Consideration of the mechanical behaviour of small fatigue cracks

The mechanical behaviour of small fatigue cracks is investigated for a low, medium and high strength material. At first an elastic consideration is performed which give a good impression how the stress fields change with crack size. In part 2 a full elastic-plastic analysis of short cracks is performed using a new numerical scheme to simulate the growth of shear bands emanating from the crack tip. The influence of material and loading paramters as well as of the crack size on the plastic crack tip opening displacement is discussed. It is also investigated how it is possible to get a conservative estimate of the crack tip deformation at small cracks.     

A new model of the effect of stirring intensity on the rate of secondary nucleation

Secondary nucleation in industrial crystallizers depends on both supersaturation and mechanical stress by stirring. Most models which consider mechanical stress assume that nucleation is proprotional to the energy transferred to the crystals during collisions. This is not based on any physical relationship and, in addition, the models do not satisfactorily reproduce the experimental results. Own model, based on the theory of Hertz/Huber, which accounts for the stress of the crystals caused by impact, gave better results. This well-known and proven theory allows the calculation of the volume abraded during collisions between crystals and stirrer or walls. Introducing a nucleate efficienncy, the effect of mechanical stress on the rate of secondary nucleation, due to stirring intensity and crystallizer size, can be determined.     

SOCIO-ECONOMIC ASPECTS OF THE AUSTRIAN 200 kWp-PHOTOVOLTAIC-ROOFTOP PROGRAMME

Between 1992 and 1994 a 200 kWp-rooftop programme to promote small grid-connected Photovoltaic (PV) systems was conducted in Austria. Within this programme about 100 PV systems with an average capacity of 2.28 kWp were installed. This paper investigates the socio-economic aspects of this programme and the prospects for a further dissemination of this technology. The major conclusions of this investigation are as follows: (1) The motives to invest in a PV system are: (i) environmental protection; (ii) an alternative to nuclear power; (iii) technical interest. Yet, it is also important that the public supports this purchase by means providing subsidies. (2) The purchase of a PV system leads to different changes in consumer behaviour. Consumers with low initial consumption increased their electricity demand slightly, while the majority of consumers with high initial electricity demand saved electricity. (3) The financial incentives in the programme were not optimally designed. With the same amount of total subsidies it would have been possible to promote more PV systems. (4) The key factors for a further dissemination of PV systems are: (i) financial incentives; (ii) a reduction of the investment costs; (iii) increase in reliability; (iv) distribution of information; (v) enhancement of environmental awareness.     

Influence of impurities and deformation temperature on the saturation microstructure and ductility of HPT-deformed nickel

Ni with different purities between 99.69 and 99.99 wt.% was deformed by high-pressure torsion (HPT) to high strains, where no further refinement of the microstructure is observed. The HPT deformation temperature varied between −196 and 400 °C. Both impurities and temperature significantly affect the lower limit of the grain size obtained by HPT. In the investigated samples, carbon was the most important impurity element in controlling the limit of grain refinement. The decrease in grain size due to an increase in the carbon content from 0.008 to 0.06 wt.% for HPT-deformed Ni samples at room temperature enhanced the ultimate tensile strength from 1000 to 1700 MPa. Surprisingly, the carbon content did not deteriorate the ductility, defined as the reduction in area, which is mainly limited by the total amount of impurities besides carbon. Furthermore, the deformation temperature dependency on ductility was not very pronounced and only visible for deformation temperatures above 200 °C.     

An experimental evaluation of a residential-sized evaporatively cooled condenser

In this paper, the performance of an innovative evaporatively cooled condenser is compared with that of a conventional air-cooled condenser for a split heat pump system. The system was tested in an environmentally controlled test chamber that was able to simulate test conditions as specified by ASHRAE Standard 116. Tests to optimize refrigerant charge and short tube restrictor size were conducted using refrigerant HCFC-22. The wheel rotation speed of the evaporative condenser was also optimized experimentally to maximize the coefficient of performance. Using these optimum parameters, steady state and cyclic performance tests were conducted. The experimental results showed that the evaporative condenser has a higher capacity than the air-cooled condenser by 1.8 to 8.1%, a higher COP by 11.1 to 21.6%, and a higher SEER by 14.5%.     

Quantitative phase evaluation of converter slags

The slags formed in the LD vessel during the refining process turn out with different chemical compositions, mineralogical structures and physical properties, in dependence on the charging and processing conditions. Electron probe microanalysis (EPMA) combined with a data processing method for mineralogical analysis was used to characterize the mineralogical phases in LD slags and moreover to determine their volume fractions. By this method some correlations between the phase contents and the chemical composition of LD slags were established. The diagrams gained from this work have proven to be a valuable aid for understanding the interrelationships between the chemical composition, the mineralogical structure and some physical properties of LD slags.     

Efficiency and effectiveness of promotion systems for electricity generation from renewable energy sources - Lessons from EU countries

Currently, a wide range of strategies is implemented in different countries to increase the share of electricity from renewable energy sources (RES-E). A still controversial discussion is whether quantity-driven (like Tradable Green Certificates (TGCs) based on quotas) or price-driven (like feed-in-tariffs (FIT)) instruments lead to preferable solutions for society. The core objective of this paper is to compare the perspectives of quota-based certificate trading systems for an efficient and effective increase of RES-E with FIT. The major results of this analysis are: (i) The success stories of growth in RES-E in EU member states in recent years has been triggered by FIT implemented in a technology-specific manner at modest costs for European citizens; (ii) At present, TGC systems in most countries applied show a low effectiveness with respect to RES-E deployment of less mature technologies such as solar PV (with improving tendencies in e.g. the UK or Italy with respect to certain technologies); (iii) Compared to short term trading in TGC markets the intrinsic stability of FIT systems appears to be a key element for success; (iv) Hence, currently a well-designed (dynamic) FIT system provides a certain deployment of RES-E in the shortest time and at lowest costs for society.     

A note on stability in three-phase-lag heat conduction

In this note we consider two cases in the theory of the heat conduction models with three-phase-lag. For each one we propose a suitable Lyapunov function. These functions are relevant tools which allow to study several qualitative properties. We obtain conditions on the material parameters to guarantee the exponential stability of solutions. The spectral analysis complements the results and we show that if the conditions obtained to prove the exponential stability are not satisfied, then we can obtain the instability of solutions for suitable domains. We believe that this kind of results is fundamental to clarify the applicability of the models.