Two-level optimal output feedback stabilizer design

Design of two-level system stabilizers is considered using an optimal reduced-order model whose state variables are torque angles and speeds. The reduced-order model retains their physical meaning and is used to design a two-level linear feedback controller that takes into account the realities and constraints of the electrical power systems. The two-level control strategy is used, and a global control signal is generated from the output variables to minimize the effect of interaction. The effectiveness of this controller is evaluated, and an example, the multimachine system, is given to illustrate the advantages of the proposed method. The responses of the system with the two-level scheme and optimal reduced order scheme are included for comparative analyses     

Kinetics of AuSn4 migration in lead-free solders

The relatively fast diffusion of Au atoms in eutectic PbSn matrix is considered one of the contributing factors to the Au embrittlement problem. In this study, we further investigated the Au embrittlement problem in high-Sn solders. Experimentally, Sn3.5Ag (wt.%) spheres with 500-μm diameter were soldered over the Au/Ni soldering pads. It was found that some of the AuSn₄ needles that formed after reflow inside the solder migrated back to the solder/pad interface during thermal aging. However, the migration kinetics in high-Sn solders was slower compared to that in eutectic PbSn. The difference in migration kinetics of AuSn₄ in eutectic PbSn and SnAg was ascribed to the difference in the magnitudes of the Au flux and the Ni flux. In eutectic PbSn, the Au flux was much greater than that of the Ni flux, and the Au and Ni flux were in the same order of magnitude in eutectic SnAg. The relative magnitude of the Au and Ni flux changed in eutectic PbSn and SnAg because the homologous temperatures of PbSn and SnAg were different.     

A Shortcut Method for Estimating the HETP of Structured Packed Distillation Columns at Elevated Pressure

A shortcut model is developed for predicting the HETP of a structured packed distillation column operating at elevated pressure. The proposed model incorporates the geometrical parameters of the packing, physical properties of the vapor and liquid phases, and the hydrodynamics of the two‐phase flow. The proposed model is tested and validated by comparing the predicted results with the present experimental data and some published HETP data. The results show that the proposed model can predict the experimental data with a deviation smaller than 20 %.     

《石油沥青纸胎油毡》国家标准的修订

《石油沥青纸胎油毡》国家标准进行了第三次修订。本文介绍了修订的理由、修订的内容与依据，并与国内外同类产品标准进行了比较。     

A Single-Die 124 dB Stereo Audio Delta-Sigma ADC With 111 dB THD

This paper presents a highly power-efficient stereo delta-sigma ADC designed for high-precision applications, with measured inter-channel isolation over 130 dB. This design adopts a single-loop, fifth-order, 33 level analog modulator with positive and negative feedforward paths. An interpolated multilevel quantizer with unevenly weighted quantization levels replaces a conventional 5-bit flash type quantizer. These new techniques suppress signal dependent energy inside the delta-sigma loop, reduce internal channel coupling and power consumption. Manufactured in 0.35 mum double poly, three metal CMOS process, the single-die chip includes two analog modulators, on-chip bandgap reference circuit, decimation filter and serial interface circuits. The core die area is around 14.8 mm². The ADC achieves 124 dB dynamic range (A-weighted), -111 dB THD over 20 kHz bandwidth. Total power consumption is less than 330 mW.     

Electrochemical determination of estradiol using a poly(l-serine) film-modified electrode

A thin film of poly(l-serine) was prepared via electropolymerization for the determination of trace levels of estradiol. In pH 5.0 phosphate buffer, l-serine was oxidized during the cyclic potential sweeps between −0.60 and 2.0 V, forming a thin film at the electrode surface. The electrochemical behavior of estradiol was investigated. The oxidation peak potential of estradiol shifts negatively at the poly(l-serine) film-coated glassy carbon electrode (GCE) compared with that at the bare GCE. Otherwise, the oxidation peak current greatly increases at the poly(l-serine) film-modified GCE. These phenomena suggest that the poly(l-serine) film exhibits catalytic activity towards the electrochemical oxidation of estradiol. Based on this, a sensitive, rapid and simple electrochemical method was proposed for the determination of estradiol. The limit of detection is evaluated to be 2.0 × 10⁻⁸ mol L⁻¹. Finally, this method was successfully used to determine estradiol in blood serum.     

Study on the long‐term thermal‐oxidative aging behavior of polyamide 6

The long‐term thermal‐oxidative aging behavior of polyamide 6 (PA6) was studied by comparison with the stabilized sample in this work. The variation of mechanical properties of the pure and the stabilized samples of PA6 with aging time at 110°C, 130°C, and 150°C were investigated, respectively. The aging mechanism of PA6 under heat and oxygen was studied in terms of the reduced viscosity, crystallization behavior, dynamic mechanical behavior, and chemical composition through the methods of polarized light microscopy (PLM), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), X‐ray photoelectron energy spectrum (XPS), and so on. The results indicated that at the initial stage of aging, the molecular crosslinking reaction of PA6 dominated resulting in the increase of the mechanical strength, reduced viscosity, and the glass transition temperature of the sample. And the molecular degradation dominated in the subsequent aging process resulting in the decrease of the melting temperature, the increase of the crystallinity, and the formation of the oxides and peroxides products. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008