Fabrication of a proton exchange membrane via blended sulfonimide functionalized polyamide

A novel linear non-fluorinated sulfonimide functionalized polyamide (SPA) polymer electrolyte was successfully synthesized via an aromatic sulfonimide monomer with superior thermal stability and superacidity. The aromatic sulfonimide remains stable below 220 °C. To fabricate membranes with strong mechanical strength and dimensional stability, the polymer was blended with various quantities of PVdF. The PVdF/SPA blend membranes exhibit an excellent capacity of water uptake and high dimensional stability. However, their proton conductivity was found to be substantially lower than that of Nafion 211. Analysis on the SEM images of the PVdF/SPA blend membranes reveals that the low proton conductivity is primarily caused by the large pore structures (>1 μm), which lead to breakdown of the continuous proton transport channels.     

Influence of Interfacial LSMO Nanoparticles/Layer on the Vortex Pinning Properties of YBCO Thin Film

YBa₂Cu₃O_7?δ (YBCO) thin films have been deposited on bare and La_0.67Sr_0.33MnO₃ (LSMO) modified single crystal SrTiO₃ (STO) substrates. The effect of randomly distributed ferromagnetic LSMO nanoparticles and a complete LSMO layer, present at STO/YBCO interface, on the superconducting properties of YBCO thin films has been investigated by temperature dependent magnetization studies. The YBCO thin film on LSMO nanoparticles decorated STO substrate shows significant improvement in the critical current density and pinning force density as compared to the YBCO thin film deposited on bare STO substrate and this improvement is more significant at higher applied magnetic field. However, the LSMO/YBCO bilayer showed the improved flux pinning properties only up to a magnetic field of 1.5 T above which it deteriorates. In the case of LSMO/YBCO bilayer, the underlying LSMO layer gives rise to magnetic inhomogeneities due to domain structure, which leads to improved flux pinning properties limited to lower field. However, in the case of LSMO nanoparticles decorated substrate, the presence of LSMO nanoparticles at YBCO/STO interface seems to introduce magnetic inhomogeneities as well as structural defects, which might be acting as correlated pinning sites leading to improved flux pinning properties of the YBCO thin film over a wide range of applied magnetic field.     

Intel 870: a building block for cost-effective, scalable servers

Architects based the Intel 870 system architecture on the scalability port, a coherent system interconnect. The system's building-block approach lets a single chip set support a wide range of server segments.     

Yield-oriented computer-aided defect diagnosis

Any good yield-oriented defect strategy must have two main components-(a) the ability to perform rapid defect diagnosis for yield learning, and (b) the ability to efficiently extract defect parameters from the manufacturing line. In this work, an inductive fault analysis (IFA)-based defect methodology is investigated to see if it meets the above requirements. Using an SRAM test vehicle as an example, the research analyzes whether computer-generated mappings between defect types and tester fail data can provide sufficient resolution for both, defect diagnosis and defect parameter characterization     

Photoelectrochemical solar cells using electrodeposited GaAs and AlSb semiconductor films

Electrodeposited GaAs and AlSb thin film semiconductors were prepared under various deposition conditions. Reasonable stoichiometry could be attained as revealed by EDAX studies. The best stoichiometry was obtained are Ga_1·04As_0·96 and Al_1·12Sb_0·88. The band gap of the GaAs and AlSb films was ∼1·5 eV and 1·6 eV respectively. The electrochemical and photoelectrochemical studies on these films are reported with different redox-couples in aqueous and non-aqueous medium.     

Heat transfer through electrolytic solutions under the action of electrolytic currents

Heat transfer rates from an electrically heated thin platinum wire in dilute NaOH and Na₂CO₃ solutions of different concentrations have been measured under the influence of electrolytic currents, using a sensitive Kelvin double bridge. In the low concentration region, the rate of heat transfer is initially found to increase with concentration and then to decrease with further increase in concentration. An explanation of these results on the basis of the behaviour of the thermal boundary layer surrounding the hot wire electrode is suggested. It has been indicated that these results can be employed to improve the performance of boiler systems and electro chemical machining processes.