Flexural–torsional behavior of thin-walled composite space frames

A general analytical model based on the first-order shear deformable beam theory applicable to thin-walled composite space frames with arbitrary lay-ups under external loads is presented. This model accounts for all the structural coupling coming from the material anisotropy. The seven governing equations are derived from the principle of the stationary value of total potential energy. A displacement-based one-dimensional 14 degree-of-freedom space beam model which includes the effects of shear deformation, warping is developed to solve the problem. Numerical results are obtained to investigate the effects of fiber orientation on flexural–torsional responses of thin-walled composite space frame under vertical load.     

Distance estimation using inertial sensor and vision

A simple distance estimation algorithm using inertial sensors and a mono camera is proposed. Two images of a target are obtained by moving a mono camera. The movement of the camera is estimated using inertial sensors and used as the baseline for the distance estimation. Through experiments, the accuracy of the proposed method is evaluated, where the distance error is 3.9% on average in a few meter ranges.     

Experimental and numerical investigations on the thermal response of multilayer glass fibre/unsaturated polyester/organoclay composite

Organoclay glass fibre reinforced polymer (GFRP) nanocomposites are fabricated using the vacuum assisted resin transfer moulding. The unsaturated polyester resin is prepared with and without organoclay involving mechanical mixing, sonication, dilution solvent and heat treatment. Three levels of organophilic clay content are added, and its influences on the fire performance of composite samples are investigated. A novel numerical procedure combining pyrolysis analysis of the organoclay‐composites and the fire dynamic simulation of the combustion process are developed to validate the thermal responses obtained from the cone calorimetry experiments. Kinetic parameters obtained from the TGA tests and pyrolysis analyses are used as inputs for the models measuring the fire growth index and total heat release. To account for multilayer composite structure and organoclay distribution, three numerical models are proposed including composite (CPS), component (CPN) and CPN‐layer models. While CPS model assumes the homogeneity of the composite, later models consider multilayer effects with uniform (CPN model) or concentrated (CPN‐layer model) distribution of organoclay. Numerical results are compared with experimental ones in terms of total heat release, fire growth index. Finally, the fire resistance and total smoke release of the polyester/glass composites with the addition of organoclay will be evaluated taking into account influences of the fabrication processes.     

Factors affecting energy and nitrogen efficiency of dairy cows: A meta-analysis

A meta-analysis was performed to explore the correlation between energy and nitrogen efficiency of dairy cows, and to study nutritional and animal factors that influence these efficiencies, as well as their relationship. Treatment mean values were extracted from 68 peer-reviewed studies, including 306 feeding trials. The main criterion for inclusion of a study in the meta-analysis was that it reported, or permitted calculation of, energy efficiency (Eeff; energy in milk/digestible energy intake) and nitrogen efficiency (Neff; nitrogen in milk/digestible nitrogen intake) at the digestible level (digestible energy or digestible protein). The effect of nutritional and animal variables, including neutral detergent fiber, acid detergent fiber (ADF), digestible energy, digestible protein, proportion of concentrate (PCO), dry matter intake, milk yield, days in milk, and body weight, on Eeff, Neff, and the Neff:Eeff ratio was analyzed using mixed models. The interstudy correlation between Eeff and Neff was 0.62, whereas the intrastudy correlation was 0.30. The higher interstudy correlation was partly due to milk yield and dry matter intake being present in both Eeff and Neff. We, therefore, also explored the Neff:Eeff ratio. Energy efficiency was negatively associated with ADF and PCO, whereas Neff was negatively associated with ADF and digestible energy. The Neff:Eeff ratio was affected by ADF and PCO only. In conclusion, the results indicate a possibility to maximize feed efficiency in terms of both energy and nitrogen at the same time. In other words, an improvement in Eeff would also mean an improvement in Neff. The current study also shows that these types of transverse data are not sufficient to study the effect of animal factors, such as days in milk, on feed efficiency. Longitudinal measurements per animal would probably be more appropriate.     

Remote sensing techniques to predict salinity intrusion: application for a data-poor area of the coastal Mekong Delta,Vietnam

ABSTRACT

Salinity intrusion is a complex issue in coastal and estuarine areas. Currently, remote sensing techniques have been widely used to monitor water quality changes, ranging from inland river networks to deep oceans. The Vietnamese Mekong Delta is an important rice-growing area, and intrusion of saline water into irrigated freshwater-based agriculture areas is one of the most crucial constraints for agriculture development. This study aimed at building a numerical model to realize the salinity intrusion through the relationship between reflectance from the Landsat-8 Operational Land Imager images and salinity levels measured in situ. A total of 103 observed samples were divided into 50% training and 50% test. Multiple Linear Regression, Decision Trees and Random Forest (RF) approaches were applied in the study. The result showed that the RF approach was the best model to estimate salinity along the coastal river network in the study area. However, the large samples size needed was a significant challenge to circumscribe predicting ability of the RF model. The reflectance has a good correlation with salinity when locations (latitude–longitude) of salinity measured stations were added as a parameter of the Step-wise model with R-square 77.48% in training and 74.16% in test while Root Mean Square Error was smaller than 3.     

The application of polyethyleneimine draw solution in a combined forward osmosis/nanofiltration system

The objective of this study is to investigate the effect of solution chemistry of branched polyethyleneimine (PEI) draw solute and to evaluate the PEI draw solute in a combined forward osmosis (FO)/nanofiltration (NF) system. Pure water was extracted from feed solution using the FO process, and the separation of pure water was achieved by the NF process. Lower molecular weight PEI showed higher water flux than higher molecular weight PEI, due to the lower internal concentration polarization caused by a higher diffusion rate and the easy permeation of pure water by lower viscosity of the draw solution (DS). The FO water flux was determined by the osmotic pressure induced by protonation/deprotonation of PEI, and the reverse draw solute flux was determined by the combination of PEI size due to the speciation and electrostatic interaction between the membrane and PEI. This study shows that the J_s/J_w value of PEI at pH 7 was smaller than those of sodium chloride and magnesium sulfate. The recovery of PEI DS using NF has a higher value (99.4%) than of sodium chloride (20.6%) and magnesium sulfate (97.0%); this means that PEI would be a promising draw solute in an FO–NF combined system for the saline water desalination. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42198.     

Influence of Powder Morphology and Microstructure on the Cold Spray and Mechanical Properties of Ti6Al4V Coatings

The powder microstructure and morphology has significant influence on the cold sprayability of Ti6Al4V coatings. Here, we compare the cold sprayability and properties of coatings obtained from Ti6Al4V powders of spherical morphology (SM) manufactured using plasma gas atomization and irregular morphology (IM) manufactured using the Armstrong process. Coatings deposited using IM powders had negligible porosity and better properties compared to coatings deposited using SM powders due to higher particle impact velocities, porous surface morphology and more deformable microstructure. To evaluate the cohesive strength, multi-scale indentation was performed and hardness loss parameter was calculated. Coatings deposited using SM powders exhibited poor cohesive strength compared to coatings deposited using IM powders. Images of the residual indents showed de-bonding and sliding of adjacent splats in the coatings deposited using SM powders irrespective of the load. Coatings deposited using IM powders showed no evidence of de-bonding at low loads. At high loads, splat de-bonding was observed resulting in hardness loss despite negligible porosity. Thus, while the powders from Armstrong process lead to a significant improvement in sprayability and coating properties, further optimization of powder and cold spray process will be required as well as consideration of post-annealing treatments to obtain acceptable cohesive strength.     

Metallization of Various Polymers by Cold Spray

Previous results have shown that metallic coatings can be successfully cold sprayed onto polymeric substrates. This paper studies the cold sprayability of various metal powders on different polymeric substrates. Five different substrates were used, including carbon fiber reinforced polymer (CFRP), acrylonitrile butadiene styrene (ABS), polyether ether ketone (PEEK), polyethylenimine (PEI); mild steel was also used as a benchmark substrate. The CFRP used in this work has a thermosetting matrix, and the ABS, PEEK and PEI are all thermoplastic polymers, with different glass transition temperatures as well as a number of distinct mechanical properties. Three metal powders, tin, copper and iron, were cold sprayed with both a low-pressure system and a high-pressure system at various conditions. In general, cold spray on the thermoplastic polymers rendered more positive results than the thermosetting polymers, due to the local thermal softening mechanism in the thermoplastics. Thick copper coatings were successfully deposited on PEEK and PEI. Based on the results, a method is proposed to determine the feasibility and deposition window of cold spraying specific metal powder/polymeric substrate combinations.     

Compatibilization and property enhancement of poly(lactic acid)/polycarbonate blends through triacetin-mediated interchange reactions in the melt

Tetrabutylammonium tetraphenylborate (TBATPB) and triacetin were added during extrusion to melt blends of polylactic acid (PLA) and polycarbonate bisphenol A (PC) through a reactive compatibilization approach in order to enhance the materials' mechanical properties and thermal resistance. Dynamic mechanical thermal analysis revealed a new peak attributable to the glass transition temperature (T_g) of the PLA-PC copolymer at a temperature lower than the T_g typical of PC and higher than the T_g of PLA. The results of tensile tests, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy, transmission electron microscopy, size exclusion chromatography, and NMR analysis for the compatibilized and uncompatibilized blends were, on the whole, in agreement with the formation of the PLA-PC copolymer due to the action of the TBATPB and triacetin during the short extrusion time. The mechanical behaviour, morphology, and thermal properties of the PLA/PC compatibilized blends were investigated as a function of composition, with the intention of broadening the utility of these biobased-blends. Finally, a general scheme for the reactions that occur during extrusion was proposed based on the experimental results.