Investigation of Ozone Concentration Measurement by Visible Photo Absorption Method

The measurement of ozone concentration based on the visible photo absorption method is investigated. An LED having an emission peak at 609 nm and a photo diode sensitive at visible light frequencies are used as the light source and the photo detector, respectively. The transmittance is measured as a function of ozone concentration, which is in reasonable agreement with the Beer–Lambert relationship. The effective absorption cross-section can therefore be estimated from the fitting procedure. The concentrations determined by both the UV and visible photo absorptions agree well with each other in the range from 7.1 to 68.4 g/m³(N). The relative error in these concentrations is discussed on the basis of the Twyman–Lothian curve. The ozone measurement for the air-fed ozone generation is also investigated. The effect of photo absorption due to NOx species is unavoidable. The present results provide useful data if the ozone measurement based on the visible photo absorption method is applied to ozone monitoring instruments or used for laboratory experiments.     

Effects of Ozone-Gas Bubble Size and pH on Ozone/UV Treatment

A series of ozone/UV treatment under injection of ozone with different ozone-gas bubble sizes was performed at pH 1.7 and 7.4. The increase in the bubble size and the decrease in pH enhanced the ozone utilization efficiency. The enhancement of ozone utilization efficiency was caused by the shift of the production pathway of hydroxyl radical (OH) from the OH production via O₃ ^– to the UV photolysis of H₂O₂. The lower pH caused this shift through the chemical equilibrium of H₂O₂ and HO₂ ^–, and the large bubbles caused this shift through the augmentation of H₂O₂ transport from the bubble surface to the bulk solution.     

采用MAMMOS技术的高密度光记录

MAMMOS(Magnetic Amplifying Magneto－ Optical System:磁畴扩大磁光系统 )是实现高密度磁光盘的有效方法。不仅能得到不依赖于磁畴长度的较大的读出信号振幅,而且还能实现超出光学系统衍射极限的分辨率。过去,为实现磁畴的复印与扩大,要对记录膜面施加垂直方向的外部磁场。而现在得知,同时施加垂直磁场和水平方向的磁场,可大幅度地提高微小磁畴的读出特性。确认采用施加水平磁场的方法,在λ =635 nm, NA=0.55的条件下, 0.15μ m的连续磁畴也能获得 BER=2× 10－ 4的读出效果。     

Spray-dry synthesis of β-Cu1.8Zn0.2V2O7 ceramic fine particles showing giant negative thermal expansion

We used spray-dry method to synthesize fine powder of β-Cu_1.8Zn_0.2V₂O₇ showing large negative thermal expansion (NTE) linearly to temperature over a wide temperature range. The NTE of β-Cu_1.8Zn_0.2V₂O₇ is produced by microstructures consisting of voids and anisotropic thermal deformation of crystal grains in ceramics. By reducing the size of the microstructures that produce NTE, large NTE equivalent to that of bulk was realized, even for ceramic particles of about 2 μm size. Comparison with particles produced using a conventional method demonstrates that the particle size distribution is narrow and that the particles are nearly spherical. This achievement is expected to pave the way to use of NTE materials in micrometer-scale control of thermal expansion.     

Matrix influence on the piezoelectric properties of piezoelectric ceramic/polymer composite exhibiting particle alignment

This study was addressed to the influence of an electric field strength applied at fabrication process and matrix properties, such as the dielectric constant and the Young's modulus, on “pseudo‐1‐3 piezoelectric ceramic/polymer composite” in order to further enhance the piezoelectricity of that. The pseudo‐1‐3 piezoelectric ceramic/polymer composite consists of linearly ordered piezoelectric ceramic particles in polymer material. Silicone gel, silicone rubber, urethane rubber, and poly‐methyl‐methacrylate, which exhibit different dielectric constants and Young's modulus, were used as matrices to evaluate the matrix influence. The piezoelectricity of the pseudo‐1‐3 piezoelectric ceramic/polymer composite was evaluated using the piezoelectric strain constant d₃₃. The d₃₃ is one of the indices of the piezoelectric properties for piezoelectric materials. As a result, it was confirmed that d₃₃ of the pseudo‐1‐3 piezoelectric ceramic/polymer composite increased with the increase of the electric filed strength applied at fabrication process, though, it reached a constant value at a certain strength value. Further it was confirmed that dielectric constant of the matrix had a small influence on d₃₃ of the pseudo‐1‐3 piezoelectric ceramic/polymer composite, however, in case of matrix of lower Young's modulus, d₃₃ was increase. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41817.     

Nickel‐Catalyzed Suzuki–Miyaura Coupling of a Tertiary Iodocyclopropane with Wide Boronic Acid Substrate Scope: Coupling Reaction Outcome Depends on Radical Species Stability

We describe a nickel‐catalyzed Suzuki–Miyaura arylation of a tertiary iodocyclopropane with arylboronic acids; this is an efficient and convergent strategy for providing various enantioenriched arylcyclopropanes with a quaternary stereogenic center. This is the first metal‐catalyzed coupling between a tertiary alkyl electrophile and a wide range of aromatics, including heteroaromatics. We found that the outcome of the Ni‐catalyzed coupling with halides as electrophiles was dependent on the stability of the radical species formed during the reaction. The use of tert‐butyl alcohol (t‐BuOH) as the reaction solvent was very effective, because of its stability under the radical‐generating reaction conditions.

     

Characteristics of fluoride adsorption onto aluminium(III) and iron(III) hydroxide flocs

The fluoride adsorption onto the hydroxide flocs of Al(III), Fe(III), or a mixture of the two was studied. The optimum pH was influenced by the flocs’ solubility and surface charge. Although the Al(III) hydroxide flocs had a maximum adsorption capacity at the equilibrium concentration of 8 mg-F/L, the two-stage adsorption process revealed that the mixture of the Al(III) and Fe(III) hydroxide flocs required the smallest adsorbent dose as the concentration changed from 40 to 8 mg-F/L. Thus, the simultaneous dosing of Al(III) and Fe(III) combined with a two-stage adsorption process appears to be an effective option for fluoride removal.     

Finite element polycrystal model simulation of cold rolling textures in deformation processed two-phase Nb／Al metal-metal composites

The finite element polyerystal model (FEPM) was extended and applied to simulate the development of the cold rolling textures of matrix aluminum in deformation processed two-phase 10% and 20% Nb/Al(in volume fraction) metal-metal composites on the basis of slip deformation of individual grains. This simulation method can assure the continuity of stress and displacement at the boundary during heterogeneous deformation and take arbitrary boundary conditions into consideration. The starting hot-extruded textures, as initial input condition, were taken into account in the FEPM simulation. The simulation results show that the main texture components and their evolution after various cold rolling reductions in 10% and 20% Nb/Al metal-metal composites are well qualitatively in agreement with the experimental ones. The initially extruded textures are rather weak, so they have no much influence on the simulated final cold rolling textures of the matrix aluminum for Nb/Al composites.     

Cholelithiasis in hamsters: Effects of cholic acid and calcium on gallstone formation

Dietary cholic acid (0.1%) and/or calcium (2.6% as calcium carbonate) were added to a semipurified diet containing cholesterol and ethynyl estradiol to determine whether the incidence of pigment and/or cholesterol gallstones would be changed. Male golden Syrian hamsters were fed the experimental diets for 96 days (Group 1, control; Group 3, cholic acid plus calcium) or only an average of 60 days (Group 2, 0.1% cholic acid). Animals in Group 2 became ill (weight loss, low food intake, diarrhea) possibly due to cholic acid (or deoxycholic acid) toxicity. Cholesterol gallstones and crystals were absent in all experimental groups. The incidence of pigment gallstones was: control, Group 1, 12/16; 0.1% cholic acid, Group 2, 3/13; and 0.1% cholic acid plus calcium, Group 3, 11/22. Cholic acid with or without calcium produced an elevation of both liver and plasma cholesterol: Group 2, 80.1 mg/g and 501 mg/dl; Group 3, 103.7 mg/g and 475 mg/dl vs Group 1, 65 mg/g and 209 mg/dl, respectively. The lithogenic indices of the bile were lower in Groups 2 and 3 compared to Group 1, controls, 0.45 and 0.58 vs 1.16, respectively. The extent of the portal tract pathology could not be correlated with the presence or absence of pigment gallstones or with the levels of lithocholic acid in the hamster bile. In summary, when semipurified diets were supplemented with ethynyl estradiol and cholic acid, with and without calcium supplementation, no cholesterol gallstones formed and the incidence of pigment gallstones was not altered.     

Controllable electrode activities of nano-carbon films while maintaining surface flatness by electrochemical pretreatment

A carbon film consisting nanocrystallites with mixed sp² and sp³ bonds formed by using the electron cyclotron resonance (ECR) sputtering method was studied with respect to the changes in characteristics caused by electrochemical pretreatment (ECP). Unlike glassy carbon, our sputtered nanocrystalline carbon film deposited at an acceleration voltage of 75 V (ECR-75 nano-carbon film) largely retained its surface flatness after the ECP. This robust surface could be caused by an increase of 42% in the sp³ carbon realized by increasing the acceleration voltage during sputtering. The electrode activity of ECR-75 nano-carbon film was improved for surface sensitive species including Fe^3+/2+ unlike the boron doped diamond (BDD) electrode. This is because a sufficient quantity of surface sp² bonds remained and because the introduction of surface oxygen-containing groups is more efficient than with the BDD electrode. With pretreated ECR-75 nano-carbon film, the peak potential of glutathione was reduced solely due to the increase in the surface hydrophilicity with a sufficient quantity of surface sp² bonds, thus achieving the lowest detection limit (0.4 μM) ever obtained with carbon electrodes. We also achieved the stable measurement of 30 μM of serotonin (20 times) without the electrode surface fouling found with other electrodes.