Studies on chemical resistance of polyesters

Chlorendic anhydride based polyester ( I ,) tetrachlorophthalic anhydride based polyester ( II ), dibromoneopentyl glycol based polyester ( III ,) general purpose polyester ( IV ,) blend of dibromoneopentyl glycol based polyester with general purpose polyester ( V ,) chlorendic anhydride and dibromoneopentyl glycol based polyester ( VI ), and a blend of chlorendic anhydride based polyester and dibromoneopentyl glycol based polyester ( VII ) were prepared and their chemical resistance and moisture absorption studied in various reagents, acid, alkali, and water, at 25 and 65°C. It is found that the polyester ( III ) is the least affected in the presence of the acids. In 20% NaOH, there was a decrease in weight for all polyesters at both the temperatures compared to the control except the polyester ( VII ). Increase in weight of all the polyesters was observed during the absorption of moisture both at 25 and 65°C. The increase was higher at higher temperature. Polyester ( III ) thus shows the least absorption of moisture.     

12-tungstophosphoric and 12-tungstosilicicacid supported onto hydrous zirconia for liquid phase tert-butylation of m-cresol

Supported 12-tungstophosphoricacid (12-TPA) and 12-tunstosilicicacid (12-TSA) were used as heterogeneous catalysts for liquid-phase tert-butylation of m-cresol, an industrial important reaction. Alkylation reactions have been carried out with supported 12-TPA by varying different parameters such as % loading of 12-tungstophosphoricacid onto support, mole ratio of alcohol to m-cresol, reaction temperature, amount of the catalyst, reaction time and calcination temperature to optimize the conditions. To see the effect of the acidity on the reaction, the same reaction was studied over supported 12-TSA. Both the catalysts give 100% selectivity for o-isomer with different % conversion. The difference in catalyst performance of both the catalyst was correlated with the value of total acidity as well as Bronsted acidity.     

Synthesis and characterization of butyl acrylate graft sodium salt of partially carboxymethylated starch

Graft copolymers were synthesized by graft copolymerization of butyl acrylate (BA) onto sodium salt of partially carboxymethylated starch (Na‐PCMS). Ceric ammonium nitrate (CAN), a redox initiator, was used for initiation of graft copolymerization reaction. All the experiments were run with Na‐PCMS having degree of substitution, DS = 0.35. The grafting reaction was characterized by parameters such as % total conversion (%Ct), % grafting (%G), % grafting efficiency (%GE), and % add‐on. Graft copolymers were characterized by infrared spectral analysis and scanning electron microscopy. Variables affecting graft copolymerization reaction such as nitric acid concentration, reaction time, reaction temperature, and ceric ion concentration were investigated. The results revealed that 0.3M CAN as initiator, 0.3M HNO₃, with reaction time 4–4.5 h at 25–30°C were found as suitable parameters for maximum yield of graft copolymerization reaction. © 2006 Wiley Periodicals, Inc. JAppl Polym Sci 102: 3334–3340, 2006     

Frequency distributions of breaking load,tenacity, and ratio of cell wall thickness to ribbon width for single cotton fibers

Analysis of the frequency distributions of breaking load, tenacity, and ratio of cell wall thickness to ribbon width (C/R) for single cotton fibers in this study has indicated that they can all be represented by β-distributions. This suggests that a parallel model of element configurations exists in which there is a uniform distribution of elemental strengths in single cotton fibers before as well as after slack mercerization. In the case of breaking load and tenacity, the distributions are positively skewed and the skewness decreases on slack mercerization, suggesting that quite a few potentially weak places have been either completely removed or at least strengthened. The changes in C/R ratio on slack mercerization for cottons having a range of maturity have been examined and discussed. The dependence of properties such as breaking load, tenacity, and linear density on cell wall to ribbon width ratio (C/R) have also been studied.     

Adsorption of lipopolysaccharide on carbon sieves

Adsorption of lipopolysaccharide, LPS, on carbon sieves Carboxen 1003 and Carboxen 1010 has been studied. LPS adsorption kinetics is initially faster on smaller size (1-10 μm) particles of predominantly microporous Carboxen 1010 compared to Carboxen 1003 (150-200 μm) particles. However, the adsorption capacity of micro/meso/macroporous Carboxen 1003 by LPS is higher than that of Carboxen 1010 since the former carbon has wider pores that can accommodate large lipopolysaccharide molecules or their agglomerates. Carboxen 1010 probably adsorbs LPS mainly on the external (macropore) surface.     

HYDRODYNAMIC STUDIES IN FISCHER-TROPSCH DERIVED WAXES IN A BUBBLE COLUMN

Gas hold-up and Sauter mean bubble diameter measurements were made in a 0.051 m diameter by 3 m long glass bubble column in the system, nitrogen-molten wax, with three different waxes (paraffin wax FT-300, Sasol's Arge wax and Mobil's reactor wax). Paraffin wax has a tendency to foam and gas hold-up is a strong function of gas distributor type, temperature and start-up procedure, whereas the reactor waxes do not foam and are much less affected by these variables, In experiments at 265°C with a 1.85 mm single hole orifice plate distributor the gas hold-ups were nearly the same for all three waxes. However, significant differences in Sauter mean bubble diameters were obtained in experiments with different waxes; FT-300 wax produced the smallest Sauter mean bubble diameters whereas Mobil's reactor wax produced the largest bubbles. Addition of 1-octadecanol and octadecanoic acid (up to 10wt%) to the FT-300 paraffin wax caused an increase in gas hold-up and a delay in the foam break-up in runs at 265°C with the 1.85 mm orifice plate distributor.     

Novel isocyanate-free self-curable cathodically depositable epoxy coatings: Influence of epoxy groups on coating properties

Novel self-curable cathodically depositable coatings were developed from glycidyl functional epoxy ester-acrylic graft co-polymer (EEAG) without using any external crosslinking agents. The EEAG-amine adducts (EEAGAs) were prepared by reacting EEAG with varying amount of diethanolamine (DEoA) which are neutralized with acid and dispersed in deionised water to give stable dispersion for cathodic electrodeposition (CED) coatings. The dispersions were cathodically electrodeposited on phosphated steel panels and thermally cured to give uniform coating. The coatings were evaluated for different mechanical, chemical and corrosion resistance properties. The coatings were evaluated for their thermal properties using thermo gravimetric analysis (TGA). The final properties of the coatings were found to be affected by the amount of amine reacted with epoxy. The coating films showed good overall performance properties for their use in coating industry.     

A comparative investigation of interfacial adhesion behaviour of polyamide based self-reinforced polymer composites by single fibre and multiple fibre pull-out tests

Abstract

Interfacial adhesion of composite materials plays an important role in their mechanical properties and performance. In the present investigation, analysis of the interfacial properties of self-reinforced polyamide composites by using microbond multiple fibre pull-out test is emphasised. Microbond specimens prepared through thermal processing are tested for their interfacial properties by multiple fibre bundle pull-out tests and compared with that of traditional single fibre pull-out test specimens. Multiple fibre pull-out addresses the volume fraction as well as eliminates the possibility of fibre breakage before matrix shear. Higher scatter in the data in the samples is addressed in the present studies. FTIR and Fractographic studies are carried out for deep understanding of the post pull-out interfacial adhesion.     

Integration Concepts for the Fabrication of LTCC Structures

At the Keck Smart Materials Integration Laboratory at Penn State University, low-temperature co-fired ceramic (LTCC) material systems have been used to fabricate a number of devices for a variety of applications. This article presents an overview of the integration of the concepts and materials that we have used to achieve miniaturization and unique device function. Examples of microwave filters, metamaterial antennas, and a dielectrophoretic cell sorter will be presented, with emphasis on device modeling and design, prototype construction methods, and test results.     

Viscosity of binary mixtures. I. mono-, di-, and tri-n-butyl and -n-octylamine with cyclohexane

Viscosities for six binary mixtures of n-butylamine, di-n-butylamine, tri-n-butylamine, n-octylamine, di-n-octylamine, and tri-n-octylamine with cyclohexane have been measured at 303.15 K with an Ubbelohde suspendedlevel viscometer. Deviations of viscosities from a rectilinear dependence on mole fraction are attributed to H-bonding and to the size of alkylamine compounds. The application of the Eyring's theory of activation energy is examined. The free volume theory of Prigogine-Flory-Patterson (PFP) and the experimental excess enthalpy have been used to estimate excess viscosity ln = (ln / ₁ ⁰ – x ₂ ln ₂ ⁰ / ₁ ⁰ ) and corresponding free volume, enthalpy, and entropy contributions for five binary mixtures of tri-n-alkylamine: triethyl, tripropyl, tributyl, trihexyl, and trioctylamine with cyclohexane. A comparison of experimental and theoretical excess viscosities indicates a failure of the PFP theory when two components of the mixture differ considerably in size. The size difference contribution to excess viscosity is related to (V ₂ ^*1/2 – V ₁ ^*1/2 ), where V ₁ ^* and V ₂ ^* are hard-core volumes of two components of the mixture.