Toxic metals (Hg, Cd, and Pb) in fishery products imported into Italy: suitability for human consumption

Mercury, cadmium, and lead concentrations were determined in various fishery products (fishes, cephalopod molluscs, and crustaceans) imported into Italy from many European and non-European coastal countries. Considerable differences were found in the concentrations of these metals among the products tested. The highest mean Hg concentration was found in fishes (0.21 μg g(-1) wet weight), whereas cephalopods had the highest mean Cd concentration (0.35 μg g(-1) wet weight). Swordfish (0.80 μg g(-1) wet weight), longtail tuna (0.53 μg g(-1) wet weight), and thornback ray (0.52 μg g(-1) wet weight) had the highest concentrations of Hg, whereas maximum Cd concentrations were found in samples of common cuttlefish (0.85 μg g(-1) wet weight) and common octopus (0.64 μg g(-1) wet weight). The majority of the samples analyzed were in compliance with European Union legislation, except for a few cases. The calculated mean weekly intakes of Hg, Cd, and Pb through consumption of the fishery products tested were all below the legislated respective provisional tolerable weekly intakes. In general, the samples analyzed were considered safe to eat with regard to the metal concentrations found and the allowable intakes based on legislation. Nevertheless, the consumption of some species may be of significant importance for consumer health.     

The Affinity of Basic Dyes for Leacril 16 Acrylic Fibre

The dyeing affinity of some thiazole and benzothiazole basic azo dyes for Leacril 16 acrylic fibre was measured using Langmuir isotherms. Results show a close dependence of dye structure on affinity.     

Timing modulation of a 40-MHz laser-pulse train for target ranging and identification

We have demonstrated a target ranging and identification technique based on the timing modulation of a mode-locked laser coupled with fast incoherent detection. The range-to-target and the target-depth information have been determined with a resolution of better than 25 cm at single-pulse signal-to-noise ratios below 0.1. Our modeling results suggest that laser average power requirements remain a challenge, with upwards of 100 W likely needed for extension of this technique to ranges over 10 km, but improvements in overall system throughput would allow realization of its potential.     

Robot training of upper limb in multiple sclerosis: comparing protocols with or without manipulative task components

In this pilot study, we compared two protocols for robot-based rehabilitation of upper limb in multiple sclerosis (MS): a protocol involving reaching tasks (RT) requiring arm transport only and a protocol requiring both objects' reaching and manipulation (RMT). Twenty-two MS subjects were assigned to RT or RMT group. Both protocols consisted of eight sessions. During RT training, subjects moved the handle of a planar robotic manipulandum toward circular targets displayed on a screen. RMT protocol required patients to reach and manipulate real objects, by moving the robotic arm equipped with a handle which left the hand free for distal tasks. In both trainings, the robot generated resistive and perturbing forces. Subjects were evaluated with clinical and instrumental tests. The results confirmed that MS patients maintained the ability to adapt to the robot-generated forces and that the rate of motor learning increased across sessions. Robot-therapy significantly reduced arm tremor and improved arm kinematics and functional ability. Compared to RT, RMT protocol induced a significantly larger improvement in movements involving grasp (improvement in Grasp ARAT sub-score: RMT 77.4%, RT 29.5%, p=0.035) but not precision grip. Future studies are needed to evaluate if longer trainings and the use of robotic handles would significantly improve also fine manipulation.     

Impact of white-matter mask selection on DTI histogram-based metrics as potential biomarkers in cerebral small vessel disease

Magnetic Resonance Materials in Physics, Biology and Medicine - Histogram-based metrics extracted from diffusion-tensor imaging (DTI) have been suggested as potential biomarkers for cerebral small...     

Distortion correction of echo planar images applying the concept of finite rate of innovation to point spread function mapping (FRIP)

Objective

Point spread function (PSF) mapping enables estimating the displacement fields required for distortion correction of echo planar images. Recently, a highly accelerated approach was introduced for estimating displacements from the phase slope of under-sampled PSF mapping data. Sampling schemes with varying spacing were proposed requiring stepwise phase unwrapping. To avoid unwrapping errors, an alternative approach applying the concept of finite rate of innovation to PSF mapping (FRIP) is introduced, using a pattern search strategy to locate the PSF peak, and the two methods are compared.

Materials and methods

Fully sampled PSF data was acquired in six subjects at 3.0 T, and distortion maps were estimated after retrospective under-sampling. The two methods were compared for both previously published and newly optimized sampling patterns. Prospectively under-sampled data were also acquired. Shift maps were estimated and deviations relative to the fully sampled reference map were calculated.

Results

The best performance was achieved when using FRIP with a previously proposed sampling scheme. The two methods were comparable for the remaining schemes. The displacement field errors tended to be lower as the number of samples or their spacing increased.

Conclusion

A robust method for estimating the position of the PSF peak has been introduced.