Effect of broaching on high-temperature fatigue behavior in notched specimens of INCONEL 718

Notches were machined in specimens of INCONEL 718 by a broaching process, where differing broaching runs led to differing extents of subsurface deformation and surface roughness. Fatigue tests were carried out at 600 °C with a trapezoidal loading waveform at 0.25 Hz. The broaching process that led to the more severe subsurface deformation (but lower surface roughness) showed the worst fatigue performance. Analysis of total strain amplitude in the notch root with the aid of an elastoplastic finite-element (FE) model showed that the work hardening related to the subsurface deformation caused by the different broaching can account for the difference in fatigue lives. Differences in initiation and growth behavior were seen for the two broached finishes as well as for broached and subsequently polished samples. These differences are discussed in terms of a change in crack growth initiation and growth mechanisms due to the presence of the work-hardened layer.     

利用LIN节点的温度显示

串行多路传输总线如CAN或LIN可以解决车内因导线过多所带来的许多问题。低成本的LIN总线很适合应用于车门等这些对传输速率要求不高的场合,最高速率为20kbit/s的LIN总线完全可以满足要求。车外温度显示就是这样一个应用实例,外部温度传感器通常布置在后视镜中,数据产生于车门。但是实际显示位置是距此一定距离的车内,LIN总线可使布线简单,因为LIN节点只有3根导线:LIN数据线、电源线和地线。     

Performance of simple response method for the establishment and adjustment of calibration intervals

Managing calibration intervals in order to fulfill requirements of quality-oriented organizations is discussed in this paper. In particular, the simple response method is considered. According to this technique, the interval between successive calibrations is adjusted adaptively on the basis of the outcome of the last calibration process. An original analysis is presented about the properties of such calibration interval handling methods. Finally, directions are given on how to tune its parameters optimally, in order to meet desired levels of long-term measurement reliability.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

Static and pulsed pressures measured using electrically conducting rubbers

A method of measuring static and pulsed pressures using electrically conducting rubber sensors is proposed. The method is based on a change in the volume resistivity of a filled rubber under the action of external pressure. The pressure-induced change in resistance of the rubber sensor is proportional to the applied pressure and can be measured by a bridge circuit. Using this method, it is possible to evaluate the degree of homogeneity of the pressure distribution over a solid surface. This is achieved by distributing rubber sensors over the given surface.     

Markov analysis of qualitative dynamics1

Common sense sometimes predicts events to be likely or unlikely rather than merely possible. We extend methods of qualitative reasoning to predict the relative likelihoods of possible qualitative behaviors by viewing the dynamics of a system as a Markov chain over its transition graph. This involves adding qualitative or quantitative estimates of transition probabilities to each of the transitions and applying the standard theory of Markov chains to distinguish persistent states from transient states and to calculate recurrence times, settling times, and probabilities for ending up in each state. Much of the analysis depends solely on qualitative estimates of transition probabilities, which follow directly from theoretical considerations and which lead to qualitative predictions about entire classes of systems. Quantitative estimates for specific systems are derived empirically and lead to qualitative and quantitative conclusions, most of which are insensitive to small perturbations in the estimated transition probabilities. The algorithms are straightforward and efficient.