Congenital Y-type urethro-perineal fistula

A case of primary carcinoma of the urinary bladder associated with a primary retroperitoneal leiomyosarcoma is presented. Due to the lack of early symptoms, diagnosis of the retroperitoneal leiomyosarcoma was late and therefore the prognosis was poor. Twelve months after diagnosis the patient died not of the bladder tumor, but of the recurrent leiomyosarcoma.     

Determination of uranium in fertilisers using fission track method

Trace contents of uranium in various commercial fertilizers e.g. ureas, superphosphates, diammonium phosphates have been determined using fission track etch technique. The uranium content in ureas varies from .05 to 1.3 mg kg^–1 whereas in superphosphates it varies linearly with phosphate content.     

Experimental investigation of impact of diesel particulate filter on smoke and NO<Subscript>x</Subscript> emissions of a Euro-I compression ignition engine with active and off-board regeneration

Old engines (Euro III or earlier) produce more emissions, and it will be difficult to entirely stop their usage especially in developing and under-developed nations; hence, it is desired that appropriate emission reduction technologies are tested on such engines to analyze their feasibility and economical acceptability. While most such studies have been conducted on constant speed stationary engines and modern engines, this study tried to analyze the effectiveness of an uncoated wall-flow type ceramic diesel particulate filter on a Euro-I, water-cooled, direct injection, variable speed, compression ignition engine in a laboratory set-up in India. Also, this study focused on diesel particulate filter regeneration by two methods: active regeneration by diesel injection in the particulate filter using an electronic control unit and off-board regeneration by taking out and heating the diesel particulate filter in an electrical resistance furnace at 650 °C for 10 h. The results, in the form of smoke emission, NO_x emission and engine performance, obtained using both the regeneration methods were analyzed, and conclusions were drawn. It was found that using diesel particulate filter, particulate matter emissions (smoke) were almost entirely eliminated. It was also found that off-board regeneration had numerous advantages compared to active regeneration. Since a furnace would be needed for off-board regeneration, an exchange process for diesel particulate filter is suggested.     

A conformal cylindrical microstrip array for producing omnidirectional radiation pattern

Radiation patterns of rectangular microstrip patches arranged circumferentially on a circular cylinder have been computed. Both the axial patches and circumferential patches have been used. It has been found that the number of circumferential patches required for a given ripple in gain pattern is considerably less, thus simplifying the feed network. Comparison with experimental measurements shows good agreement.     

Stratification of forest density and its validation by NDVI analysis in a part of western Himalaya,India using Remote sensing and GIS techniques

This study deals with the assessment of the status of forest density in the Kangra district of Himachal Pradesh, western Himalaya. A classified forest map of the area with an accuracy of 88.17% was produced using the hybrid classification method in Erdas Imagine. An IRS 1D LISS III satellite image was used for mapping and classification. Forest density was calculated in the ArcGIS environment by overlaying a mesh of uniform resolution cells (500 m×500 m) on a classified forest map. The forest density value of each cell was later used for the preparation of forest density contours. The forest density output was verified by Normalized Difference Vegetation Index (NDVI) analyses. The forest cover of the study area was found to be 34.3%. Baroh area had the highest (45.87%) forest density and Baijnath (18.65%) the lowest. Central and western regions of the district showed high‐value forest density contours (>50%). The derived NDVI values were compared against the forest density classes for assessing the accuracy of the results obtained. A positive correlation (r = 0.99) between NDVI values and forest density confirms the accuracy of the results.     

Wear of grinding wheels

Wear phenomena accompanying cylindrical grinding were investigated directly from the wear particles removed from the wheel. The self-dressing mechanism was identified from the wear particle size distribution.     

Virtual modeling of an ankle foot orthosis for correction of foot abnormality

Clubfoot is a challenging structural foot abnormality in babies and generally occurs at birth or during childhood. Due to this the abnormal posturing of the foot causes the babies to turn the ankle inward and walk along the outside edges of the foot. In medical science it is known as “congenital talipes equino varus” (CTEV). Computer modeling of prosthesis and orthosis is a perspective method for optimal design and gait is a terminology related to walking patterns of human subject.     

Mixed boundary value problem of an infinite thick elastic slab containing a flat annular crack under torsion

In the present paper we consider the problem of determining the stress distribution in an infinitely long isotropic, compressible, homogeneous elastic slab containing a flat annular crack which is opened by internal shear stress. The faces of the slab are assumed to be stress free and the crack is located in the middle plane of the slab. The problem is formulated in triple integral equations which reduce to an infinite system of simultaneous equations, which are solved numerically.