Effect of oxygenation on electrocatalysis of La0.6Ca0.4CoO3−x in bifunctional air electrode

A vacuum-annealed La_0.6Ca_0.4CoO_3−x was consecutively oxygenated in air at temperatures decreasing from 800 to 100 °C, and its electrocatalytic activities for oxygen reduction and evolution were then measured as a function of the oxygenation temperature. The valence of Co cation, changing between +2 and +3, was found susceptible to annealing either in vacuum or air. The catalytic activities initially decrease monotonically as the oxygenation temperature was decreased from 800 to 300 °C, as a result of increasing oxygen content, and then rise abruptly with the oxygen reduction activity reaching a maximum at 200 °C and the oxidation activity at 150 °C. X-ray photoelectron spectroscopy analysis indicated that the enhancements by the low-temperature oxygenation involved increased OH coverage and less charged cations at surface. The results clearly reveal the importance of the post-calcination annealing process for optimizing the performance of La_0.6Ca_0.4CoO_3−x in air electrode applications.     

一种微透镜阵列的研制

介绍一种利用表面张力的作用、以光纤作材料、用分离的自聚焦透镜制作微透镜阵型的方法，这种方法具有制作工艺简单、无须昂贵设备等优点，用此方法实际制作了具有良好连续面型的微透镜阵列，并对制作的微透镜阵列进行了测试，效果较好。     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

洼60-H26水平井套铣打捞技术

洼60-H26井是一口中曲率水平井,设计井深1 922 m,由于地面条件的限制,设计采用三维井眼轨道。该井水平段在钻至井深1 801 m时,发生卡钻事故。在卡钻事故处理过程中,采用测卡、爆炸松扣技术取出上部钻具后,应用了不同规格的套铣管对被卡钻具进行套铣,采用间歇式套铣方式实现了大斜度井段(45°-90°)的安全套铣,采用短套铣管完成了时水平井段内φ215．0 mm稳定器的套铣,采用φ228．6 mm套铣管成功套铣水平井段被卡LWD仪器,最后通过震击器震击成功解卡。详细介绍了洼60-H26水平井卡钻事故的处理过程,分析了在水平段处理卡钻事故的难点。该井处理卡钻事故的经验,对以后水平井施工中处理井下事故、打捞贵重仪器具有借鉴价值。     

Retrograde Amnesia Induced by Drugs Acting on Different Molecular Systems.

The gamma aminobutyric acid-A (GABAA) agonist, muscimol, the glutamate N-methyl-D-aspartate (NMDA) receptor antagonist, D-2-amino-5-phosphonopentanoic acid (AP5), and the inhibitor of the extracellularly regulated kinases (ERKs), UO 126, cause retrograde amnesia when administered to the hippocampus. In the present study, the authors found that they all cause retrograde amnesia for 1-trial inhibitory avoidance, not only when infused into the dorsal CA1 region of the hippocampus, but also when infused into the basolateral amygdala or the entorhinal, parietal, and posterior cingulate cortices. The posttraining time course of the effect of each drug was, however, quite different across brain structures. Thus, in all of them, NMDA receptors and the ERK pathway are indispensable for memory consolidation, and GABAA receptor activation inhibits memory consolidation: but in each case, their influence is interwoven differently. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

布帮鞋无浆贴合工艺技术

本工艺是对原有工艺的改进，突破了原有布帮鞋不能采用无浆贴合的局限性，对原有工艺中的不足有了很大的改进，提高了生产效率，改善了鞋子外观质量，增加了鞋子的美观性。     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

射频板条CO_2激光器并联谐振技术的研究

本文利用周期性网络模型计算了射频板条CO2激光器电极的纵向电压分布．探讨了并联谐振技术在板条器件中获得成功运用的原因．提出了利用并联谐振技术进一步提高电压分布均匀性的两个途径．