A comparative analysis of fuzzy logic and PI speed control in high-performance AC drives using experimental approach

One of the frequently discussed applications of artificial intelligence in motion control is the replacement of a standard proportional plus integral (PI) speed controller with a fuzzy logic (FL) speed controller. Regardless of all the work, it appears that a thorough comparison of the drive behavior under PI and FL speed control is still missing. This paper attempts to fill in this gap, by providing an in-depth comparison of operation of a vector-controlled permanent-magnet synchronous motor, using at first an experimental rig. Speed responses, obtained under PI and FL speed control, are recorded and compared for a variety of operating conditions. The transients studied include response to a large step speed command from standstill with nominal inertia and an increased inertia, response to small step speed reference change, and response to step load torque application. The transient behavior is examined for various initial speed settings, so that a thorough comparison is enabled. Experimental results are further supplemented with a set of simulation results, obtained using a different permanent-magnet machine and a different FL controller. Better generalization of the results is enabled in this way. It is shown that superiority of the FL speed control is less pronounced than it is often portrayed in the literature on the basis of limited comparisons. Indeed, in a number of cases, PI speed control provides a superior speed response.     

The Cooperative Molecular Field Effect

Two‐dimensional arrangements of molecules can show remarkable cooperative electronic effects. Such effects can serve to achieve direct electronic sensing of chemical and physical processes via electrostatic effects, i.e., without transfer of charge or matter between the locus of sensing and that of detection.     

A wideband orthogonal-mode junction using a junction of aquad-ridged coaxial waveguide and four ridged sectoral waveguides

A wideband orthogonal-mode junction (OMJ) using a quad-ridged circular coaxial waveguide and four single-ridged sectoral waveguides is described. The new structure is used for extracting a wide lower band signal from a coaxial dual-band feed. Theoretical results show that the broadband incoming signal in the quad-ridged coaxial waveguide can be coupled to four single-ridged sectoral waveguides with low reflection. The new structure transforms a complex system to a simple single-ridged sectoral waveguide where multi-band separation can be accomplished by a number of means. The transformation eliminates the interference among the excitation sources and enables the accurate mathematical modeling of the complete system possible     

The corrosion behavior of sputter-deposited aluminum-tungsten alloys

Thin films on aluminum-tungsten alloys were prepared by co-deposition of pure aluminum and pure tungsten, each sputtered by an independently controlled magnetron source, on glass and sapphire substrates. Completely amorphous films were obtained in the Al₈₀W₂₀-Al₆₇W₃₃ composition range. Passivity and corrosion behavior of amorphous Al-W alloys were investigated in 1 M deaerated hydrochloric acid solution using polarization and impedance spectroscopy measurements and have been correlated with the properties of pure alloy components. Tungsten and sputter-deposited Al-W thin films are inherently passive materials while aluminum undergoes pitting corrosion in hydrochloric acid solution. The passive film formed at the OCP on each alloy possesses excellent electric and dielectric properties comparable to those of the isolating film on tungsten. The absolute impedance increases with increasing tungsten content in the alloy. According to electrochemical polarization measurements, alloying Al with W in solid solution significantly enhances the material's resistance to pitting corrosion by shifting the breakdown potential above 2000 mV (Al₆₇W₃₃) and lowering the corrosion rate at the OCP by more than two orders of magnitude. The most likely mechanism explaining the passivity of amorphous Al-W alloys, the Solute Vacancy Interaction Model (SVIM), involves the formation of complexes between highly oxidized solute atoms (W⁺⁶) and mobile cation vacancies, which restrict the transport of Cl⁻ through the oxide film and inhibit its breakdown in hydrochloric acid solution. The role that film stress relaxation effects and microscopic defects in amorphous Al-W films, of the some composition, and deposited on various substrates play in their corrosion resistance is discussed.     

Fringe probing of an evaporating microdroplet on a hot surface

The phenomenon of droplets impacting and evaporating on a hot surface is of interest in many areas of engineering. Quantitative measurement of these processes provides great help to reveal the physics behind. A novel technique was developed to quantitatively measure the volume evolution and contact diameter of an evaporating microdroplet on a hot surface utilizing interference fringe scattering method. In this method, fine fringes produced by the interference of two coherent laser beams was scattered by the droplet and projected onto a screen. The profile and volume of the droplet can be derived from the spatial fringe spacing on the screen. The number of total fringes measurable on the screen was used to determine the instantaneous contact diameter of the microdroplet. Validation experiments demonstrated that the measurement errors are less than ±5% and ±1% for microdroplet volume and contact diameter, respectively. By using this method, the dynamic of droplet impingement, evaporation and boiling using ethanol, pure water and water solution of a surfactant (sodium dodecyl sulfate) with impact velocity of 7.5 m/s and diameters ranged from 0.19 to 0.46 mm were investigated.     

The availability of daylight from tropical skies—a case study of Malaysia

In Malaysia, no long-term daylight data are measured. It was only recently that the need to measure the availability of daylight became urgent when the importance of daylighting in buildings was rediscovered. The hourly daylight availability has been simulated for the Malaysian sky using daylight modelling techniques based on empirical and measured solar irradiation and cloud cover data. This paper presents the techniques involved in producing exterior illuminance data. These data were then compared with measured illuminance at Shah Alam and Bangi, Malaysia. The global illuminance levels are generally high, with values exceeding 80,000 lux at noon during the months when solar irradiation is highest. Even during the months when the ground receives less solar irradiation, the peak illuminance can reach 60,000 lux. Applications and uses of such data are in daylighting design, both for visual and thermal comfort, task illuminance and energy-conscious design of buildings. Recommendations are made at the end of the paper on the various climatic data that are required to be measured for overall daylighting design applications.