On-line estimation of kinetic parameters in anaerobic digestion using observer-based estimators and multiwavelength fluorometry.

Observer-based estimators (OBE) were used for estimation of state variables and kinetic parameters in an anaerobic digestion (AD) process. A simplified first-order model with time-varying kinetic parameters was used to design an OBE for kinetic parameter estimation. This approach was validated on a laboratory-scale anaerobic reactor equipped with a multiwavelength fluorometer for on-line measurements of COD and VFA concentrations in the reactor effluent. The proposed estimators provide continuous adjustment of kinetic parameters and can be used for predictions of state variables between samples acquisition and during sensor failure.     

Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Comprehensive heat exchange model for a semiconductor laser diode

By measuring the total energy flow from an optical device, we can develop new design strategies for thermal stabilization. Here we present a comprehensive model for heat exchange between a semiconductor laser diode and its environment that includes the mechanisms of conduction, convection, and radiation. We perform quantitative measurements of these processes for several devices, deriving parameters such as a laser's heat transfer coefficient, and then demonstrate the feasibility of thermal probing for the nondestructive wafer-scale characterization of optical devices.     

Experimental studies of the bond response of three-wire strands and some influencing parameters

The bond behavior of prestressing strands is of great importance for the capacity of precast prestressed concrete structures. In the present study, the bond behavior of three-wire strands, and some influencing parameters, were examined by means of steel encased pull-through and push-in tests. The three mechanisms: adhesion, friction and other mechanical actions were found to be present at the strand-concrete interface at different slip values. The results from the experiments showed that the micro roughness of the strand surface strongly affected the initial bond response of the strand, that is the adhesion in the interface. The maximum bond capacity of indented three-wire strands was found to be directly connected to the geometric properties of the strand indents. The influence of the concrete strength on the bond capacity of the strand was hard to interpret. However, the density of the concrete matrix was found to be a better parameter for determine the influence of the concrete rather than the compressive strength.     

Metalorganic chemical vapor deposition of silver thin films for future interconnects by direct liquid injection system

Deposition of Ag films by direct liquid injection-metal organic chemical vapor deposition (DLI-MOCVD) was chosen because this preparation method allows precise control of precursor flow and prevents early decomposition of the precursor as compared to the bubbler-delivery. Silver(I)-2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octanedionato-triethylphosphine [Ag(fod)(PEt₃)] as the precursor for Ag CVD was studied, which is liquid at 30 °C. Ag films were grown on different substrates of SiO₂/Si and TiN/Si. Argon and nitrogen/hydrogen carrier gas was used in a cold wall reactor at a pressure of 50–500 Pa with deposition temperature ranging between 220 °C and 350 °C. Ag films deposited on a TiN/Si diffusion barrier layer have favorable properties over films deposited on SiO₂/Si substrate. At lower temperature (220 °C), film growth is essentially reaction-limited on SiO₂ substrate. Significant dependence of the surface morphology on the deposition conditions exists in our experiments. According to XPS analysis pure Ag films are deposited by DLI-MOCVD at 250 °C by using argon as carrier gas.     

The anisotropic effect of a weak magnetic field on the photoconductivity of C<Subscript>60</Subscript> single crystals

The effect of crystal orientation on the photogeneration of free charge carriers was studied for C₆₀ single crystals in a weak magnetic field. The photoconductivity sharply depends on the orientation of magnetic field with respect to the crystallographic directions, showing a 5–8% increase for seven axes of the C₆₀ crystal.     

State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

我国上市公司股票评级研究——财务结构模型分析法在股票市场中的应用

目前,我国股票市场上的股票评级尚处于探索阶段,评级时多采用专家法或历史法,而对于影响股票评级的各因素的确定以及因素间的相互作用缺乏定量分析。研究将结构模型应用到我国股票市场的股票评级中,建立关于我国股票评级的财务结构模型;分析各个因素对股票评级的影响;建立股票评级经验模式值。     

针对不同地质目标的叠前时间偏移成像解释评价

随着计算机硬件和地震勘探成像技术的发展，叠前时间偏移正逐步替代常规的NMO加DMO加叠后时间偏移成为地震数据成像处理方法的主流。但对于不同的地质目标，叠前时间偏移的成像效果是否优于常规NMO加DMO加叠后时间偏移的成像效果呢？为此，从地震数据成像处理方法、处理流程和处理参数等方面进行了讨论，并基于某地区三维数据常规处理结果和叠前时间偏移处理结果，针对不同地质目标进行了剖析与评价。认为：叠前时间偏移成像的垂向分辨率较常规处理明显降低，但对于空间波阻抗变化明显的河流和断层，叠前时间偏移成像的空间分辨率要高于常规处理；对于小于1／4波长的叠置薄储层，叠前时间偏移成像的垂向和空间分辨率低于常规处理结果。