Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

Preparation and mechanical properties of polystyrene–clay hybrids

Polystyrene–clay hybrids (PSCHs) were prepared by melt blending a styrene vinyloxazoline copolymer with organophilic clay. In the PSCHs, the silicate layers of the clay were delaminated and dispersed homogeneously to the nanometer level. The moduli of the PSCHs were higher than that of the PS copolymer. For example, the tensile modulus of the PSCH with 5 wt % clay was 1.4 times higher compared to that of the PS copolymer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3359–3364, 1999     

Mixing in multiple-impeller stirred tank reactors with boiling liquids

Mixing in a boil-off mechanically stirred tank reactor with multiple impellers was examined. Power consumption and gas hold-up were measured in boiling water in a 0.2 m i.d. stirred tank reactor with three four-pitched blade downflow disk turbines. Vapour was generated from both the immersed ring heater and the impellers. At low vapour generation rates, vapour was mainly generated from the impellers rather than from the heater, whereas nucleation occurred at the heater instead of the impeller at higher vapour generation rates. The mechanical power consumption decreased due to vapour generation. The change in boiling-to-non-boiling mechanical power ratio with varying impeller rotational speed and boiling rate was complicated and not monotonous except at higher impeller speeds and boiling rates. The gas hold-ups increased with increasing vapour generation rate but were rather small as compared to those in cold gas dispersing systems. Empirical correlations for power consumption and gas hold-up in boiling liquids were developed using the present experimental data.     

Effect of skimmed milk and its fractions on the inactivation of Escherichia coli K12 by high hydrostatic pressure treatment

We investigated the effects of skimmed milk and its protein fractions (casein, whey, globulin, and albumin) on the injury and inactivation of Escherichia coli K-12 by high hydrostatic pressure (HHP) treatment. The protective effect of skimmed milk on HHP-mediated inactivation and injury of E. coli increased with increases in the skimmed milk concentration. However, protein fractions derived from skimmed milk did not exhibit this protective effect. Microscopy analysis by DAPI/PI staining indicated that some cells were localized in the solid portion of skimmed milk, and some of these cells were alive. The coagulated fraction derived from the autoclaved whey fraction also showed a significant protective effect. We speculate that the solid portion in skimmed milk could provide the protective effect to bacterial cells.     

Effect of light intensity and frequency of flashing light from blue light emitting diodes on astaxanthin production by Haematococcus pluvialis

Flashing light from blue light emitting diodes is an effective method for the reduction of energy consumption in the bioproduction of astaxanthin by Haematococcus pluvialis. We investigated the effects of light intensity and frequency on the final astaxanthin concentration in bioproduction by H. pluvialis grown mixotrophically. The final astaxanthin concentration under illumination with flashing light, with frequencies ranging from 25 to 200 Hz, was dependent on the light intensity and on the duty cycle and was equivalent, or higher, in comparison with that under illumination with continuous light at the same incident intensity. The light intensity determined the maximum attainable concentration of astaxanthin under continuous illumination. Under illumination with flashing light, the ratio of the final astaxanthin concentration to the maximum concentration at a specific light intensity was correlated to the duty cycle in the frequency range from 25 to 200 Hz. The effect of lower frequencies on enhanced astaxanthin production under flashing light was also studied; at levels as low as 1 Hz, higher final astaxanthin concentrations were observed under flashing light compared to concentrations attained under continuous light.     

An ultra-fast fabrication technique for anode support solid oxide fuel cells by microwave

An effective and facile technique has been developed for high temperature anode-electrolyte co-sintering of anode support solid oxide fuel cells by using microwave activated sparking plasma. A high sintering temperature of 1600 °C can be achieved in a few minutes time by discharging effect. Anode support substrate pellet is uniaxially pressed, and then dip-coated with a 10 μm yttria stabilized zirconia electrolyte layer. After the microwave co-sintering, La_0.8Sr_0.2MnO_x cathode is screen-printed onto electrolyte and sintered by conventional thermal method. The cell has stably operated in 3% humidified hydrogen for more than 130 h.     

Preparation and electrocatalytic activity of palladium-platinum core-shell nanoalloys protected by a perfluorinated sulfonic acid ionomer

Palladium-platinum nanoalloys with a core-shell and nano-network structure were successfully synthesized by a hydrogen sacrificial protective method in an aqueous solution directly using a perfluorinated sulfonic acid (PFSA) ionomer as a protecting agent. The structure, local composition and electrocatalytic activity for the oxygen reduction reaction of the Pd/Pt/PFSA nanoalloys were investigated by transmission electron microscopy (TEM), aberration corrected scanning transmission electron microscopy (Cs-STEM), energy-dispersive X-ray spectrometry (EDS) and voltammetry. The core-shell structure was completed without contaminating reducing agents, organic solvents, useless protecting agents and a mediator. The Pd/Pt/PFSA core-shell nanoalloys realized a high electrochemical surface area and better electrocatalytic mass-activity for the oxygen reduction reaction than the Pt/PFSA nanoparticles.     

Limiting current density in bis(trifluoromethylsulfonyl)amide-based ionic liquid for lithium batteries

The physicochemical and electrochemical properties of the binary ionic liquid (IL), lithium bis(trifluoromethylsulfonyl)amide (LiTFSA) dissolved in N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoromethylsulfonyl)amide (DEMETFSA), were investigated. The ionic conductivity of the binary IL decreased with an increase in LiTFSA concentration. The self-diffusion coefficients of Li⁺, DEME⁺, and TFSA⁻ dissolved in the IL were measured by using the pulsed-field-gradient spin-echo (PGSE) NMR method. The self-diffusion coefficient of each ionic species was also found to decrease with increasing concentration of LiTFSA. The limiting current density in the IL electrolyte was evaluated by chronoamperometry using symmetric Li|IL|Li cell. The results suggest that the diffusion process of Li(I) in the IL dominates the limiting current density in the cell. The highest limiting current density is achieved at a concentration of 0.64 mol dm⁻³ of LiTFSA.     

Bulk heterojunction organic solar cells utilizing 1,4,8,11,15,18,22,25-octahexylphthalocyanine

Bulk heterojunction solar cells utilizing soluble phthalocyanine derivative, 1,4,8,11,15,18,22,25-octahexylphthalocyanine (C6PcH₂) have been investigated. The active layer was fabricated by spin-coating the mixed solution of C6PcH₂ and 1-(3-methoxy-carbonyl)-propyl-1-1-phenyl-(6,6)C61 (PCBM). The photovoltaic properties of the solar cell with bulk heterojunction of C6PcH₂ and PCBM demonstrated the strong dependence of active layer thickness, and the optimized active layer thickness was clarified to be 120 nm. By inserting MoO₃ hole transport buffer layer between the positive electrode and active layer, the FF and energy conversion efficiency were improved to be 0.50 and 3.2%, respectively. The tandem organic thin-film solar cell has also been studied by utilizing active layer materials of C6PcH₂ and poly(3-hexylthiophene) and the interlayer of LiF/Al/MoO₃ structure, and a high V_oc of 1.27 V has been achieved.