Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

Effects of Annealing on Dielectric Loss and Microstructure of Aluminum Nitride Ceramics

The effect of annealing on tan δ and microstructures of aluminum nitride (AlN) ceramics were explored. Yttria was added as a sintering additive to AlN powders, and the powders were pressureless-sintered at 1900°C for 2 h in a nitrogen flow atmosphere. In succession to sintering, AlN samples were annealed at 720, 970 and 1210°C for 2 and 4 h. Very low tan δ values between 2.6 and 6.0 × 10⁻⁴ at 28 GHz were obtained when the AlN samples were annealed for 4 h at all the annealing temperatures.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Synergic effect of Pd/γ-alumina and Cu/ZSM-5 on the performance of NO x storage reduction catalyst

NO _x reduction with a combination of catalysts, Pd catalyst, NO _x storage reduction (NSR) catalyst and Cu/ZSM-5 in turn, was investigated to elucidate for the high NO _x reduction activity of this catalyst combination under oxidative atmosphere with periodic deep rich operation. The catalytic activity was evaluated using the simulated exhaust gases with periodically fluctuation between oxidative and reductive atmospheres, and it was found that the NO _x reduction activity with this catalyst combination was apparently higher than that of the solely accumulation of these individual activities, which was caused by the additional synergic effect by this combination. The Pd catalyst upstream of the NSR catalyst improved NO _x storage ability by NO₂ formation under oxidative atmosphere. The stored NO _x was reduced to NH₃ on the NSR catalyst, and the generated NH₃ was adsorbed on Cu/ZSM-5 downstream of the NSR catalyst under the reductive atmosphere, and subsequently reacted with NO _x on the Cu/ZSM-5 under the oxidative atmosphere.     

Enantio-differentiating hydrogenation of prochiral ketones over modified nickel

This article reviews the enantio-differentiating hydrogenation of prochiral ketones over a asymmetrically modified catalyst, focusing on the hydrogenation of simple prochiral alkanones. The parameters affecting catalytic activity and enantiodifferentiating ability are considerable in number, and each parameter should be optimized in order to attain a highperformance enantio-differentiating catalyst. Optimization of the parameters and the mode of enantio-differentiation are discussed and compared with the enantio-differentiating hydrogenation of β-ketoesters.     

Plasma etching durability of poly(methyl methacrylate)

The decomposition of poly(methyl methacrylate) (PMMA), as a positive resist, in CF₄/O₂ plasma etching has been studied in the thin film state in order to clarify the factors influencing the dry etching durability of resists. It becomes clear that the major PMMA decomposition in CF₄/O₂ plasma etching proceeds by the mechanism of random chain scission because very small kinetic chain lengths are estimated from the gel permeation chromatography data. The Arrhenius plots for the plasma etching rate of PMMA bend above about the glass transition temperature (T_g), where rapid increase of the etching rate and remarkable pattern deformation are observed. Activation energy of the PMMA etching rate which is changed by oxygen concentration and rf power indicates various values from 3.1 to 6.5 kcal/mol below about T_g. The result of molecular weight variation in the cross section of the film suggests that the active species permeate into the film with fairly large speed and the PMMA decomposition occurs not only at the film surface but also at deep layer of the film.     

Continual conversion of free fatty acid in rice bran oil to triacylglycerol by immobilized lipase

Rice bran oil containing 30–50% free fatty acid was continually converted to an oil containing more than 75% of triacylglycerol (TG) by means of immobilized lipase. The reaction was carried out at 60°C for 24 h with dehydration and reactant mixing by dry nitrogen flow under a positive nitrogen atmosphere. Enzymatic TG synthesis with evaporation by heating was not suitable because of the increasing peroxide value of the oil. Part of this article was presented at the annual meeting of the Japan Oil Chemists' Society at Sendai, Japan, October, 16, 1990.     

Uniformly Porous Composites with 3-D Network Structure (UPC-3D) for High-Temperature Filter Applications

Uniformly porous composites with 3-D network structure (UPC-3D) have been recently developed via a pyrolytic reactive sintering process, which takes advantage of the evolved CO₂ gas from a decomposing carbonate source (e.g., dolomite, CaMg(CO₃)₂) and does not require any additional pore-forming agent nor long-time burning-out process. Through liquid formation via LiF doping, strong necks are formed between constituent particles before completion of the pyrolysis of carbonate, resulting in the formation of a strong 3-D network structure. The pore size distribution is very narrow (with typical pore size: ∼1 μm), and the porosity was controllable (∼30–60%) by changing the sintering temperature. This article presents the development details of UPC-3D, and reports the recent findings in CaZrO₃/MgAl₂O₄ system, which will be one of the more promising systems for practical applications.     

Synthesis of High Density and Transparent Forsterite Ceramics Using Nano-Sized Precursors and Their Dielectric Properties

Forsterite (Mg₂SiO₄) ceramics were prepared using Mg(OH)₂ and SiO₂ as precursors, and the effect of powder characteristics of Mg(OH)₂ on calcination and sintering was investigated. The use of highly dispersed Mg(OH)₂ powder (HD powder) resulted in a lower calcination temperature. Forsterite powder of high homogeneity and small particle size prepared from the HD powder enabled synthesis of high-density forsterite ceramics by ordinary sintering without applying external pressure. Moreover, transparent forsterite ceramics were successfully synthesized through addition of excess Mg to the precursors to compensate for Mg evaporated during the sintering process. Subsequent dielectric measurements revealed that the transparent forsterite ceramics had a very low dielectric loss (tan δ<10⁻⁴).     

Relation between crystal structure and lattice oxygen content of sintered reaction-bonded silicon nitride

When reaction-bonded silicon nitride containing MgO/Y₂O₃ additives is sintered at three different temperatures to form sintered reaction-bonded silicon nitride (SRBSN), the thermal conductivity increases with sintering temperature. The β-Si₃N₄ (silicon nitride) crystals of SRBSN ceramics were synthesized and characterized to investigate the relation between the crystal structure and the lattice oxygen content. The hot-gas extraction measurement result and the crystal structure obtained using Rietveld analysis suggested that the unit cell size of the β-Si₃N₄ crystal increases with the decrease in the lattice oxygen content. This result is reasonable considering that the lattice oxygen with the smaller covalent radius substitutes nitrogen with the larger one in the β-Si₃N₄ crystals. The lattice oxygen content decreased with increasing sintering temperature which also correlated with increase in thermal conductivity. Moreover, it is noteworthy from the viewpoint that it may be possible to apply the lattice constant analysis for the nondestructive and simple measurement of the lattice oxygen content that deteriorates the thermal conductivity of the β-Si₃N₄ ceramics.