Reaction stoichiometry between TiCl3 and NaAlH4 in Ti-doped alanate for hydrogen storage: The fate of the titanium species

In order to understand the final state of the TiCl₃ dopant during the dehydrogenation and rehydrogenation cycles of NaAlH₄, we determined the reaction stoichiometry between TiCl₃ and NaAlH₄ by measuring the amount of hydrogen evolution from NaAlH₄ with the varying TiCl₃ -load. We found that: (i) TiCl₃ reacted with 3 M equivalents of NaAlH₄ during the doping process of ball-milling, (ii) the Ti dopant continued to react with NaAlH₄ during the first dehydrogenation process until total six equivalents of NaAlH₄ were consumed, and (iii) Ti fixed Al, not NaH, so that Al became insufficient during the rehydrogenation process. These findings lead to the conclusion that the reaction stoichiometry between Ti and Al is 1:6, which probably yields TiAl₆ and plays a catalytic role in the hydrogen storage reactions of Ti-doped NaAlH₄.     

Characteristics of transient vortices in the boundary layer on a rotating disk under orbital motion

The objective of this study is to experimentally examine the characteristics of transient vortices in the boundary layer on a disk undergoing both rotation and orbital motion. The velocity fluctuations on a rotating, orbiting disk （disk radius equal to orbital radius） are measured by the hot-wire method, and the effects of orbital motion on the transient vortices in the boundary layer are examined. When the ratio of the orbital speed to the speed of rotation is i-0.025, the interval of transient vortices depends on only the orbital radius, regardless of the directions of rota- tion and orbital motion. The rate of low-frequency disturbances increases as the orbital speed increases, and the vortices induced by these low-frequency disturbances travel over the disk and then develop in the region of in- creased velocity. Consequently, no vortices generated on a rotating disk under orbital motion are stationary rela- tive to the disk.     

Effect of catch cup geometry on 3D boundary layer flow over the wafer surface in a spin coating

Recently, development of high technology has been required for the formation of thin uniform film in manufacturing processes of semiconductor as the semiconductor instruments become more sophisticated. Spin coating is usually used for spreading photoresist on a wafer surface. However, since rotating speed of the disk is very high in spin coating, the dropped photoresist scarers outward and reattaches on the film surface. A catch cup is set up outside the wafer in spin coating, and scattered photoresist mist is removed from the wafer edge by the exhaust flow generated at the gap between the wafer edge and the catch cup. In the dry process of a spin coating, it is a serious concern that the film thickness increases near the wafer edge in the case of low rotating speed. The purpose of this study is to make clear the effect of the catch cup geometry on the 3D boundary layer flow over the wafer surface and the drying rate of liquid film.     

In-situ monitoring of surface stoichiometry and growth kinetics study of GaN (0001) in MOVPE by spectroscopic ellipsometry

GaN surface stoichiometry and growth kinetics in MOVPE were studied by in-situ spectroscopic ellipsometry. The effect of MOVPE conditions on both the surface stoichiometry and growth kinetics was investigated. The surface stoichiometry, such as N-rich, Ga-rich and Ga-excess surfaces, was monitored, and was drastically changed by the variation of the NH₃ partial pressure. When the TMG supply was interrupted during the growth, the layer-by-layer decomposition/revaporation was observed in H₂/NH₃ ambient. The decomposition rate was measured as a function of the NH₃ flow rate at the conventional epilayer growth temperatures (1050–1140 C). The decomposition rate was decreased with the increase in the N coverage on the GaN surface. it was found that the surface stoichiometry is a very important parameter for the control of the MOVPE growth kinetics.     

Nondestructive Quantitative Evaluation of Porosity Volume Distribution in Aluminum Alloy Die Castings by Fractal Analysis

The nondestructive and three-dimensional quantitative evaluation of porosity in aluminum alloy die castings is proposed to identify whether the predominant cause of pore formation is shrinkage or entrapped gas. The validity of this method of evaluation was shown by comparing two different regions with different ratios of pores formed by shrinkage and gas. It was shown that the proposed evaluation can be used as a quantitative indication of porosity.     

Application and development of synthetic polymer membranes. VI. Pervaporation of aqueous ethanol solution through quaternized poly[3-(N′,N′-dimethyl) aminopropylacrylamide-co-acrylonitrile] membranes

Membranes obtained from polymers, quaternized poly[3-(N′,N′-dimethyl) aminopropylacrylamide-co-acrylonitrile]s, showed selective separation of water from aqueous ethanol solution by pervaporation. The separation factor toward water reached over 15,000. Membrane performance showed a good correlation to membrane polarity. Differential scanning calorimetric melting endotherms of the water-swollen membranes were studied to clarify the state of water in the membranes. The results suggested that there are two states of water in the membrane: bound and free. The higher the fraction of bound water in the membrane, clearly, the more preferentially was water permeated.     

Upper and lower critical solution temperatures in poly (ethylene glycol) solutions

Upper and lower critical solution temperatures have been determined for solutions of poly(ethylene glycol) in t-butyl acetate and water over the molecular weight range of M_η = 2.18 × 10³ to ～1020 × 10³. The phase diagram for solutions of poly(ethylene glycol) (M_η = 719 × 10³) in t-butyl acetate was expressed as the ‘hour glass’ type, while the phase diagram for solution of poly(ethylene glycol) (M_η = 2.18 × 10³ to ～2.29 × 10³) in water was expressed as the ‘closed loop’ type. The value of the pressure dependence of the lower critical solution temperature $\text{(}\text{d}\text{T}\text{d}\text{P}\text{)}{}_{\mathrm{c}}$ in the poly(ethylene glycol) (M_η = 1020 × 10³)/water system over the pressure range of 0 to ～50 atm was negligibly small and positive.     

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel are performed. The sizes of a regenerative heat exchanger and a boiler are expected to be smaller for He than for Ar. The pressure loss of a working gas in a regenerative heat exchanger is reduced for He. The purification subsystem for He is expected to be more compact and economical than that for Ar; but a larger compressor is required for He than for Ar.     

Surgical treatment of Cronkhite-Canada syndrome associated with protein-losing enteropathy: report of a case

PURPOSE: The case of a patient with Cronkhite-Canada syndrome, who developed a protein-losing enteropathy, is reported. METHODS: After localization of the protein-losing region, a right colectomy was performed. RESULTS: Hypoproteinemia and ectodermal changes improved postoperatively. CONCLUSIONS: Surgery is an effective treatment for protein-losing enteropathy in Cronkhite-Canada syndrome. Ectodermal changes improve after correcting malnutrition.