济钢中厚板厂的技术改造与发展

结合济钢中厚板厂二期和三期工程、开发管线钢项目和大板坯连铸高效改造及炉外精炼改造，介绍了该厂的技术改造项目，对今后的发展进行了阐述．     

Effect of deformation route on microstructural development in aluminum processed by equal channel angular extrusion

Aluminum has been deformed by equal channel angular extrusion (ECAE) to obtain submicron-grained structures under different deformation routes. The deformation routes were varied by rotating billets through 0, 90, and 180 deg between each extrusion pass, and were designated as route A, B_C, and C, respectively. Based on quantitative microstructural analysis, the effectiveness of the deformation route is shown to depend upon the different definition used. The order of effectiveness is (a) A > B_C > C for both 90 and 120 deg dies, in terms of the generation of high-angle grain boundaries (HAGBs); (b) B_C > C > A for both 90 and 120 deg dies, in terms of the formation of equiaxed shape of grains; and (c) B_C > A > C for 90 deg die and B_C ∼ A > C for 120 die, in terms of reducing grain size. It is suggested that the generation of HAGBs can be related to the accumulation of nonredundant strain, while the shape and orientation of grains may be linked to the shearing patterns of the deformation route.     

Perturbation analysis and control of two-class stochastic fluid models for communication networks

This paper uses stochastic fluid models (SFMs) for the control and optimization (rather than performance analysis) of communication network nodes processing two classes of traffic: one is uncontrolled and the other is subject to threshold-based buffer control. We derive gradient estimators for packet loss and workload related performance metrics with respect to threshold parameters. These estimators are shown to be unbiased and directly observable from a sample path without any knowledge of underlying stochastic characteristics of the traffic processes. This renders them computable in online environments and easily implementable for network management and control. We further demonstrate their use in buffer control problems where our SFM-based estimators are evaluated based on data from an actual system.     

An Optimized Content-Aware Authentication Scheme for Streaming JPEG-2000 Images Over Lossy Networks

This paper proposes an optimized content-aware authentication scheme for JPEG-2000 streams over lossy networks, where a received packet is consumed only when it is both decodable and authenticated. In a JPEG-2000 codestream, some packets are more important than others in terms of coding dependency and image quality. This naturally motivates allocating more redundant authentication information for the more important packets in order to maximize their probability of authentication and thereby minimize the distortion at the receiver. Towards this goal, with the awareness of its corresponding image content, we formulate an optimization framework to compute an authentication graph to maximize the expected media quality at the receiver, given specific authentication overhead and knowledge of network loss rate. System analysis and experimental results demonstrate that the proposed scheme achieves our design goal in that the rate-distortion (R-D) curve of the authenticated image is very close to the R-D curve when no authentication is required     

硫酸铈和磷酸处理对铌酸表面酸度及催化活性的影响

用硫酸铈和磷酸对固体铌酸进行了表面处理。表面酸度和TG DTA测定结果表明 ,与未处理的固体铌酸相比 ,处理后表面强酸量提高 3～ 5倍 ,耐受温度由 30 0℃提高到 5 0 0～ 6 0 0℃。用于催化酯化合成二甘醇二苯甲酸酯增塑剂 ,处理后固体铌酸的催化活性和重复使用寿命有明显提高。     

矿石中金的快速测定

研究了活性炭纤维滤布富集分离的条件和解脱方法,并利用微波溶样、液珠萃取比色法测定矿石中的金。该方法的测定范围为(0.5~xx)×10-6,相对标准偏差RSD为3.2%,可用于矿石中金的野外快速测定。     

Failure loads for notched graphite/epoxy laminates with a softening strip

The strengths of two graphite/epoxy notched laminate systems with a softening strip were investigated. The softening strip was created by replacing the 0°-graphite/epoxy plies by a glass/epoxy composite. Experimental results indicated that the use of softening strips could significantly increase the laminate strength. Analysis was performed with finite elements developed using the classical laminated plate theory and was shown to be adequate. A simple point-stress failure criterion was used to predict the strength of notched laminates with softening strips and the result was found to be satisfactory.     

面向对象的程序设计语言CLUSTER86的设计与实现

本文介绍了笔者设计并实现的一种新型的面向对象的程序设计语言,着重讨论了在设计过程中采用的新的概念,并和其它类似语言作了比较.     

用单透镜变换由多模光纤出射的大功率Nd：YAG激光束的特性

根据理论假设，通过选取单透镜的参数和位置，计算说明了单透镜使经由多模光纤出射的大功率Ｎｄ：ＹＡＧ激光束的发射角压缩，光束聚焦效率提高，光束截面场为高斯分布；文中的计算结果符合已知规律，从而说明了理论假设的正确性。     

CIMSCLASS─—面向CIM的零件分类软件开发工具

介绍了一个能为工厂设置零件编码系统和开发零件分类系统的工具系统。该系统能适应用户的具体环境，能对零件的特征信息做较详细的描述和建立相应目标的零件分类系统，从而能在ＧＴ（成组技术）基础上为机械加工零件开发ＣＡＤ／ＣＡＰＰ／ＣＡＭ集成系统提供支持，以满足ＣＩＭＳ的需要。