用于氢化的铜铬氧化物催化剂的研究

通过铜铬氧化物催化剂用于豆油的选择氢化,研究了制备方法及氢化条件对催化剂活性的影响.在所用的五种催化剂中,以Adkins法制备的催化剂活性最好,碳酸氢铵法次之.文中还对催化剂焙烧气氛、焙烧温度、焙烧时间、铜铬原子比对催化剂活性的影响以及氢化温度、催化剂用量、搅拌速度、氢流速等对反应的影响进行了较详细的讨论.     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

Lubricating behavior of iron rhenate and its relation to matching pairs

The iron rhenate was compounded by chemical method, which may be generated during wear process of Fe-Re alloys at elevated temperature. The friction coefficient of iron rhenate has been determined by a pin-on-disc device. The results show that iron rhenate plays role of lubricating at RT-600 °C. The lubricating behavior is related to the matching pairs. The hardness of the materials of matching pairs, compatibility of iron rhenate with materials of matching pairs and surface roughness of disc affect the lubricating behavior of iron rhenate mostly. The principle of matching pairs is proposed. Project supported by the National Natural Science Foundation of China Synopsis of the first author Xiong Dangsheng. associated professor, born in 1960. Current research fields include high-temperature self-lubricating alloys and tribological properties of material.     

Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

精铸件结构优化设计实践

以6种典型的精密铸件为例，利用“6个千方百计”原则对产品结构进行优化设计，同时辅助有限元分析对优化结果进行再验证。通过减少大平面、避免深长孔、采用加强筋等优化措施，有效地避免了夹砂、鼓包、跑火、缩孔、裂纹等铸造缺陷，实现了少无切削和减轻铸件质量。     

西门子S7-200可编程控制器在气化油点火技术中的应用

以西门子S7—200PLC为核心。利用火检探头。温度、压力等传感器，结合STEP 7 MicmwIN V3．1以及ProTool Pro CS工业组态软件完成了对点火过程的自动控制。实现了西门子S7—200PLC在大型发电厂410吨级蒸汽锅炉“气化油直接点燃煤粉技术”中的应用。提高了锅炉点火系统运行的自动化水平。     

双能X射线骨密度仪测定技术研究

以Ｌｕｎａｒ公司ＤＰＸ－Ｌ型双能Ｘ射线骨密度仪为例，研究引起测量误差的主要因素并提出质控措施。用自检模块、腰椎体膜评定仪器的体外测量精度好于１％。对１０位志愿者重复２次测量，体内精度对腰椎，ＭＰＤ（平均百分差）为０．４６，ＣＶ（变异系数）为０．７５；对股骨颈，ＭＰＤ为１．２６、ＣＶ为０．４７；Ｗａｒｄ’ｓ三角区ＭＰＤ为２．０１、ＣＶ为１．１４；大转子ＭＰＤ为１．６６、ＣＶ为０．７２。扫描图像由２位     

InGaAs（P）分别限制应变单量子阱激光器的优化设计

针对较常用的ＩｎＧａＡｓ（Ｐ）分别限制应变单量子阱激光器，给出了为得到最大净增益的优化设计参数。对于激射波长为１．５５μｍ的无应变激光器，最佳的光限制层波长为１．２４μｍ，厚度为１００ｎｍ。当阱材料引入压缩应变后．由于价带的有效状态密度减小，量子阱激光器的微分增益变大，阱深的增大对增大线性增益的效果更加明显．所以最佳光限制层的波长将变短，为１．２０μｍ     

Influence of China‘s WTO Entry on Petroleum Taxation

China has formulated a series of preferential taxation policies for the country 's petroleum enterprises. Those state policies are the important factors influencing reform and development of petroleum enterprises. The taxes turned over to the State by CNPC in 1998, 1999 and 2000 are 31.4 billion yuan, 31.7 billion yuan and 41 billion yuan respectively, accounting for 11.64 percent, 9.06 percent and 10.15 percent of the annual sales income.With China 's entry into WTO, it is necessary for t…