Subthreshold Current Modeling of Stacked Dielectric Triple Material Cylindrical Gate All Around (SD-TM-CGAA) Junctionless MOSFET for Low Power Applications

Silicon - Stacked Dielectric Triple Material Cylindrical Gate All Around (SD-TM-CGAA) Junctionless MOSFET has been explored for low power applications. This paper presents an analytical model of...     

Optically stimulated luminescence (OSL) and laser excited photo luminescence of electron beam treated (EBT) diamonds: Radiation sensitization and potential for tissue equivalent dosimetry

We report the first optically stimulated luminescence (OSL; blue light stimulated luminescence (BLSL) and infrared light stimulated luminescence (IRSL)) results on colored diamonds and present experimental evidence that electron beam treatment (EBT) increases the radiation sensitivity of diamonds to a level that makes them suitable for low level radiation dosimetry. A suite of seven samples was examined. These comprise a white, three brown and three yellow diamond pieces. The FT-IR spectra of these diamonds revealed the nature and concentration of nitrogen impurity. The white diamond was kept as a control. The brown and yellow (with varied saturation) diamonds were irradiated by a 1.7 MeV electron beam. These turned blue/dark green; three of them were then heated in vacuum in the temperature range of 850-900 °C for two hours. Heating turned the irradiated diamonds to lemon yellow, pink, and purple colors. The irradiated and unheated blue samples were designated as 2C and 2D.The control sample, an un-irradiated white type Ia diamond, did not yield any significant IRSL/BLSL with doses up to 100 Gy. The BLSL/IRSL sensitivity of irradiated and heat treated diamonds was very poor, and depended on the heat cycle and hence were not pursued. Sample 2C exhibited significant BLSL and negligible IRSL sensitivity. Sample 2D gave an intense orange red emission under IR excitation as also responded to BLSL. The dose response of the BLSL signal in 2C suggested a minimum detectable dose of ~ 0.1 Gy and its use as a tissue equivalent dosimeter.Based on supporting experiments such as laser excited photoluminescence, we suggest that the BLSL process in 2C is primarily driven by carbon vacancies, which release a mobile hole when excited by GR2 band in the blue region. BLSL intensity exhibited a maximum around 285 °C. Given that TL glow peak also occurs near this temperature and that the nitrogen-interstitial carbon (N-Ci) complex also forms at this temperature (as reported in the literature), and it appears that the e-h recombination at sites with N-Ci complex could be involved in BLSL production. Laser excited photoluminescence (PL) at wavelengths 325, 514 and 785 nm and absorption spectra in UV-Visible range gave insights into the contrasting BLSL/IRSL responses of 2C and 2D. These differences were due to differences in nitrogen impurity complexes and the concentration of carbon vacancies produced by EBT in 2C and 2D. In 2D, the presence of Ni as NE8 center (four nitrogens coordinated to Ni) giving 800 nm emission on 785 nm excitation, appeared to suppress BLSL and sensitize IRSL in the orange window.     

Amorphous silicon–carbon based nano-scale thin film anode materials for lithium ion batteries

The buffering effect of carbon on the structural stability of amorphous silicon films, used as an anode for lithium ion rechargeable batteries, has been studied during long term discharge/charge cycles. To this extent, the electrochemical performance of a prototype material consisting of amorphous Si thin film (∼250 nm) deposited by radio frequency magnetron sputtering on amorphous carbon (∼50 nm) thin films, denoted as a-C/Si, has been investigated. In comparison to pure amorphous Si thin film (a-Si) which shows a rapid fade in capacity after 30 cycles, the a-C/Si exhibits excellent capacity retention displaying ∼0.03% fade in capacity up to 50 cycles and ∼0.2% after 50 cycles when cycled at a rate of 100 μA/cm² (∼C/2) suggesting that the presence of thin amorphous C layer deposited between the Cu substrate and a-Si acts as a buffer layer facilitating the release of the volume induced stresses exhibited by pure a-Si during the charge/discharge cycles. This structural integrity combined with microstructural stability of the a-C/Si thin film during the alloying/dealloying process with lithium has been confirmed by scanning electron microscopy (SEM) analysis. The buffering capacity of the thin amorphous carbon layer lends credence to its use as the likely compliant matrix to curtail the volume expansion related cracking of silicon validating its choice as the matrix for bulk and thin film battery systems.     

Evaluating Esters Derived from Mustard Oil (<Emphasis Type="Italic">Sinapis alba</Emphasis>) as Potential Diesel Additives

Biodiesel was produced from mustard oil utilizing transesterification with methanol, ethanol, propanol, and butanol to evaluate the characteristics of mustard biodiesel as an additive to regular diesel. Mustard oil was transesterified with alcohol at 6:1 alcohol to oil molar ratio, using KOH as a catalyst at 1 wt%. The maximum ester content achieved by this method was only 66%. Distillation was then used to purify the ester, raising the ester content to 99.8%. Alternatively, mustard oil methyl ester (MME) can be mixed with esters derived from canola oil or soybean oil to achieve an ASTM quality biodiesel. Biodiesel derived from mustard showed great potential as lubricity additive for regular diesel fuel. With an addition of 1% MME, lubricity of diesel fuel was improved by 43.7%. It is also found that methyl ester is the best lubricity additive among all esters (methyl-, ethyl-, propyl-, and butyl-ester). MME can be used at −16 °C without freezing whereas monounsaturated compounds (oleic, eicosenoic, and erucic esters) largely present in esters derived from mustard oil can tolerate −42 to −58 °C. Monounsaturated esters derived from higher alcohols such as butyl alcohol demonstrated a superior low temperature tolerance (−58 °C) as compared to that derived from lower alcohol such as methyl alcohol (−42 °C).     

Dielectric barrier discharge plasma induced surface modification of polyester/cotton blended fabrics to impart water repellency using HMDSO

Continuous treatment of polyester/cotton blended fabric samples was carried with hexamethyldisiloxane (HMDSO) plasma on the pilot scale atmospheric pressure plasma reactor. The mixture of helium and argon was used as carrier gas for generating dielectric barrier discharge plasma. The effect of discharge power and treatment time on the water repellent properties of samples were evaluated with contact angle (CA) and spray test measurements. Spray test and CA results showed improved resistance to wetting with water. The effect of discharge conditions on the surface morphology and surface chemistry of plasma treated samples were investigated by scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopic analysis, respectively. The presence of Si‐O‐Si and Si‐CH₃ groups in the structure of plasma polymer deposited at the surface of P/C samples was revealed by FTIR spectroscopy. Further, structural differences in HMDSO plasma polymer deposited under different discharge conditions were reported with reference to organic/inorganic nature of plasma polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Oriented crystallization in fiber formation: Inferences from the structure and properties of melt spun syndiotactic polypropylene filaments

In processes, such as melt spinning, the crystallization behavior of syndiotactic polypropylene (sPP) is found to be substantially different from that of most other linear polymers. The anisotropic stress field in such processes leads invariably to extension as well as alignment (orientation) of the chains in the melt, both of which contribute usually to dramatic enhancement in the rate of crystallization. However, since the primary structure of the sPP chain in its most preferred crystal form is comprised of a “coiled helical,” ? (T₂G₂)₂? , sequence, stress‐induced chain extension can lead to conformational sequences that are not favorable for crystallization in this form. As a consequence, process conditions that generate higher stress levels can cause a diminution in the rate of crystallization of this polymer. Such conformation‐related aspects of oriented crystallization of sPP have been addressed through an analysis of the structure and properties of melt‐spun fibers, produced over a range of spinning speeds. The results serve to identify a refinement that is needed in current models of oriented crystallization and also a mechanism to promote the nucleation of crystallization of sPP. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2305–2317, 2001     

Physico‐mechanical properties of nano‐polystyrene‐decorated graphene oxide–epoxy composites

Nano‐polystyrene (nPS)‐decorated graphene oxide (GO) hybrid nanostructures were successfully synthesized using stepwise microemulsion polymerization, and characterized using Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), field‐emission scanning electron microscopy and transmission electron microscopy. XRD and FTIR spectra revealed the existence of a strong interaction between nPS and GO, which implied that the polymer chains were successfully grafted onto the surface of the GO. The nPS‐decorated GO hybrid nanostructures were compounded with epoxy using a hand lay‐up technique, and the effect of the nPS‐decorated GO on the mechanical, thermal and surface morphological properties of the epoxy matrix was investigated using a universal tensile machine, Izod impact tester, thermogravimetric analysis and contact angle measurements with a goniometer. It was observed that in the epoxy matrix, GO improved the compatibility. © 2017 Society of Chemical Industry     

An approach to eliminate stepped features in multistage incremental sheet forming process: Experimental and FEA analysis

Incremental sheet forming (ISF) is a recently developed manufacturing technique. In ISF, forming is done by applying deformation force through the motion of Numerically controlled (NC) single point forming tool on the clamped sheet metal blank. Single Point Incremental sheet forming (SPISF) is also known as a die-less forming process because no die is required to fabricate any component by using this process. Now a day it is widely accepted for rapid manufacturing of sheet metal components. The formability of SPISF process improves by adding some intermediate stages into it, which is known as Multi-stage SPISF (MSPISF) process. However during forming in MSPISF process because of intermediate stages stepped features are generated. This paper investigates the generation of stepped features with simulation and experimental results. An effective MSPISF strategy is proposed to remove or eliminate this generated undesirable stepped features.     

Synthesis,characterization and comparative OFET behaviour of indenofluorene–bithiophene and terthiophene alternating copolymers

The synthesis of alternating copolymers of tetraalkylindenofluorene with bithiophene and terthiophene using Suzuki polycondensation route is reported. We report on the optical and electrochemical properties of these copolymers. AFM analysis of the microscopic morphology of thin deposits showed that the copolymer with terthiophene units produced the more ordered films, with well-defined fibrillar structures, resulting from highly-regular dense packing due to strong π–π interchain interactions, in contrast to the amorphous bithiophene copolymer. Upon testing these materials in FETs the terthienyl copolymers displayed the higher charge mobilities among the studied compounds, with values of over 10^?4 cm² V^?1 s^?1 being obtained.