Influence of electroplating conditions on magnetic properties of Fe-36wt.% Ni alloy film

A Fe-Ni soft magnetic film was prepared in sulphate solution by electroplating. The influences of the molar ratio of n [Fe2+ ]/ n [Ni2+ ], current density, bath temperature, pH and L-ascorbic acid concentration on magnetic properties of Fe-Ni alloy film were investigated. The results show that the saturated flux density(BS) of the film increases initially and decreases after it reaches the specific value with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density, bath temperature and pH. However, the relationship between L-ascorbic acid concentration and B S keeps linear. It is observed that the coercive force( Hc) is enhanced with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density and pH. By comparison, when the bath temperature increases, Hc always decreases. With the increase of L-ascorbic acid concentration, the coercive force increases initially and then decreases.     

Measurement of drill point geometry by using laser sensor

Accurate measurement for the drill geometry is essential to drill design and reconditioning. In recent years, a number of non-contact drill measuring instruments, using CCD camera are reported in the literature. But these systems are not suitable in measuring three-dimensional surface, especially the concave ones. As an effectual remedy, a geometry measurement instrument using laser sensor is developed. This paper describes its configuration and calibration. In addition, the measurement method for a drill flute is detailed. Validity of the system and proposed method are demonstrated by an example. The deviations of the data measured from that inspected by using a microscope are no more than 0.0061 mm.     

Some Results for Pythagorean Fuzzy Sets

Pythagorean fuzzy sets (PFSs), originally proposed by Yager (Yager, Abbasov. Int J Intell Syst 2013;28:436–452), are a new tool to deal with vagueness considering the membership grades are pairs satisfying the condition . As a generalized set, PFSs have close relationship with intuitionistic fuzzy sets (IFSs). PFSs can be reduced to IFSs satisfying the condition . However, the related operations of PFSs do not take different conditions into consideration. To better understand PFSs, we propose two operations: division and subtraction, and discuss their properties in detail. Then, based on Pythagorean fuzzy aggregation operators, their properties such as boundedness, idempotency, and monotonicity are investigated. Later, we develop a Pythagorean fuzzy superiority and inferiority ranking method to solve uncertainty multiple attribute group decision making problem. Finally, an illustrative example for evaluating the Internet stocks performance is given to verify the developed approach and to demonstrate its practicality and effectiveness.     

栅元有效共振积分的CUDA算法设计与实现

核反应堆中需要实时精确地计算堆芯和增殖材料的有效共振积分或群截面来实现反应堆的安全控制。整个计算过程因为涉及大量的积分运算和庞大的核素截面数据,采用常规的计算方法,计算时耗相当大。基于统一计算设备架构(CUDA)平台,利用图形处理器(GPU)的计算能力,对整个计算过程进行并行化分解,多线程同时运算,大幅度提升计算速度,降低时耗。实验结果表明,在GPU上并行计算所得结果与原始数据没有明显差异,且加速效果显著。     

Multifocus image fusion method of Ripplet transform based on cycle spinning

The curvelet transform can represent images at both different scales and different directions. Ripplet transform, as a higher dimensional generalization of the curvelet transform, provides a new tight frame with sparse representation for images with discontinuities along C² curves. However, the ripplet transform is lack of translation invariance, which causes the pseudo-Gibbs phenomenon on the edges of image. In this paper, the cycle spinning method is adopted to suppress the pseudo-Gibbs phenomena in the multifocus image fusion. On the other hand, a modified sum-modified-laplacian rule based on the threshold is proposed to make the decision map to select the ripplet coefficient. Several experiments are executed to compare the presented approach with other methods based on the curvelet, sharp frequency localized contourlet transform and shearlet transform. The experiments demonstrate that the presented fusion algorithm outperforms these image fusion works.     

On input‐to‐state stability‐based design for leader/follower formation control with measurement delays

This paper addresses the design of low‐level controllers for leader–follower formations of nonholonomic vehicles in the presence of bounded measurement delays. The concept of input‐to‐state stability is extended to encompass the effect of bounded delays and restrictions on the input. A method is proposed to integrate a Smith predictor in a backstepping design on the basis of nested saturations and nonlinear small‐gain assignment, which allows for time delays in the feedback loop. Robustness analysis under uncertain bounded time delays is provided, and design tradeoffs resulting from the use of bounded controls are discussed. Illustrative simulations are shown to validate the design and robustness analysis in the context of a simple leader–follower trailing control problem. Copyright © 2012 John Wiley & Sons, Ltd.     

基于机器视觉的微片状物厚度检测

针对片状颗粒厚度检测的实际需求,结合机器视觉、图像处理和嵌入式技术,设计与实现了一套基于高性能ARM11的微片状颗粒厚度检测系统。该系统以QT和S3C6410为软硬件平台,提出了利用轮廓提取和最小矩形边界框相结合的方法计算片状颗粒厚度。结果表明,该检测系统具有处理速度快,测量精度高和成本低廉等优点,满足了对颗粒厚度测量的需求。