Performance prediction of a hybrid‐excitation synchronous machine with axially arranged excitation poles and permanent‐magnet poles

This paper presents a method of predicting the steady‐state performance of a new hybrid‐excitation synchronous machine (HESM) theoretically. The field pole of this HESM is axially divided into two parts; one is an excitation part and the other a permanent‐magnet (PM) part. A nonlinear equivalent circuit, which can include the saliency of the rotor and the magnetic saturation due to the iron core, is derived. Based on this equivalent circuit, the steady‐state performance of the HESM is calculated, and the results are confirmed through experiments. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 43–49, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20033     

Simulation program for estimating statistical power of Cox's proportional hazards model assuming no specific distribution for the survival time

Small sample properties of the maximum partial likelihood estimates for Cox's proportional hazards model depend on the sample size, the true values of regression coefficients, covariate structure, censoring pattern and possibly baseline hazard functions. Therefore, it would be difficult to construct a formula or table to calculate the exact power of a statistical test for the treatment effect in any specific clinical trial. The simulation program, written in SAS/IML, described in this paper uses Monte-Carlo methods to provide estimates of the exact power for Cox's proportional hazards model. For illustrative purposes, the program was applied to real data obtained from a clinical trial performed in Japan. Since the program does not assume any specific function for the baseline hazard, it is, in principle, applicable to any censored survival data as long as they follow Cox's proportional hazards model.     

Advanced process device technology for 0.3-μm high-performancebipolar LSIs

A new method is developed for forming shallow emitter/bases, collectors, and graft bases suitable for high-performance 0.3-μm bipolar LSIs. Fabricated 0.5-μm U-SICOS (U-groove isolated sidewall base contact structure) transistors are 44 μm², and they have an isolation width of 2.0 μm, a minimum emitter width of 0.2 μm, a maximum cutoff frequency (f_T) of 50 GHz, and a minimum ECL gate delay time of 27 ps. The key points for fabricating high-performance 0.3-μm bipolar LSIs are the control of the graft base depth and the control of the interfacial layer between emitter poly-Si and single-Si. The importance of a tradeoff relation between f_T and base resistance is also discussed     

A 6-ns ECL 100 K I/O and 8-ns 3.3-V TTL I/O 4-Mb BiCMOS SRAM

The authors report a 4 M word×1 b/1 M word×4 b BiCMOS SRAM that can be metal mask programmed as either a 6-ns access time for an ECL 100 K I/O interface to an 8-ns access time for a 3.3-V TTL I/O interface. Die size is 18.87 mm×8.77 mm. Memory cell size is 5.8 μm×3.2 μm. In order to achieve such high-speed address access times the following technologies were developed: (1) a BiCMOS level converter that directly connects the ECL signal level to the CMOS level; (2) a high-speed BiCMOS circuit with low threshold voltage nMOSFETs; (3) a design method for determining the optimum number of decoder gate stages and the optimum size of gate transistors; (4) high-speed bipolar sensing circuits used at 3.3-V supply voltage; and (5) 0.55-μm BiCMOS process technology with a triple-well structure     

A spot-size transformer based on mode interference

A novel mode-size transformer based on interference between guided and leaky modes is proposed and analyzed. Simulation shows significant improvement in spot-size transform efficiency per unit length, in comparison with the conventional tapered waveguide mode size converters based on mode evolution. Owing to its structural simplicity, easy fabrication is another merit of the new spot-size transformer     

Structure of microporous polypropylene sheets containing CaCO3 filler

The microporous polypropylene sheets were prepared by biaxially stretching polypropylene sheets containing CaCO₃ filler (particle size, 0.08–3.0 μm), when the CaCO₃ filler content was 59% by weight and the stretching ratio was 2.8 × 1.8. The microstructure of the sheets were investigated in relation to the CaCO₃ particle size by a N₂ gas permeation method. (1) Effective porosity increases with decreasing mean particle size of filler. (2) The tortuosity factor of the pore is in the range of 25–40 and becomes relatively smaller with decreasing mean particle size of filler. (3) The equivalent pore size becomes relatively smaller with decreasing mean particle size of filler.     

A novel on-chip electrostatic discharge (ESD) protection withcommon discharge line for high-speed CMOS LSIs

A novel on-chip electrostatic discharge (ESD) protection for high-speed CMOS LSI's that operate at higher than 500 MHz has been developed. Introduction of a newly developed common discharge line (CDL) can completely eliminate the protection device influence on the inner circuit operation. This enables minimization of the I/O capacitance by shrinking the dimension of the output transistor, which also serves as a protection device in conventional devices. This new protection (CDL protection) was applied to a high-speed DRAM of which I/O pin capacitance specification is 2 pF. As a result, the ESD tolerance of 4 kV for the charged device model test, 4 kV for the human body model test, and 700 V for the machine model test were obtained. In addition, the DRAM data rate higher than 660 MHz at room temperature was achieved. The results show significant improvement for both ESD and the I/O capacitance, compared with the conventional structure     

Phenotypic diversity and kinetics of proliferating microglia and astrocytes following cortical stab wounds

Brain injury induces reactive gliosis, characterized by increased expression of glial fibrillary acidic protein (GFAP), astrocyte hypertrophy, and hyperplasia of astrocytes and microglia. One hypothesis tested in this study was whether ganglioside GD3+ glial precursor cells would contribute to macroglial proliferation following injury. Adult rats received a cortical stab wound. Proliferating cells were identified by immunostaining for proliferating cell nuclear antigen (PCNA) and by [3H]-thymidine autoradiography, and cell phenotypes by immunocytochemical staining for GD3, GFAP, ED1 (for reactive microglia) and for Bandeiraea Simplicifolia isolectin-B4 binding (all microglia). Animals were labeled with thymidine at 1,2,3, and 4 days postlesion (dpl) and sacrificed at various times thereafter. Proliferating cells of each phenotype were quantified. A dramatic upregulation of GD3 on ramified microglia was seen in the ipsilateral hemisphere by 2 dpl. Proliferating cells consisted of microglia and fewer astrocytes. Microglia proliferated maximally at 2-3 dpl and one third to one half were GD3+. Astrocytes proliferated maximally at 3-4 dpl, and some were also GD3+. Both ramified and ameboid forms of microglia proliferated and by 4 dpl all GD3+ microglia were ED1+ and vice versa. In the contralateral cortex microglia expressed neither GD3 nor ED1. Thus they acquired these antigens when activated. Neither microglia nor astrocytes that were thymidine-labeled at 2, 3, or 4 dpl changed in number in subsequent days. Most thymidine+ astrocytes were large GFAP+ reactive cells that clearly arose from pre-existing astrocytes, not from GD3+ glial precursors. In this model of injury microglia proliferate earlier and to a much greater extent than astrocytes, they can divide when in ramified form, and GD3 is up-regulated in most reactive microglia and in a subset of reactive astrocytes. We also conclude that microglial proliferation precedes proliferation of invading blood-borne macrophages.