A randomized voltage vector switching scheme for three-level powerinverters

In this paper, a feasibility study of a randomized space vector switching scheme for three-level inverters is reported. Based on the traditional space vector concept for pulse width modulation (PWM) inverters, the sequence of the space vector is randomized in this scheme. The overall vector, resulting from the randomization, is mathematically identical to that of the traditional space vector. It has been found that the randomized scheme can effectively spread the switching noise over a wide frequency range and at the same time keep the steady-state link capacitor voltage balanced. The proposed scheme has been implemented in real time in a digital controller and its features have been experimentally confirmed     

Design and performance of expanded mode fiber using microoptics

In order to relax alignment tolerances on single-mode fiber interconnection, we propose an end face treatment to realize an expanded mode fiber. This new technique consists of splicing fibers with various lengths and characteristics. The spot size and coupling properties are analyzed numerically considering the effects of gap, offset, and tilt. Low loss, wide misalignment tolerances, and low cost are achieved. The fabrication process and experiment results are presented. The performance of a connector with this expanded fiber is reported.     

Adjuvant arthritis: influence of the adjuvant volume and composition on the non-specific inflammation

Adjuvant-induced arthritis is an animal model of chronic inflammatory disease widely used in anti-inflammatory and immunosuppressive drugs testing. When the development and the inhibition of the induced arthritis are measured by the injected paw oedema, it is difficult to delineate the immunological contribution from the persistent non-specific primary section. To study the influence of volume and composition of the injected adjuvant upon the primary non-specific inflammation, we devised a 3X4 factorial experiment on a strain of inbred rats with a low susceptibility to adjuvant-induced arthritis. The injection of mineral oil alone produces a persistent oedema. The injection of mycobacteriae in suspension in saline induces a rapid inflammatory response followed by a fast decrease of the oedema. When complete adjuvant is used, there is always a very strong interaction between the effects of the two components of the adjuvant, i.e. the measured oedemas are much greater than the calculated values, For a given injected volume, the inflammation is maximum when the concentration of mycobacteriae is 2.5 mg/ml. All the rats injected with complete adjuvant present a transient oedema of the non-injected hind paw. This oedema is very small and proportional to the amount of mycobacteria injected.     

Deposition mechanisms in langmuir-blodgett films

As part of a study of the possible application of polymerisable Langmuir-Blodgett (LB) films as ultra-fine-line e-beam resists, an investigation of the variation of film structure of 22-tricosenoic acid with differing deposition conditions has been made. Unexpected effects with significant implications for deposition speed and resist sensitivity have been observed, and the new techniques for film characterisation developed during the investigation have resulted in a revised model of deposition explaining the observed independence of the disorder causing optical scattering and the macroscopic features observed by polarised microscopy.     

Refractive index profiling-state of the art

Problems associated with different calibration techniques and some instrumental effects that can determine instrumental accuracy are discussed. It is shown how transmission effects can be observed and used to generate a correction curve for refracted near-field instruments. High-quality fiber slices needed for axial interferometry were used to obtain refractive index differences on suitable fibers to ±1% with the measurements traceable to national standards. Interferometry was used to calibrate a multiple-step fiber which is available in 10-m lengths with a certificate of calibration. The limitations of the technique are discussed, and preliminary results of a study on the effects of residual stress and stress relief on measurements are given. Comparisons are made between measurements made by axial interferometry and refracted near field on a range of fibers. It is shown that commercial profilers can produce reliable measurements of refractive index difference, absolute refractive index, profile shape, and numerical aperture that agree well with measurements by other techniques     

The effect of additives on the thermal stability of poly(vinyl chloride)

The effect of a range of organic additives on the thermal stability of poly(vinyl chloride), both with and without a chloroparaffin extender, was studied using a number of experimental techniques. Of the additives used the best overall balance was provided by pentaerythritol, which increased stability when the extender was present and had no effect when it was absent. The congo red test emerged as the most suitable technique, being consistent and inexpensive and able to screen several additives simultaneously. Isothermal differential thermal analysis correlated with the congo red test but required more expensive equipment, was time-consuming and demanded good mixing of the poly(vinyl chloride) compound to give reproducible results. Thermogravimetry was not sufficiently sensitive and the heat stability test was the least useful of all.