Polyacrylonitrile/α-Fe2O3 Hybrid Photocatalytic Composite Adsorbents for Enhanced Dye Removal

The potential of a novel α-Fe₂O₃/polyacrylonitrile (PAN) hybrid composite adsorbent to eliminate methylene blue (MB) from aqueous solution was evaluated. PAN was selected as the base composite. The presence of α-Fe₂O₃ as nanophotocatalyst on the surface of PAN introduced an efficient photocatalytic hybrid composite adsorbent for degrading MB. Effects of α-Fe₂O₃ nanopowder loading, pH, temperature, MB initial concentration, solar light, and contact time were investigated. Langmuir, Freundlich, and Temkin isotherms were applied to analyze the adsorption behavior. The Freundlich equation provided the best correlation with experimental data. Pseudo-first-order, pseudo-second-order, and intraparticle models were employed. Thermodynamic studies indicated an endotherm and spontaneous adsorption process in a defined temperature range.     

Nonisothermal suspension polymerization of vinyl chloride for enhanced productivity

In the present study, a mathematical model is developed to numerically predict nonisothermal batch suspension polymerization of vinyl chloride. Free volume theory was used to consider diffusion‐controlled reactions. Model predictions were validated against field data obtained in a pilot scale stirred tank reactor. Variable temperature trajectory was considered during the course of the reaction to improve productivity by reducing the polymerization time for a certain conversion. Variable temperature during the course of the polymerization was successfully implemented by considering the predefined K value. By using variable temperatures during the course of the reaction, the density of the short branches per 1,000 monomer units as a criterion for structure defect remained relatively unchanged. Maximum reduction in reaction time relative to the isothermal case with the same K value and final conversion was 44% for the best temperature trajectory. J. VINYL ADDIT. TECHNOL., 22:470–478, 2016. © 2015 Society of Plastics Engineers     

The pozzolanic reactivity of monodispersed nanosilica hydrosols and their influence on the hydration characteristics of Portland cement

This study reveals that the nanosilica hydrosols with higher specific surface areas had faster pozzolanic reactivity, especially at early ages; moreover, the results are indicative of the accelerating influence of nanosilicas and silica fume on the hydration of cement. Faster initial and final setting times observed for cement pastes containing nanosilicas are consequence of these mechanisms. However, less hydration degree of cement compared to the plain paste was observed at age of 7 days and after. This can be attributed to the entrapment of some of mix water in the aggregates of nanosilicas formed in cement paste environment, making less water available for the progress of cement hydration. The same mechanism is believed to be responsible for the reduction of flowability of cement pastes.     

Physical,morphological, and biological studies on PLA/nHA composite nanofibrous webs containing Equisetum arvense herbal extract for bone tissue engineering

A series of herbal extract incorporated into poly(lactic acid) (PLA) composite nanofibrous scaffolds were successfully prepared by using electrospinning technique. Equisetum arvense extract (EE) and nanohydroxyapatite (nHA) in different quantities were loaded into PLA solution to fabricate composite nanofibrous webs under various electrospinning conditions. Uniform nanofibers were obtained with an average diameter of 157 ± 47 nm in the case of those containing the herbal extract. Characterization of the webs was carried out by means of Fourier transform infrared (FTIR) spectroscopy, field emission‐scanning electron microscopy (FESEM), energy‐dispersive X‐ray spectroscopy (EDX), and differential scanning calorimetry (DSC) techniques. Mechanical properties, porosity, and contact angle of the prepared webs were also determined. Releasing behavior was investigated in phosphate buffer solution (pH 7.2) medium. Moreover, cell studies and osteogenic capacity were assessed in vitro using human adipose tissue‐derived mesenchymal stem cell (AT‐MSC). Evaluations of cell attachment, spreading, and proliferation of AT‐MSC were done by SEM observation and thiazolyl blue (MTT) assay. Osteogenic differentiation capability of AT‐MSC on the nanofibrous webs was analyzed by alkaline phosphatase activity and calcium content assay. It was found that with the addition of nHA and EE to PLA nanofibrous webs, their surface hydrophobicity was reduced while the tensile strength and Young's modulus were increased satisfactorily. Regarding the samples containing EE and nHA, cellular adhesion was observed with flattened normal morphology. Osteogenic differentiation of AT‐MSC on PLA/nHA/EE webs showed the highest mineralization capacity after 3 weeks which, was about 1.8 and 3 times higher than that of PLA/nHA and tissue culture polystyrene as control, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45343.     

Preparation and study of a thermo-responsive membrane using binary liquid crystal mixtures of cholesteryl cetyl ether and cholesteryl oleyl carbonate

A facile method for the synthesis of thermotropic liquid crystalline cholesteryl cetyl ether (CCE) was carried out from cholesterol and cetyl alcohol using montmorillonite K-10 as an acid catalyst. The aim of this study was to investigate the use of liquid crystalline blends of CCE and cholesteryl oleyl carbonate (COC) with appropriate crystal to smectic phase temperature (T _c?Cs) just above body temperature as a temperature-modulated drug permeation system. Using 30/70?mol ratio of COC/CCE, a mixture of desirable phase transition temperature was obtained. The phase transition behavior of COC/CCE binary liquid crystalline mixture was established by differential scanning calorimetry and polarizing optical microsopy. The COC/CCE-embedded cellulose nitrate membrane was used by an in vitro drug penetration studies. Paracetamol and mesalazine were chosen as hydrophobic and hydrophilic drug models, respectively. Paracetamol permeability through the membrane was higher at temperatures above the phase transition of liquid crystal (LC) blends (39?°C) than its permeability below the phase transition temperature of liquid crystal blends (30?°C). The drug penetration through LC-embedded cellulose membrane was influenced by the pore size of the membrane and therefore the adsorbed amount of LC. There was no penetration of mesalazine through that membrane presumably, due to the differences in hydrophilicity of LC-embedded membrane and permeated drug.     

Thermosensitive nanosized micelles from cholesteryl-modified hydroxypropyl cellulose as a novel carrier of hydrophobic drugs

The thermosensitive micelles based on the two series of cholesteryl-modified hydroxypropyl cellulose (series 1 and 2, respectively) were used as a promising drug carrier. The polymers 1a and 2a with side chain substitution degrees D _Chol?=?0.7 and 2.1?mol% were selected for micelle preparation, respectively. Polymeric micelles were prepared by the co-solvent evaporation method. The aqueous self-assembly of the polymers was studied using fluorescence analysis and transmission electron microscopy (TEM). The critical micelle concentrations (CMCs) values of the various D _Chol of polymers were evaluated in the range of ca. 0.13?C0.29?g/L which decreased with the increase of D _Chol in both series. Furthermore, the CMC values displayed a downtrend profile, with increasing the temperature. The polymer 1a with less D _Chol had lower CMC than that of polymer 2a. By using the naproxen as a hydrophobic model drug, the drug-loaded micelles were prepared. The TEM image of naproxen-loaded micelles of polymer 1a with 40?% drug-loading efficiency and 8?% loading capacity showed that micelles were regularly spherical in shape with a mean diameter of 70?nm. The unmodified HPC exhibited a lower critical solution temperature (LCST) of more than 41?°C in water, while polymeric micelles in aqueous solution presented an LCST of 38.7?°C. A drug release study was performed by dialysis method in phosphate-buffered solution at 25, 37 and 40?°C, respectively. The release kinetics of naproxen from the polymeric micelles revealed a thermosensitivity, since its release rate was higher at 40?°C than at 25?°C.     

Optimizing the mechanical and physical properties of thermoplastic starch via tuning the molecular microstructure through co‐plasticization by sorbitol and glycerol

Nowadays, environmental hazards caused by plastic wastes are a major concern in academia and industry. Utilization of biodegradable polymers derived from renewable sources for replacing common petroleum‐based plastics is a potential solution for reducing the problem. In this regard, starch has become one of the most promising alternatives to non‐biodegradable polymers for depleting plastic waste thanks to its low expense, abundance, renewability and biodegradability. However, the main drawbacks of starch are its poor processability, weak mechanical properties and severe hydrophilicity. In this work, thermoplastic starch (TPS) samples have been prepared using glycerol and sorbitol as co‐plasticizers in a laboratory co‐rotating twin screw extruder. Based on the mechanical test results, glycerol caused higher elongation to break but had lower tensile strength and elastic modulus compared to sorbitol plasticized starch. Fourier transform infrared spectroscopy and DSC results indicated that the hydrogen bond interaction between starch chains and plasticizers could be improved by replacing glycerol by sorbitol, which resulted in higher resistance against retrogradation proved by XRD results. TGA illustrated that the higher the sorbitol to glycerol ratio was, the more stable was the TPS. Using a proper amount of plasticizers (42 wt% total plasticizer, sorbitol to glycerol ratio 2:1) led to the preparation of a TPS sample with optimized properties including enhanced mechanical properties, high thermal stability, strong hydrogen bond formation and high resistance against retrogradation. © 2017 Society of Chemical Industry     

Shock-Wave Attenuation and Energy-Dissipation Potential of Granular Materials

The propagation of uniaxial-stress planar shocks in granular materials is analyzed using a conventional shock-physics approach. Within this approach, both compression shocks and decompression waves are treated as (stress, specific volume, particle velocity, mass-based internal energy density, temperature, and mass-based entropy density) propagating discontinuities. In addition, the granular material is considered as being a continuum (i.e., no mesoscale features like grains, voids, and their agglomerates are considered). However, while the granular material is treated as a (smeared-out) continuum, it is recognized that it contains a solid constituent (parent matter), and that the structurodynamic properties (i.e., Equations of State (EOS) and Hugoniot relations) of the granular material are related to its parent matter. Three characteristic shock loading regimes of granular material are considered and, in each case, an analysis is carried out to elucidate shock attenuation and energy dissipation processes. In addition, an attempt is made to identify a metric (a combination of the material parameters) which quantifies the intrinsic ability of a granular material to attenuate a shock and dissipate the energy carried by the shock. Toward that end, the response of a typical granular material to a flat-topped compressive stress pulse is analyzed in each of the three shock loading regimes.     

Microstructures and mechanical properties of friction stir welded dissimilar steel-copper joints

Welding dissimilar metals by fusion welding is challenging. It results in welding defects. Friction stir welding (FSW) as a solid-state joining method can overcome these problems. In this study, 304L stainless steel was joined to copper by FSW. The optimal values of the welding parameters traverse speed, rotational speed, and tilt angle were obtained through Response surface methodology (RSM). Under optimal welding conditions, the effects of welding pass number on the microstructures and mechanical properties of the welded joints were investigated. Results indicated that appropriate values of FSW parameters could be obtained by RSM and grain size refinement during FSW mainly affected the hardness in the weld regions. Furthermore, the heat from the FSW tool increased the grain size in the Heat-affected zones (HAZs), especially on the copper side. Therefore, the strength and ductility decreased as the welding pass number increased because of grain size enhancement in the HAZs as the welding pass number increased.