Critical temperature for production of MAG by esterification of different FA with glycerol using <Emphasis Type="Italic">Penicillium camembertii</Emphasis> lipase

Production of MAG by a lipase-catalyzed reaction is known to be effective at low temperature. This phenomenon can be explained by assuming that synthesized MAG are excluded from the reaction system because MAG, which have low m.p., are solidified at low temperatures. Consequently, MAG are efficiently accumulated and do not serve as the precursor of DAG. If this hypothesis is correct, the critical temperature for MAG production, defined as the highest temperature at which DAG synthesis is repressed, should depend on the m.p. of the MAG. Esterification of FFA with glycerol using Candida rugosa, Rhizopus oryzae, and Penicillium camembertii lipases produced MAG efficiently at low temperatures. However, Candida lipase showed very low esterification activity at high temperatures (>20°C), and Rhizopus lipase produced not only MAG but also DAG even at low temperatures. Meanwhile, P. camembertii lipase catalyzed synthesis of MAG only from FFA and glycerol at low temperatures, although the enzyme catalyzed synthesis of DAG from MAG in addition to synthesis of MAG at high temperatures. We thus studied the effect of temperature on esterification of C₁₀−C₁₈ FFA with glycerol using Penicillium lipase as a catalyst and determined the critical temperatures for production of MAG. The critical temperature for production of each MAG showed a linear correlation with m.p. of the MAG, which supported the hypothesis. In addition, because the m.p. of MAG are estimated from that of the constituent FA, the optimal temperature for production of MAG can be predicted from the m.p. of the FFA used as a substrate.     

Fractionation and enrichment of CLA isomers by selective esterification with Candida rugosa lipase

A commercial product of CLA contains almost equal amounts of cis-9,trans-11 (c9,t11)-CLA and trans-10,cis-12 (t10,c12)-CLA. We attempted to enrich the two isomers by a two-step selective esterification using Candida rugosa lipase that acted on c9,t11-CLA more strongly than on t10,c12-CLA. An FFA mixture containing CLA isomers was esterified with an equimolar amount of lauryl alcohol in a mixture of 20% water and the lipase. When the esterification of total FA reached 50%, two isomers were fractionated in a good yield: t10,c12-CLA was enriched in FFA, and c9,t11-CLA was recovered in lauryl esters. The FFA were esterified again to enrich t10,c12-CLA. At 27.3% esterification of total FA, the t10,c12-CLA content in FFA increased to 64.8 wt% with 89.3% recovery: The ratio of the content of t10,c12-CLA to that of two isomers was 95.9%. Lauryl esters obtained by the single esterification were employed for enrichment of c9,t11-CLA. After the esters were hydrolyzed, the resulting FFA were esterified again with lauryl alcohol. At 62.0% esterification of total FA, the c9,t11-CLA content in lauryl esters increased to 73.3 wt% with 79.4% recovery: The ratio of the content of c9,t11-CLA to that of two isomers was 95.6%. In a 600-g-scale purification, molecular distillation was effective in separating the reaction mixture into lauryl alcohol, FFA, and lauryl ester fractions.     

Crosslinked acrylic pressure sensitive adhesives. 3. Effect of adherend on film formation

The reaction of isocyanate in pressure sensitive adhesive (PSA) films adhered on to various adherends having different surface tensions was monitored by depth profiling using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy.In the latter stages of crosslinking reaction, unreacted isocyanate and its derivatives exist more in the bulk of the PSA than in the interfaces between PSA and adherends which are Teflon sheet and PE film having relatively lower surface tensions. In the case of using stainless steel having relatively higher surface tension as adherend, opposite segregation was observed compared to Teflon and PE.From X-ray photoelectron spectroscopy (XPS), it was revealed that N atoms exist more in surface than in bulk when stainless steel is used as adherend. We conclude that polyisocyanates migrate in the PSA film in order to minimize the magnitude of interfacial free energy between the PSA and the adherend, which leads to the change of surface tension of PSA film.     

激光退火对Inconel 718微观组织和硬度的影响

研究激光退火对Inconel718时效合金的显微组织和硬度的影响.一台2.5kW的CO2激光机被用来照射试样的表面.在激光能作用下,试样表面层被加热后空冷.通过控制激光工艺参数,在表面不发生熔化的前提下,能够使一定厚度表面层内的硬度降低到标准退火合金的水平,而不影响试样内部母材的硬度.显微组织观察显示表面层的基体强化相(γ″和γ‘)在激光照射过程中被固溶,而其它二次相没有变化.γ″和γ‘的固溶被确定是表面层硬度下降的原因.在其它试验条件不变时,确立了退火层生成时由激光散焦距离和扫描速度描述的工艺参数范围.     

Gain‐Scheduled Control via Switching of LTI Controllers and State Reset

This paper proposes a synthesis method of gain‐scheduled control systems that switch linear time‐invariant controllers according to hysteresis of the scheduling parameter. Stability and L₂‐gain analysis and synthesis methods for switched systems are applied to the switched gain‐scheduled control synthesis using reset of the controller state, where also the reset law is computed via linear matrix inequalities (LMIs). In addition to optimization of an upper bound of L₂‐gain, we reduce jumps of control input via an auxiliary optimization. Numerical examples are presented to illustrate the switched gain‐scheduled controller.     

Frequency Stability Improvement of a Two-Mode Stabilized 633-nm He-Ne Laser

The red side (lower-frequency) mode of a two-mode stabilized 633-nm He-Ne laser has been locked to the hyperfine structure of the P() line of (127)I(2) by means of frequency modulation spectroscopy enhanced by an external optical cavity. Both the red side and blue side (higher-frequency) modes of the laser exhibit a frequency stability of 2.3 x 10(-11) tau(-1/2). In addition, the frequency fluctuations of the blue side mode are detected by a Fabry-Perot cavity and compensated through an acousto-optic frequency shifter. The short-term stability of better than 3 x 10(-11) is attained for integration times of between 2 x 10(-3) and 2 x 10(-1) s.     

Stochastic system transformation using generalized orthonormal basis functions with applications to continuous-time system identification

This paper studies the system transformation using generalized orthonormal basis functions that include the Laguerre basis as a special case. The transformation of the deterministic systems is studied in the literature, which is called the Hambo transform. The aim of the paper is to develop a transformation theory for stochastic systems. The paper establishes the equivalence of continuous and transformed-discrete-time stochastic systems in terms of solutions. The method is applied to the continuous-time system identification problem. It is shown that using the transformed signals the PO-MOESP subspace identification algorithm yields consistent estimates for system matrices. An example is included to illustrate the efficacy of the proposed identification method, and to make a comparison with the method using the Laguerre filter.     

Operational Regimes and Physics Present in Optoelectronic Tweezers

Optoelectronic tweezers (OET) are a powerful light-based technique for the manipulation of micro- and nanoscopic particles. In addition to an optically patterned dielectrophoresis (DEP) force, other light-induced electrokinetic and thermal effects occur in the OET device. In this paper, we present a comprehensive theoretical and experimental investigation of various fluidic, optical, and electrical effects present during OET operation. These effects include DEP, light-induced ac electroosmosis, electrothermal flow, and buoyancy-driven flow. We present finite-element modeling of these effects to establish the dominant mode for a given set of device parameters and bias conditions. These results are confirmed experimentally and present a comprehensive outline of the operational regimes of the OET device.     

Minimizing False Positives of a Decision Tree Classifier for Intrusion Detection on the Internet

Machine learning or data mining technologies are often used in network intrusion detection systems. An intrusion detection system based on machine learning utilizes a classifier to infer the current state from the observed traffic attributes. The problem with learning-based intrusion detection is that it leads to false positives and so incurs unnecessary additional operation costs. This paper investigates a method to decrease the false positives generated by an intrusion detection system that employs a decision tree as its classifier. The paper first points out that the information-gain criterion used in previous studies to select the attributes in the tree-constructing algorithm is not effective in achieving low false positive rates. Instead of the information-gain criterion, this paper proposes a new function that evaluates the goodness of an attribute by considering the significance of error types. The proposed function can successfully choose an attribute that suppresses false positives from the given attribute set and the effectiveness of using it is confirmed experimentally. This paper also examines the more trivial leaf rewriting approach to benchmark the proposed method. The comparison shows that the proposed attribute evaluation function yields better solutions than the leaf rewriting approach.