Influence of Specific Surface Area of Aluminium Powder on the reactivity of aluminium/ammonium perchlorate composition

Aluminium/ammonium perchlorate (40/60 wt.%) is a pyrotechnic composition widely used as an igniter charge for small calibre rocket motors. Five different types of aluminium powders with specific surface area varying from 0.52 m²/g to 6.00 m²/g have been studied to evaluate the influence of specific surface area on the ignition characteristics of the charge. While the peak pressure varies from 35.5 ksc to 54.5 ksc (0.30 g in 48.0 cm³ vol.), the corresponding time to P_max varies from 11.2 ms to 1.6 ms showing higher reactivity of the mix with increase in aluminium surface area. This order of reactivity agrees with the order of reactivity determined from the DTG curves of the metal oxidation by comparing the peak height to half width ratio. However, the total gas generated by all the charges is approximately the same and the difference in peak pressure is caused by the difference in the rate of reaction and after about 30 ms all the compositions exhibit the same order of temperature and pressure. The charge has got an ignition temperature of about 640 K and the ignition is preceded by the exothermic decomposition of ammonium perchlorate. The activation energy varies from 92.2 kJ/mol to 127.6 kJ/mol and the corresponding pre-exponential factor from 9.7 × 10⁶ min⁻¹ to 7.1 × 10⁹ min⁻¹ and they exhibit the kinetic compensation effect with an isokinetic temperature of 647 K.     

Investigation of Mechanical Properties and Dry Sliding Wear Behaviour of Squeeze Cast LM6 Aluminium Alloy Reinforced with Copper Coated Short Steel Fibers

LM6 aluminium alloy with 2.5–10 wt% of copper coated short steel fiber reinforced composites were prepared using squeeze casting process. Microstructure and mechanical properties viz., hardness, tensile strength and ductility were investigated. Dry sliding wear behaviour was tested by considering sliding distance and load. Fracture surface and worn surface were examined using field emission scanning electron microscope (FESEM). Hardness of composites increased with increasing wt% of fiber. Tensile strength of composites increased up to 19% for 5 wt% fiber composites. Further addition of fibers decreased the tensile strength of composites. Ductility of the composites decreased with the addition of fibers into the matrix. Wt% of fibers significantly decreased the weight loss, coefficient of friction and wear rate. Also the cumulative weight loss decreased up to 57% for 10 wt% of composites compared to LM6 aluminium alloy. Fracture surface of composite tensile specimen showed dimple formation and fiber pullout. Worn surface of matrix showed long continuous grooves due to local delamination on the surface. However, worn surface of composites showed fine and smooth grooves due to ploughing rather than local delamination. Copper coated steel fiber reinforcement in LM6 aluminium alloy exhibited better mechanical properties and wear resistance compared to matrix.     

A partition of unity‐based ‘FE–Meshfree’ QUAD4 element for geometric non‐linear analysis

The recently published ‘FE–Meshfree’ QUAD4 element is extended to geometrical non‐linear analysis. The shape functions for this element are obtained by combining meshfree and finite element shape functions. The concept of partition of unity (PU) is employed for the purpose. The new shape functions inherit their higher order completeness properties from the meshfree shape functions and the mesh‐distortion tolerant compatibility properties from the finite element (FE) shape functions. Updated Lagrangian formulation is adopted for the non‐linear solution. Several numerical example problems are solved and the performance of the element is compared with that of the well‐known Q4, QM6 and Q8 elements. The results show that, for regular meshes, the performance of the element is comparable to that of QM6 and Q8 elements, and superior to that of Q4 element. For distorted meshes, the present element has better mesh‐distortion tolerance than Q4, QM6 and Q8 elements. Copyright © 2009 John Wiley & Sons, Ltd.     

Development and validation of the College Life Alcohol Salience Scale: A measure of beliefs about the role of alcohol in college life.

This article reports the development and validation of the College Life Alcohol Salience Scale (CLASS), which assesses college students’ beliefs about the centrality of alcohol to the college experience. Developed using procedures designed to increase its ecological validity, the CLASS was administered to three samples of college students (total N = 571). Its unidimensional factor structure was first established via exploratory factor analysis and parallel analysis on one sample and then verified via confirmatory factor analysis on a separate sample. Scores on the CLASS were predictably related to a nomological network of drinking and personality variables and it provided incremental validity in accounting for drinking frequency and amount, when added to drinking motive scores. The importance of assessing and developing interventions to target the types of beliefs measured by the CLASS is discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Enzymatic saccharification and fermentation of paper and pulp industry effluent for biohydrogen production

Paper and pulp industry effluent was enzymatically hydrolysed using crude cellulase enzyme (0.8–2.2FPU/ml) obtained from Trichoderma reesei and from the hydrolysate biohydrogen was produced using Enterobacter aerogenes. The influence of temperature and incubation time on enzyme production was studied. The optimum temperature for the growth of T. reesei was found to be around 29 °C. The enzyme activity of 2.5 FPU/ml was found to produce about 22 g/l of total sugars consisting mainly of glucose, xylose and arabinose. Relevant kinetic parameters with respect to sugars production were estimated using two fraction model. The enzymatic hydrolysate was used for the biohydrogen production using E. aerogenes. The growth data obtained for E. aerogenes were fitted well with Monod and Logistic equations. The maximum hydrogen yield of 2.03 mol H₂/mol sugar and specific hydrogen production rate of 225 mmol of H₂/g cell/h were obtained with an initial concentration of 22 g/l of total sugars. The colour and COD of effluent was also decreased significantly during the production of hydrogen. The results showed that the paper and pulp industry effluent can be used as a substrate for biohydrogen production.     

Effect of the Strain Rate and Microstructure on Damage Growth in Aluminum

Materials used in soldier protective structures, such as armor, vehicles and civil infrastructures, are being improved for performance in extreme dynamic environments. Nanocrystalline metals show significant promise in the design of these structures with superior strengths attributed to the dislocation-based and grain-boundary-based processes as compared to their polycrystalline counterparts. An optimization of these materials, however, requires a fundamental understanding of damage evolution at the atomic level. Accordingly, atomistic molecular dynamics simulations are performed using an embedded-atom method (EAM) potential on three nano-crystalline aluminum atom systems, one a Voronoi-based nano-crystalline system with an average grain size of 10 nm, and the other two single crystals. These simulations are performed under the condition of uniaxial expansion at several strain rates ranging from 10⁶s^-1 to 10¹⁰s^-1. Results for the effective stress are discussed with the aim of establishing the role of the strain rate and microstructure on the evolution of the plastic strain and void volume fraction and the eventual loss of stress carrying capability of the atom systems.     

Bacterial Ecology of Fermented Cucumber Rising pH Spoilage as Determined by Nonculture‐Based Methods

Fermented cucumber spoilage (FCS) characterized by rising pH and the appearance of manure‐ and cheese‐like aromas is a challenge of significant economical impact for the pickling industry. Previous culture‐based studies identified the yeasts Pichia manshurica and Issatchenkia occidentalis, 4 Gram‐positive bacteria, Lactobacillus buchneri, Lactobacillus parrafaraginis, Clostridium sp., and Propionibacterium and 1 Gram‐negative genus, Pectinatus, as relevant in various stages of FCS given their ability to metabolize lactic acid. It was the objective of this study to augment the current knowledge of FCS using culture‐independent methods to microbiologically characterize commercial spoilage samples. Ion Torrent data and 16S rRNA cloning library analyses of samples collected from commercial fermentation tanks confirmed the presence of L. rapi and L. buchneri and revealed the presence of additional species involved in the development of FCS such as Lactobacillus namurensis, Lactobacillus acetotolerans, Lactobacillus panis, Acetobacter peroxydans, Acetobacter aceti, and Acetobacter pasteurianus at pH below 3.4. The culture‐independent analyses also revealed the presence of species of Veillonella and Dialister in spoilage samples with pH above 4.0 and confirmed the presence of Pectinatus spp. during lactic acid degradation at the higher pH. Acetobacter spp. were successfully isolated from commercial samples collected from tanks subjected to air purging by plating on Mannitol Yeast Peptone agar. In contrast, Lactobacillus spp. were primarily identified in samples of FCS collected from tanks not subjected to air purging for more than 4 mo. Thus, it is speculated that oxygen availability may be a determining factor in the initiation of spoilage and the leading microbiota.     

The effect of three low-cost engineering treatments on driver fatigue: A driving simulator study

Three engineering treatments were implemented in a driving simulator study to assess the effect of road-based measures on alleviating the symptoms of fatigue. Using results from previous research on the effect of circadian rhythms on fatigue-related crashes, two groups of male drivers were recruited for this study: young shift workers under the age of 35, who attended immediately after their night shift, and older drivers over the age of 45, who completed the study during the ‘post lunch dip’ period, after consuming lunch. Eye tracking (PERCLOS) and lateral driver performance measures were used to assess whether baseline measures of fatigue changed after drivers experienced each of the three treatments, which included variable message signs, chevrons and rumble strips. Results showed a marked difference in these measures between drivers’ baseline (not fatigued) and experimental (fatigued) visits. There were also some reductions in lateral deviation and eye closure (as measured by PERCLOS) when the treatments were encountered, but no marked difference between the three treatments. These results suggest that in addition to driver- and vehicle-based methods currently employed to mitigate the effects of fatigue, the inclusion of such engineering measures may help alleviate fatigue-related impairments in driving, particularly if such treatments are implemented during long stretches of straight monotonous roads which are known to be associated with fatigue-related crashes. However, positive effects of the treatments were short lived, prompting the need for further investigations on their optimal frequency of presentation and combination to achieve maximum impact from these low-cost, road-based treatments.     

Influence of surface modification on the apatite formation and corrosion behavior of Ti and Ti-15Mo alloy for biomedical applications

Commercially pure Ti and Ti-15Mo specimens were subjected to alkali-hydrogen peroxide and subsequent heat treatment to produce a nanoporous titanate gel layer with anatase phase. The surface morphology of the untreated, alkali-hydrogen peroxide treated and alkali-hydrogen peroxide heat treated specimens before and after 7 days of immersion in simulated body fluid was characterized using X-ray Diffractometer (XRD), Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FT-IR). The formation of nanoporous titanate gel layer and the growth of apatite layer over the surface modified specimens after 7 days of immersion in simulated body fluid were confirmed. Further, the electrochemical corrosion behavior of all the specimens was examined using potentiodynamic polarization and electrochemical impedance spectroscopic techniques.