Application of FTIR Spectroscopy for the Determination of Virgin Coconut Oil in Binary Mixtures with Olive Oil and Palm Oil

Rapid Fourier transform infrared (FTIR) spectroscopy combined with attenuated total reflectance (ATR) was applied for quantitative analysis of virgin coconut oil (VCO) in binary mixtures with olive oil (OO) and palm oil (PO). The spectral bands correlated with VCO, OO, PO; blends of VCO and OO; VCO and PO were scanned, interpreted, and identified. Two multivariate calibration methods, partial least square (PLS) and principal component regression (PCR), were used to construct the calibration models that correlate between actual and FTIR-predicted values of VCO contents in the mixtures at the FTIR spectral frequencies of 1,120–1,105 and 965–960 cm⁻¹. The calibration models obtained were cross validated using the “leave one out” method. PLS at these frequencies showed the best calibration model, in terms of the highest coefficient of determination (R ²) and the lowest of root mean standard error of calibration (RMSEC) with R ² = 0.9992 and RMSEC = 0.756, respectively, for VCO in mixture with OO. Meanwhile, the R ² and RMSEC values obtained for VCO in mixture with PO were 0.9996 and 0.494, respectively. In general, FTIR spectroscopy serves as a suitable technique for determination of VCO in mixture with the other oils.     

Estimation of a Unique Pair of Nash Model Parameters: An Optimization Approach

Water resources planning and management requires hydrologic models to estimate runoff from a catchment. For catchments with limited data, the choice of model and identification of its parameters is very important for development of a direct runoff hydrograph. A method is presented to determine a unique pair of hydrologic parameters of the Nash Model, number of linear cascade (n) and storage coefficient (k), using optimization based on Downhill Simplex technique. In this study physical parameters of the catchment are derived from (SPOT) satellite imageries of the basin using ERDAS software. Four different objective functions of varying complexity are tested to find the best solution. Weighted root mean square error (RMSE) and Model Efficiency (Nash-Sutcliffe coefficient) are used to evaluate the model performance. Using the NASH model, a direct surface runoff hydrograph (DSRH) is developed. Kaha catchment is part of Indus river system and is located in the semi-arid region of Pakistan. This catchment is dominated by hill torrent flows and is used in this work to demonstrate the applicability of the proposed method. Ten randomly selected rainfall-runoff events are used for calibration and five events are used for validation. Model results during validation are very promising with model efficiency exceeding 93% and error in peak discharge under 8%. The sensitivity of the Nash model output in response to variation in hydrologic parameters n and k is also investigated. When evaluating the hydrologic response of large catchments, model output is more sensitive to n as compared to k indicating that the runoff diffusion phenomenon is dominant compared to translation flow effects.     

Extraction and determination of methylpyrazines in cocoa beans using coupled steam distillation-microdistillator

The formation of methylpyrazines was determined in fermented cocoa beans (Ivory Coast), in laboratory and industrially roasted samples. The determination of these methylpyrazines was studied by coupled steam distillation-microdistillation as the extraction method and gas chromatography using capillary column and a thermionic detector. The monomethyl-; 2,3-dimethyl-; 2,5-dimethyl-; 2,6-dimethyl-; trimethyl- and the tetramethylpyrazine were detected in non-roasted cocoa beans. Their concentration increased rapidly in laboratory roasted cocoa beans and industrial samples, only the tetramethylpyrazine showed a maximum peak of concentration. The principal compound was the tetramethylpyrazine in fermented and roasted cocoa beans. The determination of the different methylpyrazines in cocoa beans would permit both the evaluation of cocoa mass quality and the control of the cocoa roasting process.     

Thyroid surgery for tumours: the Semon Lecture, presented at the RSM November 1996

1,1,1-Trichloroethane (TRI) is a commonly used industrial solvent with a considerable potential for inhalation abuse. Previous studies in our laboratory and elsewhere have shown that this agent exerts a suppressant effect on operant responding, as well as a number of additional neurobehavioral effects that are similar to those of central nervous system (CNS) depressant drugs. In an effort to provide information relevant to potential mechanisms involved in the behavioral effects and abuse potential of TRI, the present study evaluated the acute effects of this agent on the activity of the hypothalamo-pituitary-adrenal (HPA) axis . Male Sprague-Dawley rats were exposed to 3500 or 5000 ppm TRI by inhalation for 10 or 30 min. Following exposure, plasma levels of adrenocorticotropic hormone (ACTH) and corticosterone and levels of ACTH and corticotropin-releasing factor (CRF) in three brain regions--hypothalamus, hippocampus, and frontal cortex--were determined by selective radioimmunoassays. Levels of TRI in the three brain regions as well as blood were measured by headspace gas chromatography to determine the target tissue concentrations responsible for neuroendocrine changes. Uptake of TRI in blood and all brain regions was very rapid, with stable concentrations apparently achieved within 10 min and maintained for 30 min. During this time course, a significant decrease in plasma corticosterone was produced at 30 min but no significant change in plasma ACTH was observed with 3500 ppm TRI. However, after exposure to 5000 ppm, both plasma ACTH and plasma corticosterone were significantly reduced at 10 and 30 min. ACTH levels in the three brain regions were not significantly changed by TRI, while hypothalamic CRF was significantly increased during exposure to 3500 ppm. However, hypothalamic concentrations of CRF declined following 30 min at 3500 ppm and were not significantly changed by 5000 ppm. This complexity of effects on the regulation of HPA axis activity likely precluded the establishment of consistent relationships between changes in hormonal levels and blood or regional brain concentrations of the inhalant. However, these actions of TRI were strikingly similar to those previously reported for the benzodiazepines.     

Development of a novel nanocomposite consisting of 3-(4-methoxyphenyl)propionic acid and magnesium layered hydroxide for controlled-release formulation

ABSTRACT

Magnesium layered hydroxide (MLH) intercalated with anionic 3-(4-methoxyphenyl)propionic acid (MPP) was synthesised by a direct reaction method using magnesium oxide and MPP as precursors. A further coating of chitosan was applied on the external surface of MLH–MPP nanocomposite to form a new material, named MLH–MPP/chitosan nanocomposite. The XRD pattern showed an intense and sharp peak at basal spacing 18.9 Å, proving that MPP anions were successfully intercalated into the interlayer gallery of MLH in a monolayer arrangement. The XRD pattern of the MLH–MPP/chitosan nanocomposite shows similar peaks with the MLH–MPP nanocomposite. The result was also supported by FTIR spectra and elemental analysis. TGA/DTG spectra showed that the thermal stabilities of the guest anion in the both nanocomposites were markedly enhanced. A controlled-release study of the MPP ion from the MLH–MPP/chitosan nanocomposite showed a slower release compared to MLH–MPP nanocomposite with an initial rapid release and slow release thereafter. Meanwhile, the release behaviours of MPP ions from both nanocomposites were governed by pseudo-second order kinetics. This result highlights the potential of the nanocomposite as an encapsulated material for the controlled-release formulation of MPP anions.     

The Ni3Al-Ni3Cr-Ni3Ru section of the Ni-Cr-Al-Ru system

An investigation is reported of the 75 at% nickel section of the Ni-Cr-Al-Ru system at 1523 and 1273 K. Constitutional data obtained by electron probe microanalysis, X-ray diffraction and microscopical examination are presented as partial isothermal sections. At 1523 K, the major part of the section consists of phase, while the aluminium-rich region contains a and+ region; the extent of the solid solution of chromium and ruthenium in totals ~ 4 at%. The ruthenium-rich corner of the section shows a two-phase region consisting of + ruthenium-rich solid solution. At 1273 K the,+ and + ruthenium regions increase in extent. The/ mismatch values in the equilibrated alloys studied lie in the range ~ –0.08 to –0.39%. Constitutional features of as-cast alloys are also reported.     

A Highly Efficient Algorithm for Phased-Array mmWave Massive MIMO Beamforming

With the rapid development of the mobile internet and the internet of things (IoT), the fifth generation (5G) mobile communication system is seeing explosive growth in data traffic. In addition, low-frequency spectrum resources are becoming increasingly scarce and there is now an urgent need to switch to higher frequency bands. Millimeter wave (mmWave) technology has several outstanding features—it is one of the most well-known 5G technologies and has the capacity to fulfil many of the requirements of future wireless networks. Importantly, it has an abundant resource spectrum, which can significantly increase the communication rate of a mobile communication system. As such, it is now considered a key technology for future mobile communications. MmWave communication technology also has a more open network architecture; it can deliver varied services and be applied in many scenarios. By contrast, traditional, all-digital precoding systems have the drawbacks of high computational complexity and higher power consumption. This paper examines the implementation of a new hybrid precoding system that significantly reduces both calculational complexity and energy consumption. The primary idea is to generate several sub-channels with equal gain by dividing the channel by the geometric mean decomposition (GMD). In this process, the objective function of the spectral efficiency is derived, then the basic tracking principle and least square (LS) techniques are deployed to design the proposed hybrid precoding. Simulation results show that the proposed algorithm significantly improves system performance and reduces computational complexity by more than 45% compared to traditional algorithms.     

Characterisation of sol–gel method synthesised MgZnFe2 O4 nanoparticles and its cytotoxic effects on breast cancer cell line,MDA MB‐231 in vitro

In this study, nanocrystalline magnesium zinc ferrite nanoparticles were successfully prepared by a simple sol–gel method using copper nitrate and ferric nitrate as raw materials. The calcined samples were characterised by differential thermal analysis/thermogravimetric analysis, Fourier transform infrared spectroscopy and X‐ray diffraction. Transmission electron microscopy revealed that the average particle size of the calcined sample was in a range of 17–41 nm with an average of 29 nm and has spherical size. A cytotoxicity test was performed on human breast cancer cells (MDA MB‐231) and (MCF‐7) at various concentrations starting from (0 µg/ml) to (800 µg/ml). The sample possessed a mild toxic effect toward MDA MB‐231 and MCF‐7 after being examined with MTT (3‐[4, 5‐dimethylthiazol‐2‐yl]‐2, 5 diphenyltetrazolium bromide) assay for up to 72 h of incubation. Higher reduction of cells viability was observed as the concentration of sample was increased in MDA MB‐231 cell line than in MCF‐7. Therefore, further cytotoxicity tests were performed on MDA MB‐231 cell line.Inspec keywords: sol‐gel processing, nanoparticles, nanofabrication, magnesium compounds, zinc compounds, toxicology, biological organs, cancer, cellular biophysics, nanomedicine, calcination, differential thermal analysis, Fourier transform infrared spectra, X‐ray diffraction, transmission electron microscopy, particle size, organic compoundsOther keywords: sol‐gel method, cytotoxic effects, breast cancer cell line, MDA MB‐231 in vitro, nanocrystalline magnesium zinc ferrite nanoparticles, copper nitrate, ferric nitrate, raw materials, calcined samples, differential thermal analysis, thermogravimetric analysis, Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, average particle size, cytotoxicity testing, human breast cancer cells, mild toxic effect, 3‐[4,5‐dimethylthiazol‐2‐yl]‐2,5 diphenyltetrazolium bromide) assay, cell viability, MCF‐7, MDA MB‐231 cell line, size 17 nm to 41 nm     

Health risk assessment of inorganic arsenic intake of Cambodia residents through groundwater drinking pathway

In order to compare the magnitudes and health impacts of arsenic and other toxic trace elements in well water, groundwater and hair samples were collected from three areas with different arsenic exposure scenarios in the Mekong River basin of Cambodia. Ampil commune in Kampong Cham province was selected as an uncontaminated area, Khsarch Andaet commune in Kratie province was selected as a moderately contaminated area, and Kampong Kong commune in Kandal Province was selected as an extremely contaminated area. Results of ICP-MS analyses of the groundwater samples revealed that As, Mn, Fe and Ba concentrations were significantly different among the three study areas (Kruskal-Wallis test, p < 0.0001). Out of 46 observed wells in the Kandal province study area, 100% detected As > 50 μg L⁻¹ and Fe > 300 μg L⁻¹; 52.17% had Mn > 400 μg L⁻¹ and 73.91% found Ba > 700 μg L⁻¹. In the Kratie province study area (n = 12), 25% of wells showed elevated arsenic levels above 10 μg L⁻¹ and 25% had Mn > 400 μg L⁻¹, whereas samples from Kampong Cham province study area (n = 18) were relatively clean, with As < 10 μg L⁻¹. A health risk assessment model derived from the USEPA was applied to calculate individual risks resulting from drinking groundwater. Computational results indicated that residents from Kandal Province study area (n = 297) confronted significantly higher non-carcinogenic and carcinogenic risks than those in Kratie (n = 89) and Kampong Cham (n = 184) province study areas (Kruskal-Wallis test, p < 0.0001). 98.65% of respondents from the Kandal province study area were at risk for the potential non-cancer effect and an average cancer risk index was found to be 5 in 1000 exposure. The calculations also indicated that, in the Kratie province study area, 13.48% of respondents were affected by non-cancer health risks and 33.71% were threatened by cancer, whereas none of respondents in the Kampong Cham province study area appeared to have non-carcinogenic effect. Positively significant correlations of the arsenic content in scalp hair (As_h) with both arsenic levels in groundwater (As_w) (r_s (304) = 0.757, p < 0.0001) and individual average daily doses (ADD) of arsenic (r_s (304) = 0.763, p < 0.0001) undoubtedly indicated that arsenic accumulation in the bodies of Cambodia residents in the Mekong River basin was mainly through a groundwater drinking pathway. To the best of our knowledge, this is the first comprehensive report comparing individual health risk assessments of arsenic exposure through a groundwater drinking pathway to enriched arsenic levels from groundwater in the Mekong River basin, Cambodia. This study indicates that elevated arsenic concentrations in groundwater may lead to thousands of cases of arsenicosis in the near future if mitigating actions are not taken.     

Analysis of Lard’s Aroma by an Electronic Nose for Rapid <Emphasis Type=Italic>Halal</Emphasis> Authentication

An electronic nose was successfully used to detect and discriminate lard from other types of animal body fats and samples containing lard. The results are presented in the form of VaporPrint™, the image of the polar plot of the odor amplitudes from the surface acoustic wave (SAW) detector frequency. In the VaporPrint™, the radial angles representing the sensor provides individual fingerprints of the aroma of different animal body fats. Principal component analysis (PCA) was used to interpret the data and it provided a good grouping of samples, with 61% of the variation accounted for by PC 1 and 29% accounted for by PC 2. All of the lard-containing samples formed a separate group from the samples that were free from lard. This method can be developed into a rapid method for detecting the presence of lard in food samples for Halal authentication.