Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

Development of a thermal hydraulic analysis code for gas-cooled reactors with annular fuels

Gas-cooled reactors have been highlighted as a promising option for next generation reactor technology. A thermal hydraulic analysis code for gas-cooled reactors has been developed with a heat transfer model of a block element, which is solved implicitly with the helium energy equation. Validation was carried out through comparison with both experimental and analytical results. A computation module for annular fuel rods has been coupled to the code for comparative analyses of an annular fuel-based block element. At normal operation, the annular fuel shows 80 °C lower peak temperature than the solid fuel for the same power in Japan's high temperature engineering test reactor (HTTR), even though the pressure drop is higher in the annular fuel.     

CVD金刚石工具膜生长特征SEM观察

本文用不热形变栅状直丝化学气相沉积（ＣＶＤ）法生长金刚石膜，在Ｓｉ及ＷＣ－Ｃｏ硬质合金衬底上金刚石膜晶面显露规律随衬底温度和甲烷浓度而异，经适当表面处理及选择合适的工艺条件，当生长初期衬底上就呈现出良好晶形的沉积膜，衬底与膜之间的粘结力能得到提高。Ｒａｍａｎ谱分析表明此膜仅具有特征金刚石１３３２ｃｍ￣（－１）峰，通过ＳＥＭ观察揭示出盒刚石膜可在表面、侧面及棱上生长，并与衬底有良好的联结。     

Physical model of drain conductance, gd, degradation ofNMOSFET's due to interface state generation by hot carrierinjection

Degradation of analog device parameters such as drain conductance, g_d, due to hot carrier injection has been modeled for NMOSFET's. In this modeling, mobility reduction caused by interface state generation by hot carrier injection and the gradual channel approximation were employed. It has been found that g_d degradation can be calculated from linear region transconductance, g_m, degradation which is usually monitored for hot carrier degradation of MOSFET's. The values of g_d degradation calculated from g_m degradation fit well to the measured values of g_d degradation The dependence of the g_d degradation lifetime on L_eff has been also studied, this model also provides an explanation of the dependence on L_eff. The model is then useful for lifetime predictions of analog circuits in which g_d degradation is usually more important than g_m degradation     

Spectrally stable Er-fiber laser for application in phase-sensitive optical time-domain reflectometry

A high degree of frequency stability in an Er-fiber laser with the Fabry-Perot configuration was achieved using a long (25-km) optical-feedback loop. The frequency-drift rate was determined to be <1 MHz/min by observing temporal fringes in an unbalanced Mach-Zehnder interferometer. Instantaneous linewidth measured with a delayed self-heterodyne interferometer was less than the 3-kHz resolution limit. The laser was utilized in an optical time-domain reflectometry experiment to detect and locate a time-varying phase perturbation applied to an optical fiber.     

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO2 for no reduction by NH3

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO₂ for NO reduction by NH₃ was examined in a fixed-bed flow reactor. The deactivation of the catalyst was strongly dependent on reaction temperature. At high reaction temperatures over 300°C, the catalyst did not lose its initial activity up to 50 h of operation, regardless of SO₂ feed concentration from 500 to 20,000 ppm. However, at low reaction temperatures near 250°C, apparent deactivation did occur. Changes in the physicochemical properties such as surface area and sulfur content of deactivated catalyst well correlated with catalyst activity, depending upon reaction temperatures. The deactivation was due to pore blocking and/or filling by deactivating agents, which plugged and/or filled the pores of catalyst. The deactivating agents deposited on the catalyst surface were presumed to be (NH₄)₂SO₄ and/or (NH₄)HSO₄ from the results of TGA and ion-chromatography measurement.     

A novel high-efficiency linear transmitter using injection-locked pulsed oscillator

This letter presents a novel high-efficiency linear transmitter using pulse-width modulation (PWM). An envelope of radio frequency (RF) input signal is modulated by the PWM. The modulated signal is applied to the gate bias of a class F injection-locked power oscillator and switches it on and off. By filtering the pulsed oscillating output signal of the injection-locked oscillator using high-Q bandpass filter, the input signal is restored. This technique enables the transmitter to have high efficiency with good linearity. Also, there is little distortion near saturation point of an active device. The measured results show efficiency of 54.6% and very good linearity in PCS band at 26.4-dBm output power.     

Double melting behavior of cyclic tris(ethylene terephthalate)

Summary Cyclic tris(ethylene terephthalate) (CTET) was separated from oligomeric extract of poly(ethylene terephthalate) by the conventional solvent separation method. The structure of CTET was characterized by differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy. It is shown that the double melting behavior of meltcrystallized CTET is attributed to the morphological change created by heat-treatment. The effect of the morphological change on the crystal structure of CTET was also examined.     

Surface characteristics of fluorine-modified PAN-based carbon fibers

Different fluorination methods were applied to modify the surface properties of carbon fibers. The relationship between the degree of fluorination and the physicochemical properties of carbon fibers was studied using a combination of mechanical tests, elemental analysis (EA), X-ray photoelectron spectrometry (XPS), and X-ray diffraction (XRD). EA and XPS analyses of fluorinated carbon fibers showed that treatment with mixtures of F₂/O₂ introduced a much higher fluorine concentration than that with F₂ only. However, XRD analysis showed that there was no increase in the interlayer distance, due to the mild fluorination condition applied. Consequently, the oxyfluorination was one of the more effective methods to increase surface polarity of carbon fibers, which probably played an important role in improving the tensile properties of the fibers in the epoxy resin system.