Microcavity distributed-feedback laser using dye-doped polymeric thin films

An organic microcavity laser, in which all the stacked polymer layers are doped with pyrromethene-567 dye, is presented. Singlemode laser oscillation at 568 nm was obtained that was located in the middle of the stopband. The lasing threshold was found to be 260 nJ/pulse, which corresponded to 300 muJ/cm² in the pulse energy density     

3He Impurity Effects on the Growth Kinetics of 4He Crystals

We report the growth kinetics of the⁴He crystals with a small amount of³He impurities around 0.8 K. The growth resistance was measured using the response of the charged interface with respect to an externally applied voltage. In 5 ppm and 10 ppm³He mixtures, it is found that (1) the relaxation process can be expressed as an exponential behavior, (2) the growth resistance becomes larger compared to pure⁴He and does not have a strong³He concentration dependence, and (3) the temperature dependence of the growth resistance is much the same as pure⁴He. We discuss several possible explanations of the present experiment.     

Improved ADPCM voice signal transmission employing click-noisedetection scheme for TDMA-TDD personal communication systems

In personal communication systems, better voice quality and lower terminal price are essential requirements, and adaptive differential pulse-code modulation (ADPCM) codecs are one of the voice codec candidates that have good voice quality and reasonable cost. However, in slow fading environments, burst errors induce click noise in ADPCM voice signal transmission. This paper proposes a novel error-concealment scheme to improve the ADPCM voice signal transmission quality of time division multiple access time division duplex (TDMA-TDD) personal communication systems in slow fading environments. The proposed scheme employs an improved error-detection technique with PCM differential detection and overflow detection coupled with a cyclic redundancy check (CRC) code. To compensate for residual click noise, an expanded CRC error-detection signal is used. Erroneous PCM signals are adaptively suppressed according to the click-noise detection information. Hardware simulation results show that these techniques significantly improve ADPCM voice signal transmission quality by 0.5 points and 1.0 compared to that of the conventional ADPCM muting scheme and no processing, respectively, with the mean opinion scoring (MOS) test in the slow fading environments typical of personal communication systems     

Electrical properties at p-ZnSe/metal interfaces

In order to prepare low resistance ohmic contacts to p-ZnSn by the “deposition and annealing (DA)” technique which has been extensively used for GaAs and Si-based devices, formation of a heavily doped layer by the p-ZnSe/metal reaction is required. For p-ZnSe/Ni contacts, Ni and Se reacted preferentially at the ZnSe/Ni interface upon annealing at temperatures higher than 250°C. However, capacitance-voltage measurements showed that the net acceptor concentration (N_A-N_D) close to the p-ZnSe/Ni interface was reduced upon the Ni/ZnSe reaction, resulting in high contact resistance. For p-ZnSe/Au contacts, neither Au/ZnSe reaction nor reduction of the acceptor concentration were observed after annealing at temperatures lower than 300°C. This indicates that although the metal/p-ZnSe reaction is mandatory to prepare a heavily doped layer, the reaction induced an increase in the compensation donors in the p-ZnSe substrate. In order to increase the acceptor concentration in the vicinity of the p-ZnSe/metal interface through diffusion from the contact materials, Li or O which was reported to play the role of an acceptor in ZnSe was deposited with a contact metal and annealed at elevated temperatures. Ni or Ag was selected as the contact metal, because these metals were expected to enhance Li or O doping by reacting with ZnSe. However, the current density-voltage characteristics of the Li(N)/Ni and Ag(O) contacts exhibited rectifying behavior, and the contact resistances increased with increasing annealing temperature. The present results indicated that, even though the acceptor concentration in the p-ZnSe substrate increased by diffusion of the dopants from the contact elements, an increment of the compensation donors was larger than that of the acceptors. The present experiments indicated that preparation of low resistance ohmic contacts by forming a heavily doped intermediate layer between p-ZnSe and metal is extremely difficult by the DA technique.     

Optimization of a schottky barrier mixer diode in the submillimeter wave region

We have designed a mixer Schottky barrier diode (SBD) for use in the submillimeter wave region with a structure optimized for minimum noise temperature. The dependence of mixer noise temperature upon thickness and doping density of the epitaxial layer and diode diameter of SBDs was simulated within the framework of existing theories. Special care was taken to formulate the SBD current-voltage and capacitance-voltage relations in a way that correctly describes the behavior of real SBDs.     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Current collecting efficiency of micro tubular SOFCs

In this study, current collecting efficiency of the micro tubular solid oxide fuel cell (SOFC) was estimated to determine optimum size of the micro tubular SOFC. Two models for collecting current from single terminal (ST) and double terminal (DT) of anode tube were proposed and used to calculate the current collecting efficiency as functions of anode thickness, tube length and operating temperature. It was shown that design of the cell geometry and current correcting method are significantly important to achieve high performance micro tubular SOFC stacks. The efficiency loss estimated from the DT model was about 2–4-fold lower than those of obtained from the ST model. The DT model was shown to be more effective for higher operating temperature and the tube length.     

Beta-thujaplicin zinc chelate induces apoptosis in mouse high metastatic melanoma B16BL6 cells

The cytotoxic effects of beta-thujaplicin and five kinds of metal chelates were examined on mouse melanoma B16BL6 cells by cell viability and lactate dehydrogenase (LDH) release assay. Beta-thujaplicin-zinc chelate and beta-thujaplicin-copper chelate had higher cytotoxic effects than beta-thujaplicin, and the 50% effective doses (ED50) of these metal chelates were 12.5 and 25 microM, respectively. In addition, the zinc chelate induced DNA ladder formation in B16BL6 cells, as shown by the DNA fragmentation assay, suggesting that cell death induced by the zinc chelate is apoptosis. The zinc chelate also had a cytotoxic effect and induced DNA fragmentation on other tumor cell lines: HeLa, Meth A, and B16F1 cells, but not on normal human diploid fibroblasts FS-4. These results suggest that beta-thujaplicin-zinc chelate induces apoptotic cell death in various tumor cell lines and is a potent antitumor agent for tumor cells including malignant melanomas.