Development of silicon wafer packaging technology for deep UV LED

This paper reports a deep‐ultraviolet LED (deep‐UV‐LED) package based on silicon MEMS process technology (Si‐PKG). The package consists of a cavity formed by silicon crystalline anisotropic etching, through‐silicon vias (TSVs) filled with electroplated Cu, bonding metals made of electroplated Ni/AuSn and a quartz lid for hermetic sealing. A deep‐UV LED die is directly mounted in the Si‐PKG by AuSn eutectic bonding without a submount. It has advantages in terms of size, heat dissipation, light utilization efficiency, productivity and cost over conventional AlN ceramic packages. We confirmed a light output of 30 mW and effective reflection on Si (111) cavity slopes in the Si‐PKG. Based on simulation, further improvement of the optical output is expected by optimizing DUV‐LED die mount condition.     

Ultrafine,fine, and black carbon particle concentrations in California child‐care facilities

Although many U.S. children spend time in child care, little information exists on exposures to airborne particulate matter (PM) in this environment, even though PM may be associated with asthma and other respiratory illness, which is a key concern for young children. To address this data gap, we measured ultrafine particles (UFP), PM_2.5, PM₁₀, and black carbon in 40 California child‐care facilities and examined associations with potential determinants. We also tested a low‐cost optical particle measuring device (Dylos monitor). Median (interquartile range) concentrations for indoor UFP, gravimetric PM_2.5, real‐time PM_2.5, gravimetric PM₁₀, and black carbon over the course of a child‐care day were 14 000 (11 000‐29 000) particles/cm³, 15 (9.6‐21) μg/m³, 15 (11‐23) μg/m³, 48 (33‐73) μg/m³, and 0.43 (0.25‐0.65) ng/m³, respectively. Indoor black carbon concentrations were inversely associated with air exchange rate (Spearman's rho = ?.36) and positively associated with the sum of all Gaussian‐adjusted traffic volume within a one‐kilometer radius (Spearman's rho = .45) (P‐values <.05). Finally, the Dylos may be a valid low‐cost alternative to monitor PM levels indoors in future studies. Overall, results indicate the need for additional studies examining particle levels, potential health risks, and mitigation strategies in child‐care facilities.     

Next‐generation DNA sequencing reveals that low fungal diversity in house dust is associated with childhood asthma development

Dampness and visible mold in homes are associated with asthma development, but causal mechanisms remain unclear. The goal of this research was to explore associations among measured dampness, fungal exposure, and childhood asthma development without the bias of culture‐based microbial analysis. In the low‐income, Latino CHAMACOS birth cohort, house dust was collected at age 12 months, and asthma status was determined at age 7 years. The current analysis included 13 asthma cases and 28 controls. Next‐generation DNA sequencing methods quantified fungal taxa and diversity. Lower fungal diversity (number of fungal operational taxonomic units) was significantly associated with increased risk of asthma development: unadjusted odds ratio (OR) 4.80 (95% confidence interval (CI) 1.04–22.1). Control for potential confounders strengthened this relationship. Decreased diversity within the genus Cryptococcus was significantly associated with increased asthma risk (OR 21.0, 95% CI 2.16–204). No fungal taxon (species, genus, class) was significantly positively associated with asthma development, and one was significantly negatively associated. Elevated moisture was associated with increased fungal diversity, and moisture/mold indicators were associated with four fungal taxa. Next‐generation DNA sequencing provided comprehensive estimates of fungal identity and diversity, demonstrating significant associations between low fungal diversity and childhood asthma development in this community.     

Tracking and erosion of HTV silicone rubbers of different thickness

Tracking and erosion behaviors of high temperature vulcanized (HTV)-silicone rubber (SIR) of 0.5 to 6.0 mm thicknesses were investigated in order to obtain the optimum thickness for enhancing tracking and erosion resistance under various leakage current levels. Under low leakage current, thinner samples showed a higher tracking and erosion resistance, while under medium and high leakage current, thicker samples showed better resistance to these behaviors. The optimum thickness to prolong the time to tracking and erosion failure appeared in the range of 1.0 to 3.0 mm thickness. The content of an initial low molecular weight (LMW) silicone fluid was shown to be closely related to the development of leakage current and high temperature thermal spots. The results indicate that the sample thickness is crucial to the ability of HTV-SIR to withstand a large number of high temperature thermal spots under condition of high level leakage current     

Pyrolysis of sugarcane bagasse pretreated with sulfuric acid

Pyrolysis is a promising technique for the recovery of useful gas, tar, and solid products from biomass waste. However, the low tar yields obtained from lignocellulosic biomass are a significant drawback. To enhance tar yields, sugarcane bagasse, which is the most abundant agricultural waste in Fiji, was pretreated at ambient temperature and atmospheric pressure using various sulfuric acid (H₂SO₄) concentrations. Here, the ether bonds of cellulose, hemicellulose, and lignin were partially hydrolyzed. The pretreated samples were then pyrolyzed at 500 °C, and it was confirmed that H₂SO₄-pretreatment disrupted the bagasse cell structure, with the thermogravimetry and differential thermogravimetry results confirming that decomposition occurred at lower temperatures after pretreatment. In addition, tar yields were significantly enhanced from 5.6 wt% to 13.4 wt% for the untreated and 3 M H₂SO₄-pretreated samples respectively. The main components detected in this tar product were levoglucosan, andcellulose-and hemicellulose-derived products, whose proportions were increased following pretreatment. Thus, our work demonstrates that dilute acid pretreatment enhances tar production from sugarcane bagasse due to the production of shorter chain components via the partial hydrolysis of ether bonds.     

Investigation of hydrogen storage capacity of various carbon materials

Hydrogen storage capacity of various carbon materials, including activated carbon (AC), single-walled carbon nanohorn, single-walled carbon nanotubes, and graphitic carbon nanofibers, was investigated at 303 and 77 K, respectively. The results showed that hydrogen storage capacity of carbon materials was less than 1 wt% at 303 K, and a super activated carbon, Maxsorb, had the highest capacity (0.67 wt%). By lowering adsorption temperature to 77 K, hydrogen storage capacity of carbon materials increased significantly and Maxsorb could store a large amount of hydrogen (5.7 wt%) at a relatively low pressure of 3 MPa. Hydrogen storage capacity of carbon materials was proportional to their specific surface area and the volume of micropores, and the narrow micropores was preferred to adsorption of hydrogen, indicating that all carbon materials adsorbed hydrogen gas through physical adsorption on the surface.     

Combination of cytomegalovirus enhancer with human cellular promoters for gene-induced chondrogenesis of human bone marrow mesenchymal stem cells

High-expression plasmid vectors for human mesenchymal stem cells (MSCs) were constructed by combination of cytomegalovirus immediate-early enhancer with cellular promoters. MSCs transfected with the vector showed higher transgene production of a cytokine, which increased the differentiation level to chondrocytes.     

Aluminium alloy welding by CO2 laser using filler wire ‐AIN formation and aluminium alloy weldability

Based on literature sources and the author's own research, this article presents the current state of knowledge about composite coatings created by means of the plasma transfer method. The general characteristics of composite coatings and their strengthening mechanisms have been described. Methods of creating composite coatings by means of the plasma transfer method have also been discussed.