Strain-induced crystallization,Part IV: Induction time analysis

The empirical equation, 1/t_i = Ae^Ei/RT, which expresses the exponential dependence of the reciprocal of crystallization induction time, t_i, has been analyzed and shown to be equivalent to the nucleation rate equations derived earlier in Part III (1). Consequently we have used the t_i measurements obtained earlier by Krueger and Yeh to calculate not only the nucleation rate enhancements but also the melting point elevations, the relative crystal thickness changes and molecular coil extension ratios of shear-crystallization polyethylene. It is shown that polyethylene when crystallized between 129 and 131°C at shear rates between 1.56 and 9.70 sec^?1 can have melting point increases of 4.2 to 7.2°C and crystal thickness decreases of 20 to 25 percent, when compared to those crystallized at 130°C in the quiescent state. The predicted “coil” extension in the melt just prior to shear-induced crystallization ranges between 21 and 36 percent. The results of these analyses as well as those on nucleation rates of polyethylene oxide are discussed in detail.     

管内阴极保护的数值模拟(Ⅱ)——有限差分法计算大口径管内的电位分布

采用有限差分技术对大口径输水管道管内阴极保护电位分布进行计算,理论值与实测值符合得较好。     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Thermal conversion (visbreaking) of heavy Iraqi residue

A heavy Iraqi residue was thermally cracked using a soaker visbreaking process at temperatures between 435 and 480 °C, with a range of residence times of 43–109 s in the coil and 151–379 s in the soaker. The pressure was kept constant at 7 bar. Visbroken products were characterized, evaluated and fractionated into light, middle and heavy cuts. The stability of the visbroken products was compared with that of the original feedstock. Also an activation energy was calculated for the visbreaking process and related to the severity of the process. The results obtained show that the conditions used were not severe and could be applied to obtain a required conversion depending on the uses of the products.     

A comprehensive study on RF MEMS switch

This paper emphasis on state-of-the-art of the earlier until the current trend and demand, principles, design considerations, key performance and fabrication technology of RF MEMS switch devices developed over the past few years. RF MEMS switch performance and features such as actuation voltage, insertion loss, isolation and ease with cost of fabrication and applications are compared and discussed.     

Sorption of Aniline by Montmorillonite

Sorption of aniline by montmorillonite was studied by infra-red, X-ray diffraction and differential thermal analysis methods. The amount of aniline sorbed and the type of bonding depend upon the interlayer cations: anilinium, H⁺- and Al³⁺- give anilinium aniline ions, NH₄⁴-ammonium aniline ions, alkalis and alkaline earths except Cs are bonded to aniline through water bridges and transition metal cations are coordinated to aniline partly directly and partly through water bridges. Sorption does not occur in the complete absence of water.     

A polyamide-silica composite prepared by the sol-gel process

Summary A new kind of organic-inorganic hybrid composite was prepared by means of the sol-gel process. The polymer employed was a mixed-isomer aromatic polyamide having good solubility and thermal stability. The silica constituting the inorganic phase was produced by the hydrolysis and condensation of tetramethoxysilane. The bonding between the phases involved aminophenyl-trimethoxysilane, in which the amino group can react with the phthaloyl chloride end-capped polymer, and the methoxysilane groups undergo hydrolysis. The composition of these composites was varied by changing the linear polymer chain length and relative amount of tetramethoxysilane. The gelation time was found to range from a few minutes to several days. Thermogravimetric analyses showed that decomposition starts at approximately 450 °C. Thin films cast from materials having a relatively high silica content were opaque and rigid, but those with low silica content were flexible and transparent.     

Electrooxidation of acetaldehyde on carbon-supported Pt, PtRu and Pt3Sn and unsupported PtRu0.2 catalysts: A quantitative DEMS study

The oxidation of acetaldehyde on carbon supported Pt/Vulcan, PtRu/Vulcan and Pt₃Sn/Vulcan nanoparticle catalysts and, for comparison, on polycrystalline Pt and on an unsupported PtRu_0.2 catalyst, was investigated under continuous reaction and continuous electrolyte flow conditions, employing electrochemical and quantitative differential electrochemical mass spectroscopy (DEMS) measurements. Product distribution and the effects of reaction potential and reactant concentration were investigated by potentiodynamic and potentiostatic measurements. Reaction transients, following both the Faradaic current as well as the CO₂ related mass spectrometric intensity, revealed a very small current efficiency for CO₂ formation of a few percent for 0.1 m acetaldehyde bulk oxidation under steady-state conditions on all three catalysts, the dominant oxidation product being acetic acid. Pt alloy catalysts showed a higher activity than Pt/Vulcan at lower potential (0.51 V), but do not lead to a better selectivity for complete oxidation to CO₂. C–C bond breaking is rate limiting for complete oxidation at potentials with significant oxidation rates for all three catalysts. The data agree with a parallel pathway reaction mechanism, with formation and subsequent oxidation of CO_ad and CH _{x, ad} species in the one pathway and partial oxidation to acetic acid in the other pathway, with the latter pathway being, by far, dominant under present reaction conditions.     

Development and characterization of silicone/phosphorus modified epoxy materials and their application as anticorrosion and antifouling coatings

Epoxy resin is chosen for our present study owing to its exceptional combination of properties such as easy processing, high safety, excellent solvent and chemical resistance, toughness, low shrinkage on cure, good electrical, mechanical and corrosion resistance with excellent adhesion to many substrates. This versatility in formulation made epoxy resins widely applied for surface coatings, adhesives, laminates, composites, potting, painting materials, encapsulant for semiconductor and insulating material for electric devices. There are numerous paint/coating systems based on epoxy resin available for corrosion and fouling prevention. They however are not completely satisfactory in field applications, where high corrosion, fouling and flame resistance are required. The demand for epoxy resin as corrosion/fouling resistant coatings is restricted mainly due to its inferior characteristics like poor impact strength, high rigidity, and moisture absorbing nature besides inadequate flame retardant properties. It is for this reason that silicones and phosphorus-based compounds are used as modifier in this work by intercrosslinking network mechanism (ICN) to obtain epoxy resin with desired properties ideally suitable for field applications for preventing corrosion and fouling with flame retardantancy. The present work involves the development of solvent free silicone/phosphorus modified epoxy coating systems, since solvent free coating systems are widely used for numerous applications due to their lower cost per unit film thickness, freedom from fire and pollution hazard and ability to provide better performance. For the development of coating systems, epoxy resin (X) serves as base material, hydroxyl terminated polydimethylsiloxane (HTPDMS) as modifier, γ-aminopropyltriethoxysilane (γ-APS) as crosslinking agent and dibutyltindilaurate (DBTDL) as catalyst. Polyamidoamine (A), aromatic amine adducts (B) and phosphorus-containing diamine (C) were used as curing agents. The study also describes the evaluation of corrosion resistant behaviour of unmodified epoxy and siliconized epoxy coatings by potentiodynamic polarization method, electrochemical impedance spectroscopy (EIS), salt-spray and antifouling tests. The results are discussed.