Emission factors for gas-powered vehicles traveling through road tunnels in São Paulo, Brazil

The objective of this study was to improve the vehicular emissions inventory for the light- and heavy-duty fleet in the metropolitan area of S?o Paulo (MASP), Brazil. To that end, we measured vehicle emissions in road tunnels located in the MASP. On March 22-26, 2004 and May 04-07, 2004, respectively, CO, CO2, NOx, SO2, and volatile organic compounds (VOCs) emissions were measured in two tunnels: the Janio Quadros, which carries light-dutyvehicles; and the Maria Maluf, which carries light-duty vehicles and heavy-duty diesel trucks. Pollutant concentrations were measured inside the tunnels, and background pollutant concentrations were measured outside of the tunnels. The mean CO and NOx emission factors (in g km(-1)) were, respectively, 14.6 +/- 2.3 and 1.6 +/- 0.3 for light-duty vehicles, compared with 20.6 +/- 4.7 and 22.3 +/- 9.8 for heavy-duty vehicles. The total VOCs emission factor for the Maria Maluf tunnel was 1.4 +/- 1.3 g km(-1). The main VOCs classes identified were aromatic, alkane, and aldehyde compounds. For the heavy-duty fleet, NOx emission factors were approximately 14 times higher than those found for the light-duty fleet. This was attributed to the high levels of NOx emissions from diesel vehicles.     

Simultaneous HPLC quantification of total cholesterol,tocopherols and β-carotene in Barrosã-PDO veal

A simple, rapid and sensitive procedure for the simultaneous determination of total cholesterol, tocopherols and β-carotene in meat is described. The method involves a direct saponification of the meat, a single n-hexane extraction and the analysis of the extracted compounds by normal-phase HPLC, using fluorescence (tocopherols) and UV–Vis photodiode array (cholesterol and β-carotene) detections in tandem. Rates of recovery of spiked meat samples were 93% for cholesterol, 83–86% for (α-, β- and -γ) tocopherols and 89% for β-carotene. Repeatabilities were high (CV < 6%) for all determined compounds, except for δ-tocopherol. This tocopherol, which is not usually present in meat, showed a much lower recovery percentage (73%) and repeatability (12.8%). This methodology was applied for the quantification of total cholesterol, tocopherols and β-carotene in three muscles (longissimus thoracis, longissimus lumborum and semitendinosus) of the Portuguese traditional Barrosã-PDO veal, obtained from autochthonous calves fed extensively during summer (with the least abundant green pastures) and slaughtered in early autumn (October). Barrosã-PDO veal showed median contents of total cholesterol (0.50–0.56 mg/g) and, depending on the analysed muscle, moderate to high contents of α-tocopherol (3.3–3.9 μg/g) and β-carotene (0.07–0.09 μg/g), suggesting an high sensorial and hygienic quality.     

Control of Microbial Adhesion as a Strategy for Food and Bioprocess Technology

Bacteria and other microorganisms have a natural tendency to adhere to surfaces as a survival mechanism. This can occur in many environments, including the living host, industrial systems, and natural waters. The general outcome of bacterial colonization of a surface is biofilm formation, which consists of microorganisms immobilized in a variety of polymeric compounds generally referred to as extracellular polymeric substances. Bacterial adhesion to a solid surface is a crucial step in the biofilm process. This step is dependent upon van der Waals, electrostatic, and acid–base interactions. These interactions are influenced by physicochemical properties of the substratum and the bacterial surface, such as hydrophobicity, surface charge, and electron donor–electron acceptor properties. In addition, the roughness of the substratum and the microbiological characteristics of the cell surface, such as cellular appendages and production of exopolysaccharides, can affect the adherence process. To date, many strategies have been developed to decrease the adherence of bacteria to surfaces. Surface modification with the addition of the suitable compounds makes surfaces less attractive for microorganisms and therefore prevents bacterial adherence and biofilm formation.     

Effect of active packaging incorporated with triclosan on bacteria adhesion

ABSTRACT: Antimicrobial polyethylene and cellulose based films incorporated with triclosan were studied. The antimicrobial efficacy, the hydrophobicity, microscopic and the mechanical characteristics of the films, as well free energy of adhesion between bacteria and antimicrobial films were evaluated. It was observed that both polyethylene and cellulose based films incorporated with the antimicrobial were homogeneous. Furthermore, the addition of triclosan did not affect mechanical characteristics of the films (P > 0.05). However, triclosan incorporated into polyethylene films reduced its hydrophobicity while antimicrobial cellulose based films became more hydrophobic. The adhesion was thermodynamically favorable between tested bacteria and polyethylene films. On the other hand, the adhesion to triclosan cellulose based film was thermodynamically unfavorable to Staphylococcus aureus and Escherichia coli and favorable to Listeria innocua and Pseudomonas aeruginosa. Polyethylene and cellulose based films showed inhibitory effect against S. aureus and E. coli, being the inhibition halo higher for polyethylene films. This study improves the knowledge about antimicrobial films.     

Modelling the effect of strain rate on the thermomechanical behaviour of AISI 304 stainless steel

The present work deals with the interdependences between the strain rate and the strain hardening on stainless austenitic steels. Uniaxial tension tests were conducted on a 304 stainless steel at different strain rates in order to analyse the influence of this parameter on the strain hardening and on the material formability. For the strain rates levels analysed (10^‐4 to 10^‐1 s^‐1) it was also observed that increasing the strain rate from 10^‐4 up to 10^‐1 s^‐1 leads to a 25 % difference in uniform tension elongation revealing the curve‐crossing phenomenon. Namely, strain rates equal or higher than 10^‐2 lead to a stagnation of strain hardening after a tensile strain of about 0.2. In order to investigate the results obtained, microstructural and thermal analyses were conducted and numerical simulations were performed. It was observed that the decreasing of formability of the material is essentially due to thermal aspects. In the discussion, the experimental and numerical results are analysed in terms of thermal softening, phase transformation and strain rate sensibility.     

Enrichment of marsh soils with heavy metals by effect of anthropic pollution

The impact of waste disposal on marsh soils was assessed in topsoil samples collected at eight randomly selected points in the salt marsh in Ramallosa (Pontevedra, Spain) at 4-month intervals for 2 years. Polluted soil samples were characterized in physico-chemical terms and their heavy metal contents determined by comparison with control, unpolluted samples. The results revealed a marked effect of waste discharges on the soils in the area, which have low contents in heavy metals under normal environmental conditions. In fact, the studied soils were found to contain substantial amounts of total and DTPA-extractable Cd, Cu, Pb and Zn. Based on the relationship of the redox potential with the DTPA-extractable Cd, Cu, Pb, and Zn contents of the soils, strongly reductive conditions raised the total contents in these elements by effect of their remaining in the soils as precipitated sulphides. Such contents, however, decreased as oxidative conditions gradually prevailed. The contents in DTPA-extractable metals increased with increasing Eh through the release of the metals in ionic form to the soil solution under oxidative conditions. The contents in heavy metals concentrating in the polluted soils were several times higher than those in the control soils (viz. 2 vs. 6 for Cd, 4 vs. 6 for Cu, 4 vs. 20 for Pb, and 2 vs. 15 for Zn, all in mg kg⁻¹). This can be expected to influence the amounts of available heavy metals present in the soils, and hence the environmental quality of the area, in the near future. Based on its geoaccumulation index (Class ≥3 for Cd and Cu, and 1–4 for Pb and Zn), the Ramallosa marsh is highly polluted with Cd and moderately to highly polluted with Cu, Pb and Zn. The enrichment factors obtained confirm that the salt marsh is highly polluted (especially with Cd) as the primary result of anthropic activity.     

Pheromone-based trapping of West Indian sugarcane weevil in a sugarcane plantation

Attraction of Metamasius hemipterus (Oliver) to gallon and bamboo traps baited with insecticide-treated sugarcane, the male-produced pheromone, 4-methyl-5-nonanol, and 2-methyl-4-heptanol is more efficient if ethyl acetate is added. The optimal traps are ground-level gallon traps baited with insecticide-laced sugarcane, pheromone, and ethyl acetate. Capture rates of ground-level gallon traps are doubled by placing an insecticide-laced pad under the trap, but significantly decreased by placing the trap on a stick above ground. The efficiency of ground-level gallon traps is the same as ground level ramp traps. Mass-trapping M. hemipterus in newly planted sugarcane using ground level bamboo traps baited with insecticide-laced sugarcane and pheromone over six months revealed populations were low for the first two months, became maximum at five months, and declined thereafter. Capture rates of traps bordering newly planted and mature sugarcane were not significantly different from capture rates of traps in the interior of the plots. Capture rates of bamboo traps containing only insecticide-laced sugarcane and deployed at 30 traps/ha averaged 6 weevils/trap/week compared with 66 weevils/trap/week for traps additionally containing pheromone lures and deployed at 5 traps/ha. Capture rates for bamboo traps baited with insecticide-laced sugarcane and pheromone and deployed at 10 and 15 traps/ha were 43 and 38 weevils/trap/week, respectively. Total captures were higher in those plots with a higher density of insecticide-laden sugarcane and pheromone baited traps, and the differences were approximately proportional to trap density in the range of 5–15 traps/ha. Capture rates of traps containing insecticide-laced sugarcane and pheromone were always higher than of traps containing only insecticide-laced sugarcane, but in the first two months after planting the differences were much greater than in months 3–6 after planting.     

Analysis of water soluble chloride content in concrete

RILEM Technical CommitteesRILEM TC 178-TMC: ‘Testing and Modelling Chloride Penetration in Concrete’

Analysis of water soluble chloride content in concrete Recommendation     

Cumulative impact assessment on air quality from multiple open pit mines

Both open pit mine and smelter projects can have significant impacts on a variety of environmental resources. Among these, air quality of the surroundings is a key issue. Additionally, the environmental assessment of projects demands integrated approach taking in account all pollution sources. Therefore, specific focus has been put on the methodology for assessing impacts on air quality. This paper proposes an integrated index of environmental impact aiming to quantify the air quality impact of industrial operations around an urban area, in case of scarcity of in situ acquired data. This proposed pollution index is demonstrated by a case study conducted in the municipality of Congonhas, Brazil, in which contributions of five open pit mines and two smelters were studied. To achieve the pollution index, the wind rose and distances from the centroids of effective areas to the urban nucleus itself were considered, taking into account the wind projection areas from windward impacting sources on the leeward impacted urban site. The proposed index also includes the squared wind speed (proportional to the kinetic energy transferred in uplifting dust from ground surface). The method proposed is considered suitable for impact assignment for each one of the air pollution sources in the neighborhood of studied area. Some fluid dynamic aspects of airborne particulate matter are also studied by proposing a new equation for threshold saltation speed.