Vibration monitoring of high speed spindles using spectral analysis techniques

A significant source of noise and vibration in precision high speed machine tool spindles is bearing induced vibration, which is caused by inherent geometrical characteristics, as well as out-of-balance assembly and interactions between rolling mating members with surface irregularities. The multitude of causes often makes a diagnostic approach quite arduous, particularly due to insufficient information obtained from frequency domain analysis alone. Furthermore, the averaging nature of Fourier analysis and its poor frequency resolution make the task in complex vibration spectra more difficult. The paper presents a new approach in use of auto-correlation analysis with good frequency resolution, combined with windowing capability to isolate significant causes for subsequent remedial actions. The method is applied to a routing spindle with special reference to primary induced bearing frequencies.     

Cation exchange membranes by radiation-induced graft copolymerization of styrene onto PFA copolymer films. I. Preparation and characterization of the graft copolymer

PFA-g-polystyrene graft copolymers were prepared by simultaneous radiation-induced graft copolymerization of styrene onto poly(tetrafluoroethylene-co-perfluorovinyl ether) (PFA) films. The effects of grafting conditions such as monomer concentration, dose, and dose rate were investigated. Three solvents, i.e., methanol, benzene, and dichloromethane, were used as diluents in this grafting system. Of the three solvents employed, dichloromethane was found to greatly enhance the grafting process, and the degree of grafting increased with the increase of monomer concentration until it reached its highest value at a styrene concentration of 60 (vol %). The dependence of the initial rate of grafting on the monomer concentration was found to be of the order of 1.2. The degree of grafting was found to increase with the increase in irradiation dose, while it considerably decreased with the increase in dose rate. The formation of graft copolymers was confirmed by FTIR analysis. The structural investigation by X-ray diffraction (XRD) shows that the degree of crystallinity content of such graft copolymers decreases with the increase in grafting, and consequently, the mechanical properties of the graft copolymers were influenced to some extent. Both tensile strength and elongation percent decreased with the increase in the degree of grafting. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2095–2102, 1999     

旋转对称支承板机座参数化设计与结构优化

对旋转对称支承板机座的支承板进行了参数化建模,并建立了旋转对称支承板机座支承板的优化设计模型.利用ANSYS对机座支承板进行了尺寸优化分析,通过支承板相关尺寸的优化分析得到了影响机座刚度最敏感的部分是支承板宽度,同时通过改变支承板宽度尺寸得到了支承板宽度与机座径向刚度的变化关系.     

Statistical image reconstruction for polyenergetic X-ray computed tomography

This paper describes a statistical image reconstruction method for X-ray computed tomography (CT) that is based on a physical model that accounts for the polyenergetic X-ray source spectrum and the measurement nonlinearities caused by energy-dependent attenuation. We assume that the object consists of a given number of nonoverlapping materials, such as soft tissue and bone. The attenuation coefficient of each voxel is the product of its unknown density and a known energy-dependent mass attenuation coefficient. We formulate a penalized-likelihood function for this polyenergetic model and develop an ordered-subsets iterative algorithm for estimating the unknown densities in each voxel. The algorithm monotonically decreases the cost function at each iteration when one subset is used. Applying this method to simulated X-ray CT measurements of objects containing both bone and soft tissue yields images with significantly reduced beam hardening artifacts.     

An adaptive resource management for mobile terminals on vertical handoff

Mobile communications and wireless networks are developing at a fast pace. The increasing number of mobile subscribers and terminals are the real life evidence of the fast growing development in the area of wireless communication. Wireless communication technology is now pursuing 4G (fourth generation) and seeking a scheme to provide quality of service (QoS) to the various applications continuously even moving to another network. In this paper, we proposed a dynamic resource management architecture which considers vertical handoff situation with minimal disruption of service to the users considering seamless provision of QoS. The proposed scheme efficiently manages resources and provides stable services to the mobile terminal. The simulation results show that resource management enabled mobile terminals utilize system resources, CPU and memory, efficiently improved by 40% and 65%, respectively, rather than mobile terminals without resource tuning.     

Superposition Coding with Unequal Error Protection for the Uplink of Overloaded DS-CDMA System

The overloaded CDMA schemes exploited in direct sequence CDMA (DS-CDMA) systems are mainly to accommodate a greater number of users than the available spreading factor N. In this paper, a superposition coding CDMA (SPC-CDMA) with unequal error protection (UEP) is proposed as one of the overloaded CDMA schemes for the next generation mobile communication systems. It exploits the available power control in most base stations to adapt the transmitted power of active users in the uplink channel. In this scheme, the active users are divided into G groups and each group consists of K users. The K users share the same spreading sequence and are distinguished by different received power levels. At the receiver side, the system first performs despreading for group detection followed by multiuser receiver to estimate the K user signals in each group. It is shown through simulations that better performance are achieved compared to the conventional DS-CDMA and existing overloaded collaborative spreading CDMA (CS-CDMA) schemes, in additive white Gaussian noise (AWGN) and fading channels. Hence, the proposed scheme maximizes the system capacity K-fold compared to conventional DS-CDMA system without requiring extra spreading codes, with average signal to noise ratio (SNR) cost of only 1dB and 2 dB over AWGN and fading channels respectively at BER of 10^?3. On the other hand, for the same N, K and power constraints, SPC-CDMA scheme achieves twofold increase in data rate with 0.7 and 4 dB gains over AWGN and fading channels respectively, compared with overloaded CS-CDMA scheme in the same system capacity. In addition, the proposed scheme can also attain different levels of UEP for different users?? requirements by adjusting their fractions of transmitted powers.     

Do personality problems improve during psychodynamic supportive–expressive psychotherapy? Secondary outcome results from a randomized controlled trial for psychiatric outpatients with personality disorders.

Studies involving patients with personality disorders (PDs) have not focused on improvement of core aspects of the PD. The authors examined changes in quality of object relations, interpersonal problems, psychological mindedness, and personality traits in a sample of 156 patients with Diagnostic and Statistical Manual of Mental Disorders (4th ed.) PD diagnoses being randomized to either manualized or nonmanualized dynamic psychotherapy. Effect sizes adjusted for symptomatic change and reliable change indices were calculated. The authors found that both treatments were equally effective at reducing personality pathology. Only in neuroticism did the nonmanualized group do better during the follow-up period. The largest improvement was found in quality of object relations. For the remaining variables, only small and clinically insignificant magnitudes of change were found. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Optimization of biohydrogen production by Clostridium butyricum EB6 from palm oil mill effluent using response surface methodology

Clostridium butyricum EB6 successfully produced hydrogen gas from palm oil mill effluent (POME). In this study, central composite design and response surface methodology were applied to determine the optimum conditions for hydrogen production (P_c) and maximum hydrogen production rate (R_max) from POME. Experimental results showed that the pH, temperature and chemical oxygen demand (COD) of POME affected both the hydrogen production and production rate, both individually and interactively. The optimum conditions for hydrogen production (P_c) were pH 5.69, 36 °C, and 92 g COD/l; with an estimated P_c value of 306 ml H₂/g carbohydrate. The optimum conditions for maximum hydrogen production rate (R_max) were pH 6.52, 41 °C and 60 g COD/l; with an estimated R_max value of 914 ml H₂/h. An overlay study was performed to obtain an overall model optimization. The optimized conditions for the overall model were pH 6.05, 36 °C and 94 g COD/l. The hydrogen content in the biogas produced ranged from 60% to 75%.     

Effect of thermomechanical treatment on microstructure and hardness behavior of AZ63 magnesium alloy

Due to their high specifc strength and low density, magnesium alloys are widely used in many weight-saving applications. This research is aimed at investigating the microstructure and hardness of commercial AZ63 alloy specimens subjected to two diferent thermomechanical treatments (TMTs). For the first TMT, after solution treated at the temperature of 380 ℃ for 20 h, AZ63 alloy specimens were 5% cold worked by rolling process followed by ageing at the temperatures of 150 ℃ and 250 ℃ for 3, 9 and 25 h. In the second TMT, the specimens were solution treated at the temperature of 380 ℃ for 20 h, underwent 2% cold worked and quenched in water of 0 ℃. Half of the specimens were then 2% cold worked whilst the rest were rolled to 8% cold worked. All the specimens were then aged at the temperatures of 150 ℃ and 250 ℃ for 3, 9 and 25 h. Optical microscope was used to analyze the microstructures of the specimens. Hardness test was too conducted to measure the effect of the treatments on the specimens. Results show that two-step aging enhances the hardness of the specimens due to the distribution of the Beta-phase (Mg₁₇Al₁₂) in the alloy matrix. The results also reveal that, the best hardness from the first TMT was produced by specimen that was pre-aged at 150 ℃ whereas, in the second TMT, aging at 250 ℃　exhibited the best hardness values.     

Spectral analysis methods for vehicle interior vibro-acoustics identification

Noise has various effects on comfort, performance and health of human. Sound are analysed by human brain based on the frequencies and amplitudes. In a dynamic system, transmission of sound and vibrations depend on frequency and direction of the input motion and characteristics of the output. It is imperative that automotive manufacturers invest a lot of effort and money to improve and enhance the vibro-acoustics performance of their products. The enhancement effort may be very difficult and time-consuming if one relies only on ‘trial and error’ method without prior knowledge about the sources itself. Complex noise inside a vehicle cabin originated from various sources and travel through many pathways. First stage of sound quality refinement is to find the source. It is vital for automotive engineers to identify the dominant noise sources such as engine noise, exhaust noise and noise due to vibration transmission inside of vehicle. The purpose of this paper is to find the vibro-acoustical sources of noise in a passenger vehicle compartment. The implementation of spectral analysis method is much faster than the ‘trial and error’ methods in which, parts should be separated to measure the transfer functions. Also by using spectral analysis method, signals can be recorded in real operational conditions which conduce to more consistent results. A multi-channel analyser is utilised to measure and record the vibro-acoustical signals. Computational algorithms are also employed to identify contribution of various sources towards the measured interior signal. These achievements can be utilised to detect, control and optimise interior noise performance of road transport vehicles.