Fluidised pellet bed bioreactor: a promising technology for onsite wastewater treatment and reuse.

A pilot-scale fluidised pellet bed (FPB) bioreactor, which combines chemical coagulation, biological degradation, particle pelletisation and separation in one unit, was applied for onsite wastewater treatment and reuse. As a result of rational use of inorganic coagulant and organic polymer and moderate mechanical agitation, spherical particles were generated in the upflow column and a well-fluidised bed was formed. With a continuous supply of dissolved oxygen through a recycling loop, an aerobic condition was kept in the bottom section of the FPB column. Under such conditions the pellets in the FPB column showed the following characteristics: (1) compact structure and high density; (2) rich in microorganisms; and (3) high MLSS and MLVSS concentrations. Therefore, the FPB bioreactor achieved more than 90% removal of SS, COD, BOD and TP from raw domestic wastewater within a total hydraulic retention time (HRT) of only about 30 minutes. It also showed nitrification and denitrification ability and the TN removal could be about 50% as the recycling ratio was increased to 1:1. The treated water quality is generally competitive with the secondary effluent from a conventional activated sludge process. With these advantages the FPB bioreactor is recommendable as a compact system for onsite wastewater treatment and reuse.     

北京城市供水安全及对策研究

“十一五”期间是首都经济社会快速发展的关键时期，也是应对水资源紧缺、保障供水安全的关键时期。确保首都供水安全是北京水务工作的第一要务，北京市水务局针对城市供水存在的主要矛盾和问题，对城市供水水源、水质水量、水厂、管网、设施等情况进行了全面调查，确定了工作思路，并据此提出了保障城市供水安全的目标和措施。     

对低水头电站规划设计的思考

文章结合平常工作经验,对低水头电站规划设计中需要注意的包括坝(闸)址选择,库区淹(浸)没、枢纽布置、施工导流、正常蓄水位与上下游梯级衔接五个问题加以分析探讨,进行总结和思考。     

High-breakdown-voltage AlInAs/GaInAs junction-modulated HEMT's(JHEMT's) with regrown ohmic contacts by MOCVD

A technology for increasing both the two-terminal gate-drain breakdown and subsequently the three-terminal-off-state breakdown of AlInAs/GaInAs high-electron-mobility transistors (HEMTs) to record values without substantial impact on other parameters is presented. The breakdown in these structures is dependent on the multiplication of electrons injected from the source (channel current) and the gate (gate leakage) into the channel. In addition, holes are generated by high fields at the drain and are injected back into the gate and source electrodes. These phenomena can be suppressed by increasing the gate barrier height and alleviating the fields at the drain. Both have been achieved by incorporating a p⁺-2DEG junction as the gate that modulates the 2DEG gas and by utilizing selective regrowth of the source and drain regions by MOCVD. The 1-μm-gate-length devices fabricated have two-terminal gate-drain and three-terminal-off-state breakdown voltages of 31 V and 28 V, respectively     

PC／ABS合金的研制及其在汽车上的应用

对ＰＣ／ＡＢＳ合金开发和研制及其在汽车上的应用作了评述。介绍了上海杰事公司在该领域的进展。     

圆盘式高速金属冷锯机锯切功率的实验研究

对１６００圆盘式高速金属冷锯机进行了锯切功率的实验研究。对某厂四种有代表性的产品，用不同的进锯速度，实测每种条件下的锯切功率变化，和最大瞬时锯切功率与平均锯切功率之比。并以实测数据为基础，得出每种产品以进锯速度为自变量的平均锯切功率回归公式。这些工作，不仅可以为这种冷锯机锯切功率的理论研究提供依据，还可直接为使用和设计这种冷锯机给出具体参考数据。     

温度,压力对漂移室气体增益的影响

研究了温度及气体压力对漂移室（工作于正比区）气体放大倍数的影响，温度和气体压力的变化范围分别是５￣４０℃及９０￣１０５ｋＰａ。用实验数据拟合得到了函数关系并测量了几种饱和度下函数中的参数值。     

智能化红外焊缝检测仪的实时信号自相关分析

详细介绍了在改进红外焊缝检测仪的过程中实时信号的一种抗干扰方法－－自相关方法。重点离自相关方法的数学模型，软件框图及设计思想，并给出了实验结果。     

基于逻辑器件的可编程增益放大器设计

本文介绍了可编程增益放大器设计的方法。它主要由控制电路、放大电路、显示电路三大模块组成。该系统性能好、成本低、工作可靠,具有一定的工程应用价值,经测试表明,该设计基本上达到了设计的要求。     

Crack tip parameters and elastic-plastic fracture of metals

By using optical displacement-measuring techniques we obtain the crack tip fields in terms of crack tip strain, crack opening angle (COA) and crack tip opening angle (CTOA). Thin plates with different crack configurations made of six elastic-plastic materials with strain hardening exponent ranging from 3 to are studied. We find that the COA resistance curve assumes certain characteristics common to all the materials. The experimental results indicate that the critical value of COA may be used as a fracture toughness parameter for these materials.

---

Résumé En utilisant une technique de mesure optique des déplacements, on obtient les champs régnant à l'estrémité d'une entaille, qui s'experiment par la déformation d'extrémité d'entaille, l'angle d'ouverture de la crique (COA et l'angle d'ouverture de la pointe de la crique (CTOA). On étudie des feuillards présentant différentes configurations de fissures et réalisés en six matériaux élasto-plastiques dont les modules d'écrouissage s'échelonnent de 3 à l'infini.On trouve que la courbe de résistance COA suppose certaines caractéristiques communes à tous les matériaux. Les résultats expérimentaux indiquent que la valeur critique du COA peut être utilisée comme paramètre de ténacité à la rupture pour les matériaux étudiés.