In Situ Observation of Phase Separation of a Barium Borate Melt in a Stable Immiscibility Region under Microgravity

The precipitation of droplets was directly observed on a BaO–B₂O₃ melt in a drop shaft experiment. This is the first time that precipitation of droplets has been observed in a 4.5 s drop test. The melt film of 4BaOz96B₂O₃ (mol%) held on a platinum wire loop was heated above the critical tem-perature to produce uniformity and was cooled down to the phase separation temperature range. Phase separation of the melt was observed directly with a video camera. The IR image of the melt was simultaneously detected with a CCD array and was converted into a two-dimensional thermograph.     

Formation and Crystallization of Yttrium Aluminosilicate Glasses Containing Calcium Oxide

Formation of yttrium aluminosilicate glasses containing calcium oxide from batches melted at 1550°C was investigated. Densities and thermal expansion coeflcients were measured for some glasses. In a specific compositional region, crystals with a needlelike habit were observed in the glass matrix. A crystal in the form of a tubular hexagonal prism was identified as Ca₄Y₆0(Si0₄)₆.     

Thermal shock resistance of flat plastic integrated circuit packages

Flat packages (FPs) were formed from epoxy molding compounds with various physical properties using a transfer molding machine. The compounds were prepared by changing kinds and amounts of additives and addition methods. The thermal shock test was carried out by the following procedures. The plastic package was soaked alternately in liquid nitrogen (?196°) and in liquid solder (200°) in the cycle of 140s. The median life to crack initiation was defined to be the cycles when half of the specimens exhibited crack initiation. According to linear fracture mechanics, the following expression was obtained relating the median life N, thermal stress σ_t, and strength σ_b; N = C/σ·(σ_b/σ_t)^m. We found the linear relation between logarithm of Nσ and logarithm of σ_b/σ_t for various packages, and estimated the values of C and m as 5 × 10⁴ MPa² and 5.5, respectively. The value of m was the same as that obtained for a dual-in-line package.     

Dynamic Mechanical Properties and Adhesive Strengths of Emulsion Polymer by Power Feed Technique, I

Dynamic mechanical properties and adhesive strengths of power feed copolymer and random copolymer synthesized using styrene or methyl methacrylate and n-butyl acrylate were investigated. Although the two systems were synthesized from the same raw materials, power feed copolymer had a very broad transition compared with random copolymer. This fact was explained by the fact that the system synthesized through power feed method was an alloy of copolymers which are a continuous series from monomer A rich copolymers to monomer B rich copolymers. The dynamic mechanical behavior of film cast from solution was almost the same as that of emulsion film, which indicated more extensive application of power feed copolymer. In the P(nBA/St) system, power feed copolymer maintained its adhesive strengths over a wide temperature range compared with random copolymer. The absolute value, however, was not so high. This was due to the low cohesive strengths of the films.     

Dynamic Mechanical Properties and Adhesive Joint Strengths of Emulsion Polymers Produced by Power Feed Technique. III. Adhesive Joint Strengths of Grafted Power Feed Copolymer

Power feed copolymers were synthesized using styrene and n-butyl acrylate through non-uniform feeding emulsion polymerization. Poly(vinyl alcohol) (PVA) was used as a protective colloid, onto which vinyl monomers were grafted. Power feed copolymer had a very broad glass transition temperature compared with random copolymer, even if grafting and/or crosslinking were introduced to the system. This tendency was almost the same as the non-grafted power feed copolymer where only low molecular weight surfactant was used.

Adhesive joint strengths of power feed copolymers were evaluated compared with random copolymers. In the case of usual linear power feed copolymer, the adhesive joint strengths were not higher than those of random copolymer, which was considered to be due to the lower film strengths of the power feed copolymer. Power feed copolymer having grafting showed slightly higher adhesive joint strengths over a wide range of temperatures than random copolymer. When crosslinking was introduced to the system, power feed copolymer showed much higher adhesive joint strengths over a wide temperature range.     

New type of tin support for hydroprocessing catalyst

TiN supported molybdenum sulfide catalysts showed much higher activity for cleavage of C-C bonds than oxide supported molybdenum sulfide catalysts, indicating the possibility of a new generation of supports for hydroprocessing catalysts.     

Critical temperature for production of MAG by esterification of different FA with glycerol using <Emphasis Type="Italic">Penicillium camembertii</Emphasis> lipase

Production of MAG by a lipase-catalyzed reaction is known to be effective at low temperature. This phenomenon can be explained by assuming that synthesized MAG are excluded from the reaction system because MAG, which have low m.p., are solidified at low temperatures. Consequently, MAG are efficiently accumulated and do not serve as the precursor of DAG. If this hypothesis is correct, the critical temperature for MAG production, defined as the highest temperature at which DAG synthesis is repressed, should depend on the m.p. of the MAG. Esterification of FFA with glycerol using Candida rugosa, Rhizopus oryzae, and Penicillium camembertii lipases produced MAG efficiently at low temperatures. However, Candida lipase showed very low esterification activity at high temperatures (>20°C), and Rhizopus lipase produced not only MAG but also DAG even at low temperatures. Meanwhile, P. camembertii lipase catalyzed synthesis of MAG only from FFA and glycerol at low temperatures, although the enzyme catalyzed synthesis of DAG from MAG in addition to synthesis of MAG at high temperatures. We thus studied the effect of temperature on esterification of C₁₀−C₁₈ FFA with glycerol using Penicillium lipase as a catalyst and determined the critical temperatures for production of MAG. The critical temperature for production of each MAG showed a linear correlation with m.p. of the MAG, which supported the hypothesis. In addition, because the m.p. of MAG are estimated from that of the constituent FA, the optimal temperature for production of MAG can be predicted from the m.p. of the FFA used as a substrate.     

Fractionation and enrichment of CLA isomers by selective esterification with Candida rugosa lipase

A commercial product of CLA contains almost equal amounts of cis-9,trans-11 (c9,t11)-CLA and trans-10,cis-12 (t10,c12)-CLA. We attempted to enrich the two isomers by a two-step selective esterification using Candida rugosa lipase that acted on c9,t11-CLA more strongly than on t10,c12-CLA. An FFA mixture containing CLA isomers was esterified with an equimolar amount of lauryl alcohol in a mixture of 20% water and the lipase. When the esterification of total FA reached 50%, two isomers were fractionated in a good yield: t10,c12-CLA was enriched in FFA, and c9,t11-CLA was recovered in lauryl esters. The FFA were esterified again to enrich t10,c12-CLA. At 27.3% esterification of total FA, the t10,c12-CLA content in FFA increased to 64.8 wt% with 89.3% recovery: The ratio of the content of t10,c12-CLA to that of two isomers was 95.9%. Lauryl esters obtained by the single esterification were employed for enrichment of c9,t11-CLA. After the esters were hydrolyzed, the resulting FFA were esterified again with lauryl alcohol. At 62.0% esterification of total FA, the c9,t11-CLA content in lauryl esters increased to 73.3 wt% with 79.4% recovery: The ratio of the content of c9,t11-CLA to that of two isomers was 95.6%. In a 600-g-scale purification, molecular distillation was effective in separating the reaction mixture into lauryl alcohol, FFA, and lauryl ester fractions.     

Continuous-velocity lattice gas cellular automata for miscible binary fluid and its application to simulation of interface instability

Continuous-velocity lattice gas cellular automata (CVLGA) is extended to miscible binary fluid systems. A new parameter is introduced in order to control the diffusivity of the fluids. The correlation between the diffusivity and the new parameter proves that there exists the maximum value of the diffusivity. Quantitative verifications of the model are carried out with numerical simulations of the diffusion phenomena across a falling fluid film. The model is then applied to the simulations of Rayleigh-Taylor instability during the gravitational mixing phenomena. The qualitative tendency of the growth of the interface instability is the same as that obtained in conventional numerical methods.     

Crosslinked acrylic pressure sensitive adhesives. 3. Effect of adherend on film formation

The reaction of isocyanate in pressure sensitive adhesive (PSA) films adhered on to various adherends having different surface tensions was monitored by depth profiling using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy.In the latter stages of crosslinking reaction, unreacted isocyanate and its derivatives exist more in the bulk of the PSA than in the interfaces between PSA and adherends which are Teflon sheet and PE film having relatively lower surface tensions. In the case of using stainless steel having relatively higher surface tension as adherend, opposite segregation was observed compared to Teflon and PE.From X-ray photoelectron spectroscopy (XPS), it was revealed that N atoms exist more in surface than in bulk when stainless steel is used as adherend. We conclude that polyisocyanates migrate in the PSA film in order to minimize the magnitude of interfacial free energy between the PSA and the adherend, which leads to the change of surface tension of PSA film.