Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

Mixed oxide supported hydrodesulfurization catalysts—a review

Support effects form important aspect of hydrodesulfurization (HDS) studies and mixed oxide supports received maximum attention in the last two decades. This review will focus attention on studies on mixed oxide supported Mo and W catalysts. For convenience of discussion, these are divided into Al₂O₃ containing mixed oxide supports, TiO₂ containing mixed oxide supports, ZrO₂ containing mixed oxide supports and other mixed oxide supports containing all the rest. TiO₂ containing mixed oxides received maximum attention, especially TiO₂–Al₂O₃ supported catalysts. A brief discussion about their prospects for application to ultradeep desulfurization is also included. An overview of the available literature with emphasis on research carried out in our laboratory form the contents of this publication.     

Allocentric Versus Egocentric Spatial Memory After Unilateral Temporal Lobectomy in Humans.

Thirty patients who had undergone either a right or left unilateral temporal lobectomy (14 RTL; 16 LTL) and 16 control participants were tested on a computerized human analogue of the Morris Water Maze. The procedure was designed to compare allocentric and egocentric spatial memory. In the allocentric condition, participants searched for a target location on the screen, guided by object cues. Between trials, participants had to walk around the screen, which disrupted egocentric memory representation. In the egocentric condition, participants remained in the same position, but the object cues were shifted between searches to prevent them from using allocentric memory. Only the RTL group was impaired on the allocentric condition, and neither the LTL nor RTL group was impaired on additional tests of spatial working memory or spatial manipulation. The results support the notion that the right anterior temporal lobe stores long-term allocentric spatial memories. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

Mathematical Modeling of Thermomechanical Processes under Intense Thermal Effect

Mathematical models of thermomechanical processes which are based on the laws of rational thermodynamics of irreversible processes are treated. Singular features of the unsteady-state behavior of a continuous medium are demonstrated within different models, such as a medium with internal parameters of state, a medium with memory, and a medium of the velocity type.     

NANODEV: A Nanoelectronic-Device Simulation Software System

The concept and structure of the NANODEV simulation software are described. NANODEV deals with nanoelectronic devices that exploit single-electron tunneling, resonant tunneling, or quantum interference. It can use both simplified and sophisticated models and enables one to evaluate a wide variety of devices and configurations. The capabilities of NANODEV are illustrated by examples.     

Low supply voltage high-performance CMOS current mirror with low input and output voltage requirements

This paper presents a scheme for the efficient implementation of a low supply voltage continuous-time high-performance CMOS current mirror with low input and output voltage requirements. This circuit combines a shunt input feedback and a regulated cascode output stage to achieve low input resistance and very high output resistance. It can be used as a high-precision current mirror in analog and mixed signal circuits with a power supply close to a transistor's threshold voltage. The proposed current mirror has been simulated and a bandwidth of 40 MHz has been obtained. An experimental chip prototype has been sent for fabrication and has been experimentally verified, obtaining 0.15-V input-output voltage requirements, 100-/spl Omega/ input resistance, and more than 200-M/spl Omega/ (G/spl Omega/ ideally) output resistance with a 1.2-V supply in a standard CMOS technology.