Aqueous-Develop,Photosensitive Polynorbornene Dielectric: Optimization of Mechanical and Electrical Properties

The impact of thermal cure conditions on the mechanical and electrical properties of an epoxy cross-linked network incorporating a polynorbornene (PNB) dielectric polymer was studied. The cross-linking of the dielectric composition was achieved by an acid-catalyzed cationic cure reaction initiated by either thermal or photolytic activation of a photoacid generator. It is proposed that the observed mechanical and electrical properties of the fully cured polymer composition are the result of the development of a three-dimensional cross-linked network tying together the PNB polymer and multifunctional epoxy additives. The epoxy ring-opening reaction was measured using Fourier-transform infrared spectroscopy. The reduced modulus, internal film stress, dielectric constant, and swelling behavior of cross-linked films were studied as a function of curing temperature. Trends in the observed properties are explained by formation of a three-dimensional cross-linked network and degradation of the cross-links between the multifunctional epoxy additives at high temperature. It was also found that exposure of the film to aqueous base plays a role in the cure process and has a positive effect on the final properties. The optimum values of modulus, dielectric constant, residual stress, and moisture content were found for films cured at 160°C for 1 h. This relatively low cure temperature is potentially advantageous in device assembly and processing.     

Calibrating whole building energy models: An evidence-based methodology

This paper reviews existing case studies and methods for calibrating whole building energy models to measured data. This research describes a systematic, evidence-based methodology for the calibration of these models. Under this methodology, parameter values in the final calibrated model reference the source of information used to make changes to the initial model. Thus, the final model is based solely on evidence. Version control software stores a complete record of the calibration process, and the evidence on which the final model is based. Future users can review the changes made throughout the calibration process along with the supporting evidence. In addition to the evidence-based methodology, this paper also describes a new zoning process that represents the real building more closely than the typical core and four perimeter zone approach. Though the methodology is intended to apply to detailed calibration studies with high resolution measured data, the primary aspects of the methodology (evidence-based approach, version control, and zone-typing) are independent of the available measured data.     

High yield polypyrrole: A novel approach to synthesis and characterization

An improved synthetic route to polypyrrole salt was accomplished using methanesulfonic acid as a novel dopant along with potassium persulfate as the oxidant employing inverted emulsion polymerization technique. Polypyrrole salt was obtained in high-weight percent yield (83.77%) with respect to the amount of monomer used and the reaction time was drastically reduced (1 h 10 min.) as compared to the previously reported synthesis methods. Characterization of the salt yielded satisfactory results. Inverted emulsion polymerization technique has several unique and distinct advantages over conventional techniques which facilitate the synthesis of fused five membered heterocyclic rings which are otherwise difficult to synthesize, and hence sparsely reported in the literature.     

Subsampling weakly dependent time series and application to extremes

This paper provides extensions of the work on subsampling by Bertail et al. in J. Econ. 120:295–326 (2004) for strongly mixing case to weakly dependent case by application of the results of Doukhan and Louhichi in Stoch. Proc. Appl. 84:313–342 (1999). We investigate properties of smooth and rough subsampling estimators for sampling distributions of converging and extreme statistics when the underlying time series is η- or λ-weakly dependent.     

Parabolic Flights @ Home

We developed an unmanned air vehicle (UAV) suitable for small parabolic-flight experiments. The flight speed of 100 m s^− 1 is sufficient for zero-gravity parabolas of 16 s duration. The flight path’s length of slightly more than 1 km and 400 m difference in altitude is suitable for ground controlled or supervised flights. Since this fits within the limits set for model aircraft, no additional clearance is required for operation. Our UAV provides a cost-effective platform readily available for low-g experiments, which can be performed locally without major preparation. A payload with a size of up to 0.9 ×0.3 ×0.3 m³ and a mass of ∼5 kg can be exposed to 0 g ₀–5 g ₀, with g ₀ being the gravitational acceleration of the Earth. Flight-duration depends on the desired acceleration level, e.g. 17 s at 0.17 g ₀ (lunar surface level) or 21 s at 0.38 g ₀ (Martian surface level). The aircraft has a mass of 25 kg (including payload) and a wingspan of 2 m. It is powered by a jet engine with an exhaust speed of 450 m s^− 1 providing a thrust of 180 N. The parabolic-flight curves are automated by exploiting the advantages of sophisticated micro-electronics to minimize acceleration errors.