Measurements of thick target fission yields as a probe of fission excitation functions for deep sub-barrier energies

A close-geometry experimental technique has been developed and used to measure thick target fission yields for protons on ²³⁸U from 4.2 to 12 MeV. Fission fragments were detected at back angles by an annular photo-voltaic detector in coincidence with γ-ray registered in large NaI(Tl) detector. The neutron induced fission background was monitored by a detector on the downstream side of the thick target. Measured yields compare well with those calculated from published thin target cross sections. This method has the required sensitivity to carry out measurements at still lower energies where recent measurements give conflicting findings.     

Electromagnetic coupling effects on the cavity measurement of antenna efficiency

Electromagnetic coupling effects on the antenna in a conducting cavity are studied theoretically and experimentally. It is observed in experiments that at the resonant frequencies of the cavity, the input resistance of the antenna attains values two or three orders of magnitude higher than that at frequencies away from resonance. It is shown via theoretical analysis that the input resistance of the antenna measured at the resonant frequencies of the cavity is not merely the loss resistance desired in computing the antenna efficiency, but is actually the sum of the loss resistance of the antenna and the coupling resistance between the antenna and cavity. This coupling effect is demonstrated quantitatively by numerical computations for dipole and monopole antennas. The computational results for the input resistance are in agreement with the measured data. A method is proposed to avoid the cavity-antenna antiresonance in the measurement.     

Athermalised monolithic VMUX employing silica arrayed waveguide grating multiplexer

The realisation of a monolithic athermalised variable-optical-attenuator-integrated multiplexer (VMUX) implemented in silica-on-silicon waveguide technology is reported. The VMUX incorporates an athermal arrayed waveguide grating, providing <0.05 nm of peak transmission wavelength shift over 20-70/spl deg/C operating ambient independent of attenuator settings.     

Evaluation of the recombinant 38-kilodalton antigen of Mycobacterium tuberculosis as a potential immunodiagnostic reagent

The diagnosis of infection caused by Mycobacterium tuberculosis is of increased public health concern following increases in the number of cases in developed countries and major increases in developing countries associated with the spread of human immunodeficiency virus (HIV) infection. The specificity of purified protein derivative skin testing for the detection of infection is compromised by exposure to environmental mycobacteria. Examination of sputum detects the most infectious patients, but not those with extrapulmonary disease. The 38-kDa antigen of M. tuberculosis contains two M. tuberculosis-specific B-cell epitopes. We overexpressed the gene for this antigen in Escherichia coli and evaluated the recombinant product in in vitro assays of T-cell function and as a target for the antibody response in humans. The sensitivity and specificity of the antigen as a skin test reagent were also assessed in outbred guinea pigs. We found that 69% of healthy sensitized humans recognize the antigen in vitro, as manifested by both cell proliferation and the production of gamma interferon. Untreated patients initially have a lower frequency of response (38%); this recovers to 72% during therapy. A total of 292 patients (20 with HIV coinfection) and 58 controls were examined for production of antibody to the 38-kDa antigen by using a commercially available kit. The sensitivity of the test in comparison with that of culture was 72.6%, and the specificity was 94.9%. The antigen was also tested for its ability to induce skin reactions in outbred guinea pigs sensitized by various mycobacterial species. The antigen provoked significant skin reactions in M. tuberculosis-, M. bovis BCG-, and M. intracellulare-sensitized animals. The significance of these findings and the usefulness of this antigen in immunodiagnosis are discussed.     

Moisture influence on fungal growth in black pepper

The moisture content at which fungal growth proliferated on black pepper was determined at different relative humidities. At 18% moisture content, fungal growth occurred but this was not recorded at the next lower moisture content of 13.9%. Microscopic examination of infected fresh green pepper showed the presence of species of Trichothecium, Colletotrichum and Fusarium. In black pepper, species of Aspergilli and Penicillium were observed.     

The growth of roughness during electrodeposition

Measurements of the growth rate of roughness on a cathode surface can be used to study the physics of cathodic processes. But these growth rates are cell wide variables and they ordinarily depend on what is taking place at the anode as well as at the cathode. Our aim is to derive a simple condition under which the anode makes no contribution to the interpretation of growth rate measurements at the cathode.Our condition stems from the contribution of ion diffusion to the growth rate and it is satisfied for all non-small values of the wave number of a growing disturbance. This, together with the fact that surface tension is the only stabilizing factor and the fact that the surface tension coefficient multiplying the wave number is small, means that the anode ought not to be important for the fastest growing wave numbers.Once the effect of the anode is eliminated, the growth rate at the cathode can be expressed in a formula so simple that pencil and paper calculations are possible and this makes important questions in cell design easy to answer, e.g., is the growth rate diffusion controlled?     

CRITICAL POINTS IN THE SOLIDIFICATION OF A PURE MATERIAL

Patterns in the solidification of a pure material are dealt with in this article. Results, deduced from a simple model based on heat conduction in the two phases and the effect of surface tension on the equilibrium temperature at the moving front, present a guide for experimental work. By introducing far-field conditions imitating what can be achieved in an experiment, we explain how the depths of the phases and the width of the container influence the patterns that can be seen if one advances the control variable to the critical point and then just beyond. Our new result is the existence of a third critical point. It occurs at small wave numbers and it is independent of surface tension. It appears because we take the depths of the phases into account. These depths are input values that offer the possibility of controlling crest-to-trough conduction, stabilizing in the solid, destabilizing in the liquid. The new critical point, and the patterns attending its appearance, can be found in cells of easily attainable widths.     

Virtualized Reality: Perspectives on 4D Digitization of Dynamic Events

Digitally recording dynamic events, such as sporting events, for experiencing in a spatio-temporally distant and arbitrary setting requires 4D capture: three dimensions for their geometry and appearance over the fourth dimension of time. Today's computer vision techniques make 4D capture possible. The virtualized reality system serves as an example on the general problem of digitizing dynamic events. In this article, we present the virtualized reality system's details from a historical perspective     

Research in object-oriented manufacturing simulations:an assessment of the state of the art

Object-oriented programming (OOP) has been revolutionizing software development and maintenance. When applied to simulation of manufacturing systems, OOP also provides an opportunity for developing new ways of thinking and modeling. In this paper, we identify existing large-scale, persistent OOP-based research efforts focusing on manufacturing system simulation, and present an integrating framework for discussing the associated modeling abstractions, implementation strategies, common themes, and distinctive features. The goal is to identify the fundamental research and application issues, assess the current state of the art, and identify key research needs.     

Mixed Micelles of Surface Active Ionic Liquid (SAIL)–Octylphenol Ethoxylate: A Novel Reaction Medium for Selective Oxidation of Toluene to Benzaldehyde

Ionic liquids have been found to be suitable alternatives to volatile organic solvents in chemical transformation. Through a proper choice of cations and anions, the properties of an ionic liquid can be tuned so that it resembles an amphiphile. Such specially designed molecules are known as surface-active ionic liquids (SAIL). Like conventional surfactants, SAIL also form aggregates in an aqueous medium. Studies show that the mixing of SAIL with conventional surfactants leads to synergistic micellization. However, very few reports are available on the application of such systems as reaction media. Present study focuses on the application of mixed micelles of 1-tetradecyl-3-methylimidazol-1-ium bromide, ([C₁₄mim]Br) with nonionic surfactant, Octylphenol ethoxylate with 10 moles of ethylene oxide (OPE-10). Enhanced solubilization and selective catalytic oxidation of toluene using hydrogen peroxide as an oxidant and tungstic acid as a catalyst have been studied in detail using this system.