Contacting modes and behaviour classification of gas—solid and other two-phase suspensions

An attempt is made to extend schemes for classifying the behaviour of gas—solid contacting modes and other two-phase systems. The regime diagram approach of Reh (1971) is modified and extended to cover the operating regions of common reactors and contactors where a gas flows upwards through a bed of solids including fixed and moving packed beds, conventional fluidized beds, circulating beds, spouted beds, and pneumatically conveyed suspensions. New boundaries are proposed between groups A and B and between groups B and D of the Geldart (1972, 1973) powder classification scheme. These boundaries reflect more recent data and allow the classification scheme to be used for gases other than air and for temperatures and pressures other than atmospheric.     

Comfort limits for asymmetric thermal radiation

Groups of 32 and 16 subjects of both sexes were exposed in an environmental chamber to radiant asymmetry caused by a cool wall, a warm wall, and a cool ceiling. Each subject was tested individually while seated and clothed at 0.6 clo. During each 3.5-hour experiment the subject was exposed to six radiant temperature asymmetries. He was asked whether and where he experienced any local cool or warm sensation, and whether it was felt to be uncomfortable. During the entire experiment he was kept thermally neutral by changing the air temperature according to his wishes.For cool walls, warm walls, and cool ceilings curves have been established showing the percentage of dissatisfied subjects as a function of the radiant asymmetry. Radiant asymmetry at a warm wall caused less discomfort than a cool wall. A cool ceiling caused less discomfort than a warm ceiling. Accepting that 5% of the subjects may feel uncomfortable. a radiant temperature asymmetry of 10°C is allowable at a cool wall, 23°C at a warm wall, and 14°C under a cool ceiling. A previous study showed that 4°C is allowable under a warm ceiling. Radiant asymmetry had no significant impact on the operative temperatures preferred by the subjects. No significant differences were observed between the responses of men and women exposed to radiant asymmetry.     

Relationship between structure parameters and chemical properties in some MPS3 layered phases

Cationic thermal motions in the MPS₃ have been related to substitution abilities in this layer family. They have also been correlated to the crystal field stabilization energy. These considerations explain why some MPS₃ materials may or may not undergo a low temperature substitution intercalation reaction. From interatomic distances comparisons, the bond between (PS₃) groups in the anionic (P₂S₆)^4? octahedra, is found to be easily stretched upon cation substitution. Cationic radii follows the expected variation according to their high spin configuration in octahedral sulfur environment.     

Quantitative determination of aflatoxin B1 in chick liver

A method for the rapid and quantitative determination of aflatoxin B1 from small quantities of liver, around 1-2 g, is described. The extraction procedure involves acidification to pH 2 of the aqueous liver homogenates, extraction with chloroform: acetone and HPLC-fluorimetric detection after derivatization with trifluoroacetic acid. Quantitative recovery of aflatoxin B1 from chick liver was achieved and detection at levels of 0.2-1 ppb was proved feasible. The aflatoxin B1 concentration in chick liver after oral administration is also shown.     

Toughening of Dental Porcelain by Tetragonal ZrO2 Additions

The effect on mechanical behavior of ZrO₂ additions to a dental porcelain was investigated. The ZrO₂ was introduced into the glassy matrix phase of the porcelain by refritting the all-glass porcelain constituent. X-ray diffraction indicated that a sizeable fraction of the ZrO₂ was retained in the tetragonal form after the porcelain was fired. Zirconia additions to the porcelain produced substantial improvements in fracture toughness, strength, and thermal shock resistance.     

Elastic-Plastic Contact Damage in a Lead Lanthanum Zirconate Titanate

Spherical indenters were used to produce elastic-plastic contact damage in a lead lanthanum zirconate titanate (PLZT) under conditions of quasi-static and impact loading. The extent of radial cracking produced under both loading conditions showed good correlation with the response predicted by an earlier fracture mechanics analysis for quasi-static conditions. Calculated radial crack lengths corresponding to conditions of impact loading exhibited excellent agreement with experimentally measured values. The dynamic hardness of the PLZT was determined to be ∼ 1.5 times the quasi-static hardness. Differences in the radial crack lengths produced under the two loading conditions were attributed primarily to this difference in hardness response.     

Dissolution Profiling of Six Modified-Release Oral Solid Dosage Forms

Dissolution testing was conducted for six non-combination, single entity, modified-release oral solid dosage forms. Dissolution medium was water and 0.1 N hydrochloric acid. USP Apparatus 1 and Apparatus 2 were used arid were rotated at either 50 or 100 rpm. A complete dissolution profile was obtained for all six dosage forms based on their stated dosing interval, D. The three strengths of Theo-dur tablets, Norpace CR 150 mg capsules, and the two strengths of Chlor-trimeton tablets passed the Compendial Case One requirements (USP XXI, 2S, 1906). Thorazine spansules and Quinidex tablets were unable to meet the specifications with water as the dissolution medium; the latter showed improved dissolution character in 0.1 N hydrochloric acid. Tenuate Dospan 75 mg tablets showed good release characteristics in water when the authentic (dosing interval (D = 24 hours) was changed to a modified dosing interval of D* = 12 hours. All dissolution aliquots were assayed by UV absorbance measurements at the absorbance maximum for each drug and were also checked for excipient interference. Newer drugs appearing on the market will be more likely candidates for meeting compendial specifications; modified-release pharmaceuticals that appeared before the new specifications may have to be allocated specifically expanded window percentages.     

Dynamic viscosities of mixtures of n-butyraldehyde and isobutyraldehyde over wide ranges in the state parameters

Dynamic-viscosity measurements are reported for liquid mixtures in the system formed by n-butyraldehyde and isobutyraldehyde.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 48, No. 2, pp. 321–322, February, 1985.     

Pesticide monitoring programme of the Ministry of Health of Brazil

The structure of the recently introduced Brazilian government programme for monitoring pesticide residues in six major agricultural products is described. Residues found from the analysis of samples of tomatoes and strawberries are discussed in detail. The much greater frequency of detection of pesticide residues, many of which are not approved for use in Brazil, in produce being sold on the domestic market, as opposed to that produced for export, is of major concern. It is perceived that this new monitoring programme will become permanent and be used to underpin enforcement actions that will need to be taken to reduce the numbers of incidents of illegal residues occurring, particularly in fresh fruits and vegetables.     

Production of maraging steel grades and the influence of specified and nonspecified elements for special applications

The material properties of maraging steels are greatly affected by the alloy and inclusion content and hence by the production route. This paper describes various past and current production routes at Böhler Edelstahl GmbH and the effect of these routes on the specified element (alloy) and non-specified element (inclusion) contents. Non-metallic inclusions were investigated by EDX analysis. The effects of various alloying and tramp elements on the material properties are presented as a statistical evaluation of previous melts. Nitrogen solubility was calculated with Thermo–Calc for maraging steel Mat.-No. 1.6354 and the precipitation of nitrides is discussed. A proposal is made for the production of melts with improved properties.