Release of stored thermochemical energy from dehydrated salts

Thermochemical materials, particularly salt hydrates, have significant potential for use in thermal energy storage applications. When a salt hydrate is heated to a threshold temperature, a chemical reaction is initiated to dissociate it into its anhydrous form and water vapor. The anhydrous salt stores the sensible energy that was supplied for dehydration, which can be later extracted by allowing cooler water or water vapor to flow through the salt, transforming the stored energy into sensible heat. We model the heat release that occurs during a thermochemical hydration reaction using relations for mass and energy conservation, and for chemical kinetics and stoichiometry. A set of physically significant dimensionless parameters reduces the number of design variables. Through a robust sensitivity analysis, we identify those parameters from this group that more significantly influence the performance of the heat release process, namely a modified Damköhler number, the thermochemical heat capacity, and the heat flux and flowrate. There is a strong nonlinear relationship between these parameters and the process efficiency. The optimization of the efficiency with respect to the parameters provides guidance for designing engineering solutions in terms of material selection and system properties.     

An algorithm for the kinetics of tire pyrolysis under different heating rates

Tires exhibit different kinetic behaviors when pyrolyzed under different heating rates. A new algorithm has been developed to investigate pyrolysis behavior of scrap tires. The algorithm includes heat and mass transfer equations to account for the different extents of thermal lag as the tire is heated at different heating rates. The algorithm uses an iterative approach to fit model equations to experimental data to obtain quantitative values of kinetic parameters. These parameters describe the pyrolysis process well, with good agreement (r² > 0.96) between the model and experimental data when the model is applied to three different brands of automobile tires heated under five different heating rates in a pure nitrogen atmosphere. The model agrees with other researchers’ results that frequencies factors increased and time constants decreased with increasing heating rates. The model also shows the change in the behavior of individual tire components when the heating rates are increased above 30 K min⁻¹. This result indicates that heating rates, rather than temperature, can significantly affect pyrolysis reactions. This algorithm is simple in structure and yet accurate in describing tire pyrolysis under a wide range of heating rates (10–50 K min⁻¹). It improves our understanding of the tire pyrolysis process by showing the relationship between the heating rate and the many components in a tire that depolymerize as parallel reactions.     

Erosion of atmospheric plasma sprayed rare earth oxide coatings under air suspended corundum particles

Atmospheric plasma sprayed (APS) zirconium oxide based coatings are used widely in aero engine components for providing thermal insulation, improving the corrosion and oxidation resistance. Despite its wide spread industrial use, little is known about the basic erosion behaviour and the mechanisms by which such coatings erode. In this paper, the erosive wear behaviours of Yttria Stabilized Zirconia (YSZ) coatings; Lanthanum Zirconate (LZ) coatings and Inconel 738 base material (BM) were studied and compared under air jet erosion conditions with corundum particles as erodent material. The erosion behaviour was studied with respect to the different porosity volume percentages of the coatings and the changes in velocity of erodent, impact angle of erodent and erodent particle flux. It was found that in solid particle erosion, the wear resistances of YSZ and LZ coatings were the best at their lowest porosity volume and it decreased with the increase in the percentage volume of porosity. There was a linear increase in the wear resistance with the increase in hardness. Further, relationships among the erosion parameters with respect to erosive wear loss were derived by using the response surface methodology and the erosion mechanisms were discussed adequately.     

Control of dynamic overvoltages due to load rejection by static shunt compensation

A digital computer method used to evaluate the performance of a static shunt compensator as a device for controlling dynamic overvoltages caused by load rejection is presented. A typical system of a generating station connected to a load centre through an EHV transmission line with a static compensator at the load end is considered, and the envelopes of dynamic overvoltages following load rejection are evaluated. Detailed mathematical models incorporating the dynamics of a synchronous machine, transmission network and static shunt compensator are employed in the analysis. The static shunt compensator is shown to be an effective tool for controlling dynamic overvoltages. The application of this analysis for choosing an economic voltage rating of the surge arrestor is highlighted.     

A test of metabolically efficient coding in the retina

We tested the hypothesis that aspects of the neural code of retinal ganglion cells are optimized to transmit visual information at minimal metabolic cost. Under a broad ensemble of light patterns, ganglion cell spike trains consisted of sparse, precise bursts of spikes. These bursts were viewed as independent neural symbols. The noise in each burst was measured via repeated presentation of the visual stimulus, and the energy cost was estimated from the total charge flow during ganglion cell spiking. Given these costs and noise, the theory of efficient codes predicts an optimal distribution of symbol usage. Symbols that are either noisy or costly occur less frequently in this optimal code. We found good qualitative and quantitative agreement with the measured distribution of burst sizes for ganglion cells in the tiger salamander retina.     

Extrusion of alumina fibre using sol-gel precursor

Alumina fibres were prepared by extrusion using boehmite sol as binder. The microstructure and mechanical properties of the fibres were studied. The fibres sintered at 1400 oC have relatively dense microstructure and the highest strength.