Electrochemical Impedance Spectroscopic Analysis of Sensitization-Based Solar Cells

Electrochemical impedance spectroscopy (EIS) is a very powerful tool for elucidation of charge transfer and transport processes in sensitization-based solar cells (e.g., dye-sensitized solar cells [DSSCs], quantum dot-sensitized solar cells [QDSSCs], and perovskite solar cells [PSCs]). EIS measures the electrochemical response to small amplitude AC signals over a wide range of frequencies. Analysis of the EIS response provides information about the corresponding parameters of the cells. Here, we review the fundamentals of EIS, charge transport kinetic processes, and equivalent circuit models of sensitization-based solar cells and use these concepts to explain the EIS spectra of DSSCs, QDSSCs, and PSCs. This review will be very useful for understanding the fundamental charge transfer and transport processes in different sensitization-based solar cells and the use of an equivalent circuit model to interpret the observed charge transfer and reactions.     

Magnetic Nanoparticle Arrays Self-Assembled on Perpendicular Magnetic Recording Media

We study magnetic-field directed self-assembly of magnetic nanoparticles onto templates recorded on perpendicular magnetic recording media, and quantify feature width and height as a function of assembly time. Feature widths are determined from Scanning Electron Microscope (SEM) images, while heights are obtained with Atomic Force Microscopy (AFM). For short assembly times, widths were ~150 nm, while heights were ~14 nm, a single nanoparticle on average with a 10:1 aspect ratio. For long assembly times, widths approach 550 nm, while the average height grows to 3 nanoparticles, ~35 nm; a 16:1 aspect ratio. We perform magnetometry on these self-assembled structures and observe the slope of the magnetic moment vs. field curve increases with time. This increase suggests magnetic nanoparticle interactions evolve from nanoparticle–nanoparticle interactions to cluster–cluster interactions as opposed to feature–feature interactions. We suggest the aspect ratio increase occurs because the magnetic field gradients are strongest near the transitions between recorded regions in perpendicular media. If these gradients can be optimized for assembly, strong potential exists for using perpendicular recording templates to assemble complex heterogeneous materials.     

Alcoholysis of palm oil mid-fraction by lipase from Rhizopus rhizopodiformis

A mycelial lipase from Rhizopus rhizopodiformis was prepared in fragment form. The lipase was examined to catalyze the alcoholysis of palm oil mid-fraction (PMF) in organic solvents. High percentage conversions of PMF to alkyl esters were achieved when methanol or propanol was used as acyl acceptor. Of the two most prevalent fatty acids in PMF, palmitic acid seemed to be preferred over oleic acid in the formation of methyl and propyl esters. The optimal ratio of oil to methanol in the alcoholysis reaction is 1 to 2 moles. The lipase exhibited high alcoholysis activities in nonpolar solvents (log P>2), such as hexane, benzene, toluene, and heptane. The enzyme showed exceptionally high thermostability.     

Effects of functionalization conditions of sulfonic acid grafted SBA-15 on catalytic activity in the esterification of glycerol to monoglyceride: a factorial design approach

A series of propyl sulfonic acid-modified SBA-15 catalysts (SBA-15SO₃H) was prepared under various conditions using post-functionalization approach. A factorial design coupled with response surface analysis were employed to evaluate the effects of the preparation conditions on the catalyst activity. Optimization of the conditions to find the most active SBA-15SO₃H catalyst with the highest activity in glycerol esterification with lauric acid at 160?°C for 6?h was also made. Amount of 3-(mercaptopropyl)trimethoxysilane (MPTMS) and reflux time were chosen as parameters of the preparation conditions. The presence of propyl sulfonic acid groups in SBA-15SO₃H catalysts was confirmed by FT-TIR method. The catalysts were also characterized by means of surface analysis, XRD, TEM and TGA. The results obtained from the statistical models suggested that the amount of MPTMS was more important parameter to influence the activity compared to the reflux time. The optimum preparation condition was achieved at a reflux time of 20?h and an MPTMS amount of 1?mL/gram SBA-15 to obtain the SBA-15SO₃H(1) with the highest monoglyceride selectivity (70.2%) and corresponding lauric acid conversion (95%) in the esterification process.     

Mass transfer from outer surface of thin tubes in parallel turbulent flow

The mass transfer coefficients from the outer surface of tubes or cylinders held in parallel turbulent steams have been calculated using integral momentum and mass transfer equations. The solution uses a hydrodynamics independent constant, λ _c which depends only upon Schmidt number. The results exhibit significant effect of curvature. For Schmidt number less than 108, Sherwood number can be predicted by $Sh_d Sc^{ - 1/3} = 0.039Sc^{0.208} times left( {frac{L} {d}} right)^alpha operatorname{Re} _d^{0.8}$Sh_d Sc^{ - 1/3} = 0.039Sc^{0.208} times left( {frac{L} {d}} right)^alpha operatorname{Re} _d^{0.8}, where α = −0.169Sc^−0.0103. The effect of the curvature is insignificant where $frac{L} {d}operatorname{Re} _L^{ - 0.2} - 0.033 times ln (Sc) leqslant 0.214$frac{L} {d}operatorname{Re} _L^{ - 0.2} - 0.033 times ln (Sc) leqslant 0.214.     

Thermal conductivity prediction of foods by Neural Network and Fuzzy (ANFIS) modeling techniques

A neuro-fuzzy modeling technique was used to predict the effective of thermal conductivity of various fruits and vegetables. A total of 676 data point was used to develop the neuro-fuzzy model considering the inputs as the fraction of water content, temperature and apparent porosity of food materials. The complexity of the data set which incorporates wide ranges of temperature (including those below freezing points) made it difficult for the data to be predicted by normal analytical and conventional models. However the adaptive neuro-fuzzy model (ANFIS) was able to predict conductivity values which closely matched the experimental values by providing lowest mean square error compared to multivariable regression and conventional artificial neural network (ANN) models. This method also alleviates the problem of determining the hidden structure of the neural network layer by trial and error.     

Viscoelastic and thermal properties of natural rubber low-density polyethylene composites with boric acid and borax

The influence of boric acid (BA) and borax (BO) neutron-absorbing fillers on thermal stability and viscoelastic behavior of natural rubber (NR) low-density polyethylene composites has been studied. The thermal degradation and dynamic mechanical properties of the composites have been analyzed as a function of temperature. The results revealed the enhancement of thermal stability of the composites by the addition of BA and BO fillers. The flame resistance of the material was improved by the addition of both the fillers. The storage modulus was found to be dependent upon the temperature and nature of the filler. The amount of NR chains immobilized by filler particles has been quantified from dynamic mechanical analysis and secondary filler/filler interactions have been verified by the Payne effect analysis. Finally, the experimental results have been compared with theoretical predictions.     

Structure and thermal properties of La0.6Sr0.4Co0.2Fe0.8O3−δ-SDC carbonate composite cathodes for intermediate- to low-temperature solid oxide fuel cells

The structure and thermal properties of La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ-SDC carbonate (LSCF-SDC carbonate) composite cathodes were investigated with respect to the calcination temperatures and the weight content of the samarium-doped ceria (SDC) carbonate electrolyte. The composite cathode powder has been prepared from La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ and SDC carbonate powders using the high-energy ball milling technique in air at room temperature. Different powder mixtures at 30 wt%, 40 wt% and 50 wt% of SDC carbonate were calcined at 750-900 °C. The findings indicated that the structure and thermal properties of the composite cathodes were responsive to the calcination temperature and the content of SDC carbonate. The absence of any new phases as confirmed via XRD analysis demonstrated the excellent compatibility between the cathode and electrolyte materials. The particle size of the composite cathode powder was ∼0.3-0.9 μm having a surface area of 4-15 m² g⁻¹. SEM investigation revealed the presence of large particles in the resultant powders resulting from the increased calcination temperature. The composite cathode containing 50 wt% SDC carbonate was found to exhibit the best thermal expansion compatibility with the electrolyte.     

Enhancement of mechanical and thermal properties of polycaprolactone/chitosan blend by calcium carbonate nanoparticles

This study investigates the effects of calcium carbonate (CaCO(3)) nanoparticles on the mechanical and thermal properties and surface morphology of polycaprolactone (PCL)/chitosan nanocomposites. The nanocomposites of PCL/chitosan/CaCO(3) were prepared using a melt blending technique. Transmission electron microscopy (TEM) results indicate the average size of nanoparticles to be approximately 62 nm. Tensile measurement results show an increase in the tensile modulus with CaCO(3) nanoparticle loading. Tensile strength and elongation at break show gradual improvement with the addition of up to 1 wt% of nano-sized CaCO(3). Decreasing performance of these properties is observed for loading of more than 1 wt% of nano-sized CaCO(3). The thermal stability was best enhanced at 1 wt% of CaCO(3) nanoparticle loading. The fractured surface morphology of the PCL/chitosan blend becomes more stretched and homogeneous in PCL/chitosan/CaCO(3) nanocomposite. TEM micrograph displays good dispersion of CaCO(3) at lower nanoparticle loading within the matrix.     

Role of sand on curing of partex surface by UV radiation

A partex surface was modified by a UV‐curing system with epoxy acrylate (EB‐600). A set of formulations was prepared with oligomer and the trifunctional monomer trimethylol propane triacrylate in different combinations of percentages (1–5%) of sand to study the role of sand in various physical properties of UV‐cured thin films, as well as partex surfaces. Increased pendulum hardness (PH), gloss, adhesion, and abrasion values were obtained by the addition of sand into the partex surfaces. The best results were obtained with the formulation containing 3% sand. An enhanced PH and a decreased percentage of gel content of the UV‐cured film was observed with an increase of the sand concentration. A simulated weathering test was performed with partex surfaces cured by a formulation containing 3% sand in the base coat. The losses of the physical properties were found to be lower over the surface treated with the formulation containing sand. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2385–2392, 2002