High extinction-ratio microstructure fiber based on chalcogenide glasses

Extinction ratio (ER) is one of the important parameters to characterize the polarization-maintaining (PM) performance of the fiber. In this paper, we report the preparation and properties of a novel chalcogenide microstructure fiber with a high ER. We fabricate a preform using a peeled-off extrusion method. The core and cladding material of the fiber are Ge₉As₂₃Se₆₈ and Ge₁₀As₂₂Se₆₈. The preform was drawn into a fiber with an average ER of −17.08 dB. The loss of the fiber is less than 2 dB over 5.20–8.55 μm, and the minimum loss of the fiber is 0.57 dB/m at 6.2 μm. Moreover, a flat mid-infrared supercontinuum spectrum spanning from 1.53 to 12.50 μm is generated by pumping an 18-cm-long PM fiber for the first time.     

Polyethylenimine-modified sugarcane bagasse cellulose as an effective adsorbent for removing Cu(II) from aqueous solution

Polyethylenimine-modified sugarcane bagasse cellulose (SBCMP), as a new adsorbent, was synthesized by the reaction of polyethylenimine (PEI) with sugarcane bagasse cellulose and glutaraldehyde. The adsorption of Cu(II) by SBCMP was pH-dependent, and the higher removal efficiency of Cu(II) appeared in the range of pH 3.0–6.0. The adsorption isothermal data fitted well with the Langmuir model, and the maximum adsorption capacity of SBCMP was up to 107.5 mg/g. The adsorption kinetics was best described by the pseudo-second-order kinetic. The adsorption of Cu(II) by SBCMP was unfavorable at high temperatures, and thermodynamic analyses implied that the adsorption of Cu(II) by SBCMP was an exothermic reaction. Fourier transform infrared spectroscopy (FT-IR) combined with X-ray photoelectron spectroscopy (XPS) revealed that Cu(II) adsorption on SBCMP mainly controlled by the nitrogen atoms of  NH group in PEI. The results of regeneration cycles showed that SBCMP was suitable for reuse in the adsorption of Cu(II) from aqueous solution. These experimental results suggested that SBCMP is expected to be a new biomass adsorbent with high efficiency in removing Cu(II) from wastewater.     

Performance of biomimetic coating modified fiber incorporated styrene butadiene styrene modified asphalt

This study reports the effect of polydopamine bionic coating and γ-methacryloxypropyltrimethoxysilane (KH570) composite modified polyacrylonitrile (PAN) fiber as a secondary modifier on the performance of styrene-butadiene-styrene (SBS) modified asphalt. Dynamic shear rheometer test indicated the complex shear modulu, storage modulus, and loss modulus of modified PAN (KD-PAN) incorporated SBS modified asphalt was increased by 12.4, 20.5, and 11.2%, respectively compared with PAN/SBS modified asphalt. The master curve of G^* of fiber/SBS composite modified asphalt shows that the deformation resistance of KD-PAN/SBS modified asphalt is greater than that of PAN/SBS modified asphalt in the entire loading frequency range. The cone penetration test showed significantly enhanced shear strength of KD-PAN/SBS modified asphalt. The adhesion work test results and SEM images of interface between fiber and SBS modified asphalt revealed that the adhesion effect of KD-PAN and SBS modified asphalt is better than that of PAN and SBS modified asphalt. SEM and AFM images of fiber further showed that the fiber surface becomes rough after modification. The increased surface roughness of KD-PAN facilitated the adherence of SBS modified asphalt to it, which in turn led to the enhanced performance of KD-PAN/SBS composite modified asphalt at the same fiber content and temperature.     

Study on performance characteristics of fused deposition modeling 3D-printed composites by blending and lamination

Component contacting degree in a composite material is an important reference for evaluation the performance characteristics. In this article, two composite material systems involving polylactic acid (PLA) with acrylonitrile butadiene styrene (ABS) and PLA with thermoplastic polyurethane (TPU) were prepared by blending and laminating through fused deposition modeling (FDM) 3D printing technology. The mechanical and thermal properties of the as-prepared composite materials were examined. The results indicated that PLA and TPU played a dominant role in tensile strength and breaking elongation, respectively, in individual composite material. ABS and TPU changed the glass transition peek, crystallinity, and modulus of PLA. The results also suggested that although the processing design of the blending method was more suitable for the contact between two components, but the mechanical properties of laminated composites were closer to theoretical predictions. The structural design and processing technology provide a comparative method and reference basis for studying the performance characteristics of composite materials.     

Engineering all-aromatic polyamide surface from hydrophilic to superhydrophobic and the accelerated strategy

Being a new kind of nanomaterials, aromatic polyamide nanofibers (ANF) have been much highlighted in recent studies. We here demonstrate an isopropyl alcohol (IPA) accelerated chemical cleavage on poly (p-phenylene terephthalamide) chopped fibers, which provides an efficient preparation method of ANF. The comprehensive study on the processes accelerated by different alcohols revealed that the preparation time of ANF in the mixed medium of dimethyl sulfoxide (DMSO)-alcohol (20:1 in volume) was shorten to 45 min and 75 min for methanol (ethanol) and isopropanol, respectively. However, the nanofibers prepared in DMSO-IPA exhibited the minimum in axial and radial dimensions, providing the finest and most uniform diameter of 16 nm. The corresponding ANF films through vacuum assisted filtration also showed the highest tensile strength of 150 MPa, in comparison with those of the ANF films prepared using other alcohols, which were about 110 MPa. Furthermore, ANF/silicon hybrid films were prepared by the ionic ring-opening reaction followed by the alkoxysilane condensation and nanoparticle fabrication. By changing the organo functional groups in the alkoxysilane, the surface of the films were adjustable in a wide contact angle range from 56° (hydrophilic) to 150° (superhydrophobic), suggesting the amendable interfacial properties potential applicable to composite fabrication with most of the resin matrix.     

A Cross-sectional Study on the Relationship Between Homocysteine and Lipid Profiles Among Chinese Population from Hunan

Previous studies have explored the relationship between homocystein (Hcy) and lipid profiles. However, the results from these studies have been inconsistent. The current study investigated the correlation between Hcy and lipid profiles in Chinese community-based population. The participants were composed of 4012 Chinese people aged 30–92 years old, who were recruited from rural and urban communities in the Hunan Province. Non-parametric test and logistic regression were used to examine the distribution of Hcy and lipid profiles (triglyceride [TG], total cholesterol [TC], low-density lipoprotein cholesterol [LDL-C], high-density lipoprotein cholesterol [HDL-C]) and the relationship between them. The median age of subjects was 54.50 years old, and 40.98% were male. Median Hcy was 13.20 μmol/L, and 35.39% had hyperhomocysteinemia (HHcy). Median TG was 1.51 mmol/L, TC was 4.77 mmol/L, LDL-C was 2.62 mmol/L, and HDL-C was 1.27 mmol/L. In multivariable logistic regression analysis, HHcy was associated with high levels of TG (OR_male = 2.240, p < 0.001; OR_female = 2.539, p < 0.001), TC (OR_male = 2.237, p < 0.001; OR_female = 2.202, p < 0.001), and LDL-C (OR_male = 1.413, p = 0.010; OR_female = 1.617, p < 0.001) in the different sexes population and low level of HDL-C in females (OR = 1.326, p = 0.023) after adjusting for confounders. HHcy was independently associated with an increasing risk of low HDL-C among females. The regression analysis showed that HHcy was also associated with hypertriglyceridemia, hypercholesterolemia, and high level of LDL-C in males and females from Chinese community-based population, which provides a basis for the treatment and prevention of abnormal lipid metabolism.     

Viscoelastic properties and flow instabilities of aqueous suspensions of cellulosic fibers: Effects of a gelation agent on dispersion,rheology, and flow stability

Processing of concentrated lignocellulosic biomass suspensions typically involves the conversion of the cellulose into sugars and sugars into ethanol. Biomass is usually pretreated via methods like comminution or steam explosion to form fine cellulosic fibers to be dispersed into an aqueous phase for further treatment. The resulting cellulose suspensions need to be pressurized and pumped into and out of various processing vessels without allowing the development of flow instabilities that are typically associated with “demixing”, that is, the segregation of the cellulosic biomass from the aqueous phase via the formation of mats of cellulosic fibers and the filtration of the aqueous phase. Such demixing can prevent continuous processing at high rates. Here, the development of flow instabilities via the demixing effect for cellulose suspensions is demonstrated using capillary and compressive squeeze flows. It is shown that the use of a gelation agent, hydroxypropyl guar gum, at the critical concentration of 0.5 wt% or higher significantly affects the viscoelastic material functions of cellulosic suspensions, improves the dispersive mixing of the fibers within the aqueous phase, and results in the elimination of the flow instabilities and associated demixing effects that are ubiquitously observed during the pressurization and processing of cellulosic suspensions.     

Systematic investigation on the effect of crosslinking agent type and dosage on the performance of TPU/MVQ based thermoplastic vulcanizates

Dynamic vulcanized thermoplastic polyurethane (TPU)/methyl vinyl silicone rubber (MVQ) thermoplastic vulcanizates (TPVs) were prepared in torque rheometer. The influence of the type and amount of peroxide crosslinking agent on the mechanical properties, thermal stability, micromorphology and melt flowability was systematically investigated. The results showed that the mechanical properties of the TPVs vulcanized by 2,5-dimethyl-2,5-di (tert-butyl peroxy) hexane (DBPH) first increased and then decreased with increasing the peroxide amount, while for dicumyl peroxide (DCP) vulcanizing system the mechanical properties slowly increased. Besides, the comprehensive mechanical properties vulcanized by DBPH were better than those of DCP group. The results of the thermogravimetric analysis showed that the TPVs vulcanized by DBPH had better heat stability, corresponding to the excellent thermo-oxidative aging performance and the 38% increase in tensile strength after aging. In addition, the MVQ rubber particles showed better dispersing performance for DBPH vulcanizing system. The melt flow rate of the TPVs showed a linear relationship with increasing DBPH dosage and became worse after the amount of crosslinking agent exceeded 1.5 phr. By comprehensive comparison, the TPVs have better performance when use peroxide DBPH as the crosslinking agent and the dosage is 1.5 phr.     

Enhanced wear resistance of ultra-high molecular weight polyethylene fibers by modified-graphite oxide

A simple and feasible method to enhance the wear resistance of ultra-high molecular weight polyethylene (UHMWPE) fibers was reported. The graphite oxide (GO) prepared using improved Hummer's method was surface modified with hexadecylamine to improve its compatibility with UHMWPE. Combined with well-dispersion of modified-GO (m-GO) in dichloromethane and the fact that the viscosity of UHMWPE suspension can be decreased by dichloromethane, the well dispersed m-GO/dichloromethane was added into UHMWPE suspension to improve m-GO dispersion in UHMWPE fibers. Finally, UHMWPE fibers with different m-GO concentration were prepared using gel spinning technology. The effect of m-GO concentration on the structure and properties of modified UHMWPE fibers were investigated. The results indicated that the melting temperature and crystallinity of m-GO modified UHMWPE fibers increased with increasing of m-GO concentration, while the fiber's crystal sizes and orientation increased, thus the tensile strength of m-GO modified UHMWPE fibers remained almost undamaged. The introduction of m-GO is beneficial to the formation of smooth transfer film on fiber's surface, which enhanced the self-lubrication of UHMWPE fibers. Compared with pure UHMWPE fiber, the UHMWPE fiber containing 1.5 wt% m-GO had enhanced wear resistance by 55.4% and still maintained high tensile strength of 29.98 cN dtex⁻¹.     

西北省间实时平衡电力市场探索

新能源出力的波动性和随机性影响电网实时平衡.中国西北电网新能源占比高、平衡资源时空分布不均衡,分省市场实时平衡困难,为此,文中设计西北省间实时平衡电力市场,以发挥西北省间实时平衡能力,适应高比例新能源电网实时平衡需要.首先,结合国内外电力市场建设与西北实时平衡现状,分析了建立西北省间实时平衡市场的必要性;然后,说明了双边竞价的市场运作思路,提出了基于潮流的市场耦合方法的市场竞价出清模型,设计了市场运作流程;最后,讨论了西北省间实时平衡市场与其他市场之间的协调运作,通过模拟算例说明了西北省间实时平衡市场的作用.