive moving average (ARMA) systems in noise is presented. The ARMA parameters are estimated using a damped sinusoidal model representation of the autocorrelation function of the noise-free ARMA signal. The AR parameters are obtained directly from the estimates of the damped sinusoidal model parameters with guaranteed stability. The MA parameters are estimated using a correlation matching technique. Simulation results show that the proposed method can estimate the ARMA parameters with better accuracy as compared to other reported methods, in particular for low SNRs.     

Model-driven systems development and integration environment

Telecommunications operators are undergoing massive transformations in order to metamorphose themselves into the ICT world and compete with agile, lean IT organisations. The main challenges facing telecommunications operators, such as BT, are to reduce costs and increase agility in deploying software systems for provisioning ICT services. Despite using reusable capabilities and COTS packages, the major source of increased cost lies in the heavy integration tax we incur for integrating diverse systems implemented on diverse platforms and middleware, with heterogeneous data and process models. This paper looks at cost implications of lengthy and often manual migration to-and-from systems and platforms, and shows the clear business benefits of model-driven development (MDD) as defined by the Object Management Group (OMG). It is clearly demonstrated that model-driven development has matured into a practical, industrialised, scalable and evolvable technology, culminating from decades of R&D on specification and design languages, executable formalisms and domainspecific languages and language transformations.     

Nanoscale structural characteristics and electron field emission properties of transition metal–fullerene compound TiC60 films

Transition-metal compound TiC₆₀ thin films were grown by co-deposition from two separated sources of fullerene C₆₀ powder and titanium. Study of structural properties of the films, by Raman spectroscopy, atomic force microscopy, and scanning tunneling spectroscopy reveals that the films have a deformed C₆₀ structure with certain amount of sp³ bonds and a rough surface with a large number of nanoclusters. z–V tunnelling spectroscopic measurements suggest that several charge transport mechanisms are involved in as the tip penetrates into the thin film. Conventional field electron emission (FEE) measurements show a high emission current density of 10 mA/cm² and a low turn-on field less than 8 V/μm, with the field enhancement factors being 659 and 1947 for low-field region and high-field region, respectively. By exploiting STM tunneling spectroscopy, local FEE on nanometer scale has also been characterized in comparison with the conventional FEE. The respective field enhancement factors are estimated to be 99–355 for a gap varying from 36 to 6 nm. The enhanced FEE of TiC₆₀ thin films can be ascribed to structural variation of C₆₀ in the films and the electrical conducting paths formed by titanium nanocrystallites embedded in C₆₀ matrix.     

Remotely powered addressable UHF RFID integrated system

This paper presents a fully integrated remotely powered and addressable radio frequency identification (RFID) transponder working at 2.45 GHz. The achieved operating range at 4 W effective isotropically radiated power (EIRP) base-station transmit power is 12 m. The integrated circuit (IC) is implemented in a 0.5 /spl mu/m silicon-on-sapphire technology. A state-of-the-art rectifier design achieving 37% of global efficiency is embedded to supply energy to the transponder. The necessary input power to operate the transponder is about 2.7 /spl mu/W. Reader to transponder communication is obtained using on-off keying (OOK) modulation while transponder to reader communication is ensured using the amplitude shift keying (ASK) backscattering modulation technique. Inductive matching between the antenna and the transponder IC is used to further optimize the operating range.     

Polyimide foams from powder: Experimental analysis of competitive diffusion phenomena

In the present study, various diffusive processes have been investigated during foaming of powdered precursors of polyimide. A detailed analysis of the powdered precursor's characteristics allows for an enhanced morphological understanding of the resulting microstructures and foam unit cell. Parameters that are central to the foaming process such as particle morphology, volatile concentration and sorption-desorption processes are evaluated. Isothermal and non-isothermal desorption experiments have been carried out by thermogravimetric analysis (TGA), and specific diffusive processes have been correlated to thermodynamic and kinetic transitions by means of modulated differential scanning calorimetry (MDSC) of the corresponding materials. It was found that two primary fluxes of volatiles, one out of the external surface of the particles (responsible for volatile desorption) and the other into the growing bubble (responsible for vapor supersaturation inside the bubble) compete against each other creating a competitive scenario that becomes the controlling factor for potential inflation within the precursor particles.     

Bi12TiO20 synthesized directly from bismuth (III) nitrate pentahydrate and titanium glycolate and its activity

Pure phase of sillenite structure, Bi₁₂TiO₂₀, was directly synthesized using stoichiometric bismuth (III) nitrate pentahydrate and titanium glycolate by co-precipitation. The influence of pH on the structure of Bi₁₂TiO₂₀ was studied in the pH range of 3–10. The sillenite structure was characterized using XRD and FTIR. The photo-degradation reaction of 4-nitrophenol (4-NP) was used to study photocatalytic activity of Bi₁₂TiO₂₀ as a function of the preparation pH. The rate of decomposition was followed by UV-vis and TOC. The beginning concentration of 4-NP, 44 ppm, decreased to less than 1 ppm within 30 min for all prepared catalysts. It was found that the decomposition rate constant of Bi₁₂TiO₂₀ is six times higher than those of either TiO₂ or Bi₂O₃ under the same conditions.