Some Insights into MIMO Mutual Information: The High SNR Case

We consider mutual information of multiple-input multiple-output (MIMO) wireless channels with complex isotropic Gaussian input in the case where the receiver has perfect channel, knowledge. For arbitrary fading statistics, a mutual information lower bound is decomposed in a sum of three terms involving: a) average SNR; b) channel fading; and c) a term characterizing the "effective rank", or eigenvalue dispersion, of the channel matrix. The decomposition suggests that spatial multiplexing efficiency of a MIMO channel can be characterized by the so-called ellipticity statistic. Distribution functions, means and variances of the random terms in the decomposition for the case of Rayleigh fading are also derived     

Development of crumb rubber reinforced bituminous binder under laboratory conditions

Bituminous binders are widely used in the construction of flexible pavements. However, in some applications, the performance of conventional binders is not considered to be satisfactory. Reinforcing these binders with selected polymers prevents premature failure of a pavement by improving the properties of the binder. Another source of reinforcement comes from crumb (ground) rubber produced from waste tyres. After they have been worn-out during their limited service life, millions of used tyres are discarded every year and are hauled to a dump. The fatigue resistance at temperatures below normal service temperatures (25°C), one of the key engineering properties of crumb rubber reinforced binders, has been found to be lower than that of neat binders. This paper is concerned with the development of a rubber reinforced binder. It was shown that the binder has the potential to be used as an all-weather wearing course in flexible roads, whilst at the same time recycling a considerable amount of waste rubber.     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Anthocyanin composition of the red wine Babić affected by maceration treatment

Identification of anthocyanins in the wine made of the Croatian autochthonous grape variety of Babić (Vitis vinifera L.) was carried out and their profile was determined by means of high-performance liquid chromatography with diode array and mass spectrometric detection. Dependence of anthocyanins content and profile on maceration treatment conditions was investigated. Statistically significant differences of anthocyanins concentration in wines Babić produced by various maceration treatments were confirmed by the use of multivariate analysis of variances. The investigation results indicated that the maceration temperature exerts higher influence on anthocyanins concentration than the duration of maceration. In addition, on the basis of anthocyanin composition and using different multivariate statistical analyses, differentiation of wines Babić according to maceration treatments was procured.     

Extractive Properties of Synergistic Mixtures of Dipicolinic Acid Diamides and Chlorinated Cobalt Dicarbollide

Extraction of Cs, Sr, Eu, U, Np, and Am with mixtures of dipicolinic acid diamides with chlorinated cobalt dicarbollide was studied. A synergistic effect was revealed.     

An Acoustic Converter Used to Measure Ionizing Radiation Energy Loss

A monitor is proposed based on ultrasonic production when ionizing radiation passes through a medium. The recording element is a 0.2 mm aluminum plate mounted in a ceramic acoustic converter AC in the form of a wedge of thickness 2 mm. The low plate thickness minimizes the beam parameter distortion, while special technology used in the AC provides high sensitivity. The device has been calibrated in the proton beam from the ITEP accelerator at 200 MeV with 2·10⁹–6·10¹⁰ particles in a pulse and a pulse length of 70 nsec.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Colloidal processing of polymer ceramic nanocomposite integral capacitors

Polymer ceramic composites form a suitable material system for low temperature fabrication of embedded capacitors appropriate for the MCM-L technology. Improved electrical properties such as permittivity can be achieved by efficient filling of polymers with high dielectric constant ceramic powders such as lead magnesium niobate-lead titanate (PMN-PT) and barium titanate (BT). Photodefinable epoxies as the matrix polymer allow fine feature definition of the capacitor elements by conventional lithography techniques. The optimum weight percent of dispersant is tuned by monitoring the viscosity of the suspension. The dispersion mechanism (steric and electrostatic contribution) in a slightly polar solvent such as propylene glycol methyl ether acetate (PGMEA) is investigated from electrophoretic measurements. A high positive zeta potential is observed in the suspension, which suggests a strong contribution of electrostatic stabilization. By optimizing the particle packing using a bimodal distribution and modified processing methodology, a dielectric constant greater than 135 was achieved in PMN-PT/epoxy system. Suspensions are made with the lowest PGMEA content to ensure the efficiency of the dispersion and efficient particle packing in the dried film. Improved colloidal processing of nanoparticle-filled epoxy is a promising method to obtain ultra-thin capacitor films (<2/spl mu/m) with high capacitance density and improved yield. Capacitance of 35 nF/cm/sup 2/ was achieved with the thinnest films (2.5-3.0 /spl mu/m).     

Enhanced Photoelectrochemistry in CdS/Au Nanoparticle Bilayers

Three different configurations of Au‐nanoparticle/CdS‐nanoparticle arrays are organized on Au/quartz electrodes for enhanced photocurrent generation. In one configuration, Au‐nanoparticles are covalently linked to the electrode and the CdS‐nanoparticles are covalently linked to the bare Au‐nanoparticle assembly. The resulting photocurrent, φ = 7.5 %, is ca. 9‐fold higher than the photocurrent originating from a CdS‐nanoparticle layer that lacks the Au‐nanoparticles, φ = 0.8 %. The enhanced photocurrent in the Au/CdS nanoparticle array is attributed to effective charge separation of the electron–hole pair by the injection of conduction‐band electrons from the CdS‐ to the Au‐nanoparticles. Two other configurations involving electrostatically stabilized bipyridinium‐crosslinked Au/CdS or CdS/Au nanoparticle arrays were assembled on the Au/quartz crystal. The photocurrent quantum yields in the two systems are φ = 10 % and φ = 5 %, respectively. The photocurrents in control systems that include electrostatically bridged Au/CdS or CdS/Au nanoparticles by oligocationic units that lack electron‐acceptor units are substantially lower than the values observed in the analogous bipyridinium‐bridged systems. The enhanced photocurrents in the bipyridinium‐crosslinked systems is attributed to the stepwise electron transfer of conduction‐band electrons to the Au‐nanoparticles by the bipyridinium relay bridge, a process that stabilizes the electron–hole pair against recombination and leads to effective charge separation.