Transfer of Heat and Moisture in Freezing of Grounds

Approximate (consistent with experiments) methods of solution of problems of freezing of moist grounds of semiinfinite and finite length with different boundary conditions have been proposed. Methods of obtaining the parameters of transfer of heat and moisture from experiments have been given. The analytical and experimental results obtained have been discussed.     

Tunneling recombination in spatially inhomogeneous structures

Methods for finding the parameters (energies and capture coefficients for electrons and holes) of the levels involved in the formation of the recombination flux are suggested. The temperature variation of these parameters for AlGaN/InGaN/GaN and InGaN/SiC structures is discussed. The parameters of the levels responsible for tunneling recombination are determined.     

Magnetic Fluids and Their Use in Transducers

Magnetic fluids are now widely used to implement transducer architectures. These fluids have valuable properties compared to traditional materials. In this column, a brief overview of magnetic fluids and their traditional uses in the field of transducers are given and some applications developed at the DIEES laboratory at the University of Catania, Italy are presented     

Exciton-polariton transition induced by elastic exciton-exciton collisions in ultrahigh quality AIGaAs alloys

The stationary and time-resolved polariton radiation in ultrahigh quality AIGaAs layers have been studied. It has been found that elastic exciton-exciton collisions lead to the appearance of a low-energy line of polariton radiation. We show that the rate of exciton-to-polariton transitions caused by elastic exciton-exciton collisions is determined not only by the density of the excitonic gas, but also by its temperature; this is in accordance with existing theoretical predictions. The text was submitted by the authors in English.     

Microstructural development and mechanical properties of interrupted aged Al-Mg-Si-Cu alloy

The effects of a recently developed interrupted aging procedure on the microstructural development and mechanical properties of the commercial Al-Mg-Si-Cu alloy 6061 have been studied using transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and mechanical testing. This so-called T6I6 temper involves partially aging the alloy at a typical T6 temperature (the underaging stage), quenching, then holding at a reduced temperature (in this case 65 °C) to facilitate further hardening (the secondary aging stage), prior to final aging to peak properties at, or close to, the initial aging (T6) temperature (the reaging stage). The T6I6 aging treatment produces simultaneous increases in tensile properties, hardness, and toughness, as compared with conventional T6. The overall improvement in the mechanical properties of 6061 T6I6 is associated with the formation of a greater number of finer, and more densely dispersed, β″ precipitates in the final microstructure. Secondary precipitation took place during the interrupted aging stage of the T6I6 temper, resulting in the formation of a large number of Guinier-Preston (GP) zones that served as precursors to the needlelike β″ precipitates when elevated temperature aging was resumed.     

Photoreactivation of Escherichia coli following medium-pressure ultraviolet disinfection and its control using chloramination.

Ultraviolet (UV) disinfection is becoming increasingly popular as an alternative disinfection technology to chlorination in recent years. In this study, we investigated the photoreactivation of Escherichia coli following medium-pressure (MP) UV disinfection of synthetic water by a bench-scale collimated beam apparatus. The UV doses ranged from 1.6 -19.7 mWs/cm2 and photoreactivation was investigated for 6 hours under fluorescent light. In addition, chloramination was applied after UV disinfection to investigate its ability to control photoreactivation. It was found that photoreactivation occurred for all UV doses tested and the increase in bacteria numbers ranged from 0.04 to 1.35 log10. However, the degree of photoreactivation decreased with increased UV doses. Chloramination experiments revealed that the addition of 0.5 mg/l of monochloramine resulted in suppression of photoreactivation for 1 hour only. An increased monochloramine dose of 1 mg/l was found to prevent photoreactivation for the entire duration of the experiment. The results of this study have shown that photoreactivation occurs even after MP UV disinfection, although it is of a lesser extent at higher UV doses. This study has also established that secondary chloramination can effectively suppress and eliminate photoreactivation with a chloramine dose of 1 mg/l.     

Mathematical modeling of high-frequency electromagnetic heating of the bottom-hole area of horizontal oil wells

The results of theoretical investigations of the possibility of using intense high-frequency electromagnetic radiation in fields of high-viscosity oils with the aim of intensifying their production have been given. Expressions of the distribution of the electromagnetic field strength and the field of heat sources occurring in an oil bed under the action of high-frequency electromagnetic radiation transferred to the bed through a horizontal well have been obtained. A two-dimensional mathematical model of the process of production of oil through horizontal wells with simultaneous high-frequency electromagnetic action has been developed. The efficiency and profitableness of the method from the viewpoint of the energy balance have been evaluated.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 77, No. 6, pp. 105–111, November–December, 2004.     

Stress State of Bent Buried Pipelines

The authors consider edge effects in buried pipelines that occur in the region of joining of a straight buried pipe and a bent insert (factory bend, elbow, or an elastically bent segment). The action of those effects results in the appearance of additional bending moments, which are proportional to the difference between the axial force in an infinite straight pipeline and that in a closed-end pipe, and depend on the geometrical parameters of the pipeline and physical-mechanical characteristics of the soil. Specific examples of analysis of elastic interaction of a pipeline with the soil for pipe bends with various radii of the bend arc are offered. It is shown that additional bending stresses may exceed appreciably the stresses from the axial force, and therefore, they should be taken into account when designing and building pipelines. The solution for an elastically bent segment has been obtained and analyzed.     

Pin&Play: the surface as network medium

Integrating appliances in the home through a wired network often proves to be impractical: routing cables is usually difficult, changing the network structure afterward even more so, and portable devices can only be connected at fixed connection points. Wireless networks are not the answer either: batteries have to be regularly replaced or changed, and what they add to the device's size and weight might be disproportionate for smaller appliances. In Pin&Play, we explore a design space in between typical wired and wireless networks, investigating the use of surfaces to network objects that are attached to it. This article gives an overview of the network model, and describes functioning prototypes that were built as a proof of concept.     

Reliability of structures in high dimensions, part I: algorithms and applications

The present paper is concerned with the estimation of structural reliability when a large number of random variables is present. A sampling technique which uses lines in order to probe the failure domain, is presented. The latter is employed in conjunction with a stepwise procedure which makes use of Markov Chains. The resulting algorithm exhibits accelerated convergence.